Voltage Regulators
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
SparkFun Breadboard Power Supply 5V/3.3V
-
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
Product
Compact Automatic Voltage Regulating Relay With Built- In TPI
-
NMC’s Microcontroller based Automatic Voltage Regulating Relays (AVR Relays) are latest technology based Relays used for regulating the secondary voltage of Power Transformers with On Load Tap Changer (OLTC). The Parameter settings are made through the front panel keys & are stored in NVRAM. Independent time delays can be set for first control pulse & subsequent pulses. Built-in Tap displays Tap number of Power Transformer. OLTC is blocked for UV, OV, OC, CF, Min/Max Tap Positions & Tap Fail . in manual mode, Tap Raise/Lower can be achieved through front keys. In TEST mode, Relays, Display and LED indications can be checked. A pair of contacts are available for Raise, Lower, UV, OV, Manual Mode, CF, TF & OC. There are two nos. of 5 Amps C.T.’s available, one for the Over Current blocking and L.D.C. & other for measuring the Current.
-
Product
Cycle Voltage Drop (Rise) Simulator
STT-CSS-20P1
-
Beijing KeHuan Century EMC Technology Co,.LTD
*Using 2 The regulator, and the rated voltage adjustable automatic voltage regulator, power fluctuations avoid adversely affecting the test results. Simulate the test under 110V power supply. It can simulate the fluctuation of the power grid under extreme conditions (such as high or low power supply voltage in remote areas).
-
Product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
-
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
Product
Rad-Hard Power Management
-
ST offers a comprehensive range of QML-V rad-hard power management solutions for space applications including linear voltage regulators (low-dropout regulators), point of loads (switching DC/DC converters), PWM controllers, gate drivers, and an industry-unique integrated current limiter.
-
Product
NIM and CAMAC Power Supply
UEP 15
-
The UEP 15 is a plug in power supply for use in UEN 04 bin or for powering every non-powered extant NIM bin. The UEP 15 features all 6 voltages, stabilized by adjustable monolithic voltage regulators. Outputs are ported using a rear mounted NIM connector with a standard NIM pin out.
-
Product
Filament Transformers
-
Osborne designs and produces high impedance and unregulated Filament Transformers. An unregulated filament transformer supplies a specified voltage and current to the filament of an electron vacuum tube. High impedance filament transformers are designed around a tungsten tube filament. Osborne often works with our clients to increase the life-span of their vacuum tubes through the use of a regulated voltage supply.
-
Product
AC Source
5310（0~500Vrms/1KVA）
-
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
Product
Test Bench
BERTA
-
OPAL-RT’s BERTA test bench is a safe, reliable and portable test bench for speed governors, turbines, voltage regulators (AVR) and power system stabilizers (PSS). Equipped with a high-performance real-time simulator programmed with world-renowned RT-LAB software, the BERTA Test bench enables users to easily and comprehensively test real generating units in the power plant, synchronized and transmitting power to the main grid and/or on real controllers connected to a virtual generating unit in laboratory.
-
-
Product
Linear regulated power supply with thyristor pre-regulation
NTN
-
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Miniature Fluxgate Magnetometer
WFG-110
-
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
Product
2KVA Scaler Transformer
T-1005
-
The Titan Series T-1005 Scaler Transformer is used to conveniently scale the standard OV to 130V/260V full scale AC Power Source/Frequency Converter output to 76 different full scale voltages and currents. It is also used to join and scale the power from multiple Titan series AC Power Sources/Frequency Converters into a single output. It has a conservative continuous power rating of 2KVA and excellent voltage regulation.
-
Product
High Voltage SMU 2500 V
AXV7607
-
Generate extremely short, fully regulated voltage pulses of up to 2500 V. Measure leakage currents up to the pA range.
-
Product
SparkFun Breadboard Power Supply Stick
3.3V/1.8V
-
This is a very simple board that takes a 4-9V input voltage and outputs a selectable 1.8V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard.
-
Product
Arduino CAN Shield
IFB-10003-INP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Power Supply PowerLab 305d-ii
-
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated (limited) power consumption and additional output has-voltage. Adjustable outputs can work independently, in series (max output voltage 120V DC for model 605-II) or parallel (max current of 10A for models 305-II and 605-II). Power can be used in the design of electronic products, scientific works, laboratories, production lines and in teaching.
-
Product
Analog Power Supply
Type NPS-2412
-
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Micro-Size Power Supplies
-
Advanced Energy’s micro-size, high voltage DC-to-DC converters offer a variety features — arc limits, tight line and load regulation, voltage monitoring, and more. Get the right solution in the perfect size.
-
Product
Power Supplies
ZP - SERIES
-
Many power supplies fail to obtain the 80-Plus certification, which indicates that the power supply can provide 80% plus power efficiency. The ZP series, however, can. It is one of the few power supplies that can give you the power you need at higher efficiency, which means you can use the same power with less energy. It is also built with a 120mm fan that maximizes its cooling system and Active PFC to improve the stability and efficiency of the transmission network. APFC will help reduce transmission loss and improves voltage regulation. Save money at high power efficiency with ZP.
-
Product
Low Voltage Regulation
-
The low voltage regulation system LVRSys represents a cost effective alternative for grid expansion. The economic use is recommended in all low voltage grids where short-circuit power is sufficient, but have voltage maintenance problems.
-
Product
Dielectric Resonator Oscillators
-
Dielectric resonator oscillators (DRO) are free running oscillators that utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals with excellent frequency stability. In addition, these oscillators are equipped with an internal voltage regulator that further improves the frequency stability by isolating the external bias pushing and modulation. In general, these oscillators are fixed. However, a small mechanical or electrical tuning range can be achieved by use of a self-locking screw or an integrated Varactor diode. The standard offering covers the frequency range of 2 to 40 GHz. While standard models are equipped with female SMA and K connectors at the RF port, other RF interface options are also available.
-
Product
PXI Dual Programmable -10V Power Supply
41-736-001
Programmable Power Supply
A single slot power supply module providing two programmable negative output voltages. It provides high quality regulated voltages from a linear regulator to ensure low levels of output noise.
-
-
Product
Bi-Directional Amplifiers
-
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
Product
Arduino CAN Shield
IFB-10003-AWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Automatic Voltage Regulating Relay
-
NMC introduces low cost microcontroller based basic automatic voltage regulating relay, type : h-101.
