-
Product
256-Element Active Antenna Innovator’s Kit
AWA-0142
-
The AWA-0142 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0135 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0135, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0142 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
Product
SparkFun Breakout
HMC6343
-
The HMC6343 is a fully integrated high end electronic compass module that can compute and give you a heading direction that’s accurate within a couple degrees. It is tilt compensated and is calibrated to handle magnetic distortions. This breakout board allows for easy use of the HMC6343. All that is required is power and I2C connections to a microcontroller so that the module can receive commands and send data back to the user.
-
Product
BARE BOARD TEST PROBES
-
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
Product
Battery Pack PCM Test Equipment
-
Xiamen WinAck Battery Technology Co., Ltd.
This battery PCM/PCB test equipment is suitable for the basic parameter test and protection function test of lithium battery pack protection board of mobile phone & digital products; it is also used for downloading, comparing and PCB calibration of battery management.
-
Product
Power Distribution Boards
-
Power distribution systems can be offered in addition to solutions for power supplies. This includes power distribution boards, which take over the power distribution in your system. When developing the system solution, in addition to the technical requirements such as high energy efficiency, simple further processing is decisive. The competence for high-performance circuit boards, enclosure constructions as well as assembly and system tests, which has been developed over the years, enables us to offer you the best possible power supply and distribution.
-
Product
SBC
PPC11A
-
The PPC11A supports the same technology insertion pin-out as previous members of the PowerXtreme family including popular boards such as the PPC4A, PPC7A, PPC9A and PPC10A, minimizing integration time and effort for legacy upgrades.
-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
3.5" Single Board Computer
-
Advantech 3.5" Pico-ITX delivers fanless, power-efficient features powered by NXP, Qualcomm, Rockchip, and TI to edge AI and embedded applications.
-
Product
Digital Panel Meter
DC
-
Laureate DC voltage and current panel meters with a DC signal conditioner board combine high accuracy with high read rate and a wide range of isolated output options for computer interface and control. Accuracy is 99.99% of full scale 1 count. Used as a direct-reading DC voltmeter, the Laureate provides a full-scale readout of 20,000 counts and six full-scale voltage ranges from 200.00 mV with 10 mV resolution to 600.0 V with 100 mV resolution.
-
Product
PXI Optical FPGA Board
PXIe-8324-DSP
-
The Conduant PXIe-8324-DSP FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its two 12-lane HSS interfaces while performing complex calculations.
-
Product
192 X 1 High Density Relay Multiplexer
DP-cPCI-4383
-
DP-cPCI-4383 is a 192 Channel high density Relay Multiplexer module. DP-cPCI-4383 is implemented as a 6U cPCI module. As a 192 channel multiplexer one input can be multiplexed to any of the 192 outputs. The 192 channels are divided into 8 banks of 24 channels each. This combination allows the board to be used as one group of 192x1 or two groups of 96x1 or four groups of 48x1 multiplexer. The banks are isolated from each other using tree switches.
-
Product
CPCI/PICMG 2.16 Intel Core 17th Gen. System
CP6004-RA_RC
-
The CP6004-RA/RC, a CompactPCI PICMG 2.16 compliant 6U CPU board, comes with various rugged levels, making it yet another addition to Kontron’s rugged PICMG 2.16 portfolio.Based on the Intel® Core™ i7 third generation processor and the QM77 platform controller hub, the CP6004-RA/RC is featured by dual or quad core computing performance at a reasonable thermal design power, including a complete set of data, communication and multimedia interfaces.
-
Product
Motion Control Terminal Board for Yaskawa Sigma II Servo Amplifiers
DIN-814PA
-
This well-designed motion control terminal board is for the users who use Panasonic MINAS A super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
128 Channel Digital I/O Modular PXI Card
GX5733 Series
-
The GX5733 is a 3U modular digital I/O card that offers up to 128 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5733 offers the highest channel density and flexibility in the industry for a single-slot, 3U PXI plug-in board. 96 channels support TTL levels and an additional 32 I/O channels can be customized by installing one of Marvin Test Solutions' GX57xx series I/O modules. Alternatively, the remaining port can be configured to support 32 TTL channels.
-
Product
32-CH Discrete Input Daughter Board Module
HSL-DI32-DB-N
-
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
CPCI or PXI Digital IO Board
MS 1802
-
*Bus Interface - PCI Bus*Number of Channels 198*Compatibility - TTL*Power on state - Inputs (high-Z), pulled up or down (jumper selectable)*Handshaking - Input, Output, or bi-directional*Data transfers - Interrupts, programmed I/O*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Design, Manufacture & Test of Complex RF/Microwave Printed Circuit Boards (PCBs)
-
Teledyne Labtech specialises in the design, manufacture and test of complex RF/Microwave printed circuit boards (PCBs). - Technology driven – we innovate- Turnkey - one stop for manufacture, assembly & test- Focused – technical design support for RF/microwave and large format PCBs
-
Product
3U VPX VITA 66.5 FPGA board with FMC+ Site
IC-FEP-VPX3f
-
Based on the latest Xilinx Kintex® UltraScale™ 20nm FPGA family, the IC-FEP-VPX3f is the first VITA 66.5 compliant FPGA board available. It is the perfect solution for applications requiring DSP-intensive processing in a 3U VPX form factor.
-
Product
3U OpenVPX Multifunction I/O Board
68G5
-
NAI’s latest generation 3U OpenVPX Multifunction I/O and Communications Board, the 68G5, can be configured with up to three intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-C optimized systems.
-
Product
MECHANICAL TEST FIXTURE KITS
TX-MT-100 SERES
-
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
-
Product
PHOTOMASK INSPECTION MACHINE
NEGATIVE FILM
-
Negative film and photomask inspection originated from the extensive use of printed circuit boards. Negative films and photomasks are used in large quantities. The early detection method is to use the "inspection light table" for inspection, which requires too much manpower and material resources, and manual testing may be due to eye fatigue and negligence.
-
Product
Debug Adapters
-
One thing is sure in the life of an embedded developer - your next microcontroller development board will be fitted with a different debug connector to the one used in your previous design.
-
Product
Single Board Computer
VF370
-
Sundance Multiprocessor Technology Ltd.
The VF370 is a 3U OpenVPX Single Board Computer (SBC) module that utilises the Intel Atom® E39xx series of embedded processors, Intel Cyclone® V FPGA technology and a FMC mezzanine site, to provide a module with scalable processing power and flexible IO options for reduced Size, Weight and Power (SWaP) applications. It is available in standard air-cooled and rugged conduction-cooled versions.
-
Product
I/O Wiring Terminal Boards
ADAM-3900 & PCLD Series
-
ADAM-3000 series consists of cost-effective, configurable, isolated signal conditioning modules. They are able to operate in harsh environments.
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
-
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
3.4 MP GMSL Camera (supports Upto 15 Meters)
NileCAM30_USB
-
NileCAM30_USB is the four board solution containing the camera module, serializer, deserializer and USB base board. This camera is based on AR0330 CMOS image sensor from ON Semiconductor®, with USB 3.1 Gen 1 interface. The NileCAM30_USB comes with 15 meters coaxial cable with FAKRA connector at both ends of serializer/deserializer board. The NileCAM30_USB has an S-mount (M12) lens holder which allows customers to choose and use the lens according to their application requirement.
-
Product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
-
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
Product
Expansion Adapter Chassis
TB3-TO-CMC-LP
-
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
