Contacts
See Also: Modules, Wire, Connectors, Patchcords, Flying Leads
-
Product
500-Pin SEARAY Connector, Male with Backshell, 1 Amp, 500 Port
C500RMR-4SB-0A
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Receiver, G6, 6 Module, Keying Feature
310104318
Receiver
The Receiver for the G6 is equipped with keying, a locking handle and nickel plated steel slides that engage up to 1,440 signal contact points. It allows a high amount of I/O within a compact and rugged device.
-
Product
PXI Ultra High Density 64x4 2-Pole Matrix
40-533B-022
Matrix Switch Module
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
Product
Open Top BGA Sockets
-
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 64 Position, w/ Right Angle Contacts
510104187
Receiver Module
Primary mating module 510108101. (May mate with other ITA modules, as well.)
-
Product
Data Logger with GSM/GPRS Module
HD33M-MB.2
-
GSM/GPRS data logger. RS485 MODBUS-RTU input, additional contact input for rain gauge. Great to combine with HD52.3D and HD51.3D series anemometers!
-
Product
Eurostat Turnstiles
-
For companies who need to ensure that the operators cannot enter the EPA unless their wrist straps and footwear are compliant every day• The turnstiles comply with ANSI/ESD S20/20 specification and ISO standards record keeping requirements • Both ESD safe shoes are tested separately through measuring electrodes, installed in the contact mat.• This system tests operators quickly (≤ 3 sec) and automatically and generate reports for the ESD coordinator• Communication with a server for traceability (Operator ID, Time & Date, Test values etc…)• LCD screen showing real time measurement• Keypad• Hygrometry measurement• Choice of measuring ranges and system calibration directly with the software• HID Wiegand interface, compatible to any HID card format
-
Product
Process Timers
TCT101-1ABC
-
The Process Timer TCT101-1ABC is a panel mount 4 digit 2 line display meter that can be set up for various Timer functions, such as Timer Off, Timer On, Pause Timer, Timer On and Off, Propotinal Timer. The TCT101-1ABC has 2 relays that can be used for various functions and has 5 Amp contacts. The timer periods can be set in multiples of 1 hundredths, 1 tenths of a second, seconds, minutes or hours. With the aid of the front touch panel or digital input it is possible to interrupt the timer. The unit also has a function that can set the output to toggle on and off over a period of time.
-
Product
Enclosures
-
VPC offers a variety of options to customize standard enclosures to meet any application need. Use VPC's Customer Wirelist Template to quickly communicate your overall requirements. VPC can provide options such as cutouts, secondary connectors, silk screening, engraving, and much more. Contact a Field Application Engineer for assistance designing a custom enclosure to meet your test needs.
-
Product
Board Level Products
-
MicroImage Video Systems offers many of our products as board level allowing OEM’s (Original Equipment Manufacturers) to utilize MicroImage technology in their own products. While we offer many off the shelf products in board level, we can also offer customized versions with different connections and features in reasonable minimum quantities (starting as low as 25 pcs per order for some products). If you don’t see exactly what you are looking for, ask us, it may be something we have already designed or something we can change easily. Contact us today with your requirements.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Mini Coax, Contact, ITA, RG178
610103130
Coax Contact (ITA)
Primary mating contact 610104141. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 30µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance < 5 milliohms @ 0.5 Amp & always < 10 milliohmsCable Specifications RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
Product
Contact Level Sensors
-
Contact level devices come in contact with the tank media and are used for point or cocntinious level measurement. Types include Float, Optical, RF Capacitence, Conductivity, Ultrasonic, Tuning Fork.
-
Product
8 Relay Output PCIe Board, 8 Isolated Digital Input Channels, 24V
APCIE-2200-8-8
-
- 8 electromechanical relays with change-over contacts The PCI-Express 8 relay board APCIe-2200-8-8 has 8 relay output channels and 8 isolated digital inputs, 24 V. 7 inputs are interruptible. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
Coax, Contact, ITA, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102134
Contact Adapter (ITA)
Coax, Contact, ITA, 20/26 GHz, 3.5MM, with SMA Adapter (90 Series modules only)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination 3.5mm compatibleInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications 3.5mm compatibleEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ min.
-
Product
Signal / Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/twin female contacts
510160112
Receiver Module
This module comes fully loaded with twin female contacts (p/n 610138200), iCon modules mount from the rear of the iCon/i1 receiver allowing installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
Thermocouple, Contact, ITA, Chromel, Type K (°C)
610113133
Thermocouple Contact (ITA)
Primary mating contact 610113131.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
Product
Contact Resistance Meter
CRM 100C
-
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Optical Tensiometers
Theta Flex
-
Attension® Theta Flex is a contact angle meter that enables all measurements in one instrument for both research and quality control. It measures static and dynamic contact angle, 3D surface roughness, surface free energy, surface and interfacial tension, and interfacial rheology.
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
Integrated Balun Probes
-
This is an example of a 900 MHz Integrated Balun Probe. It incorporates a 50 ohm unbalanced to 200 ohm balanced differential transformer. The probe can be built with or without a center tapped ground needle and may also incorporate DC bias through the differential pair or via separate needle contacts.
-
Product
Rugged Door Contact Sensor with Universal-Style Magnet
ENVIROMUX-DCSR-U
-
Monitors access with a magnetic bridge sensor (no special inserts necessary). Ideal for commercial and industrial installations in harsh environments. Heavy-cast aluminum housing with 18-inch stainless steel armored cable. Floor-mounting hardware included. Universal-style magnet option has a smaller width and depth that provides greater installation flexibility. For normally open or normally closed circuit connection. Wide actuating gap, approximately 3". Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH (in): Magnet: 3.13x0.81x2.13 (79x21x54 mm), Switch: 3.5x1.5x0.44 (89x38x11 mm). Regulatory approvals: UL.
-
Product
8 Relay Output PCIe Board
APCIE-2200-8
-
- 8 electromechanical relays with change-over contacts The PCI-Express 8 relay board APCIe-2200-8 has 8 relay output channels. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
Push Button Controller
Stack-Match II
-
Stack Match controller is a replacement for the rotary switch Stack Match controller. It features pushbutton switches for easy antenna selection and has outputs for both phase control and an auxiliary output. It is a component of the ShackLAN product line and as such can be fully remotely controlled via computer with our ShackLAN Control Center software. All outputs are switched with relay contacts for maximum reliability and power for the external switching unit may be applied from a separate power source to provide maximum isolation from the ShackLAN network. There is also a PTT input to allow different stack configurations for transmit and receive.
-
Product
Non-Contact Displacement Meter
-
The principle of the eddy current is applied to measure the distance without contacting an object. This measuring method is widely used in the industry for detecting abnormal vibrations of rotating shafts or ironwork in a production in line. The highly accurate signal conditioning for providing the analog voltage being linearly proportional to displacement can be made easy.
-
Product
Chilled Mirror Transmitter
DewTrak II
-
The DewTrak II uses the chilled mirror dew point temperature condensation principle to determine the water vapor concentration in gas mixtures, and a platinum resistance thermometer to accurately measure that temperature. Outputs include 4 to 20mA, 0 to 5 Vdc, or 0-10Vdc and an RS232 serial port as well as electrically isolated relay contacts.
-
Product
Chroma Milliohm Meters
-
Chroma Systems Solutions, Inc.
The Chroma 16502 Milliohm Meter is Chroma’s newest digital Milliohm Meter. 0.001mΩ~1.9999MΩ wide measurement range. DC, Pulsed, and Dry-circuit test current driving modes, enable the Chroma 16502 can be properly used in DC resistance measurement for various inductive components (coil, choke, and transformer winding etc.), cable, metallic contact (connector, relay switch etc.) and conduction materials.
-
Product
Voltage Tester Pen
TOB-VT
-
Xiamen Tob New Energy Technology Co., Ltd
Non Contact Voltage Tester Pen For High Voltage Testing. Non-contact AC voltage tester pen has high precision and accuracy, with compact and portable design appearance, and the double plastic shell is to ensure the safety of the users.
