Push Pull Force
stength necessary to press on and extract.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Clamping Force Tester
KRD102
-
KRD102 series clamping force tester is an indispensable test method for improving products into high-quality fields. It is suitable for research, development, quality control and manufacturing of electronics, electromechanical, optoelectronic, automotive, toy, packaging and other industries. It can simulate the situation that the goods in the container are clamped when they are transported from the container to the warehouse. Whether the goods are damaged due to the clamping, so as to evaluate the anti- clamping ability of the packaging.
-
Product
Tactile Pressure and Force Measurement
I-Scan® System
-
This versatile tactile pressure measurement system is tailor-made by choosing from over 200 pressure sensors to meet your specific application requirements.
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
3-Component Quartz Force Links
261 Series
-
Three-component force links eliminate the preload requirement of 3-component quartz force ring sensors, and offers a convenient, 4-screw hole mounting plate on each side end the sensor. Quartz 3-component force links are constructed by installing a 3-component force ring sensor, under preload, between two mounting plates.
-
Product
Ergonomic Force Gauges
-
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges. They are an excellent, low cost solution for tensile or compression testing.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 155gf
K100-K150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Atomic Force Microscope
NaioAFM
-
The NaioAFM is the ideal atomic force microscope for nanoeducation and basic research on small samples. This all-in-one AFM system provides solid performance and easy handling, with a price tag and footprint that fit anyone and any place.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
Compact Hydraulic Vibrator Force Simulator
JF Series
-
The JF Series Force Simulator was developed with the emphasis on light weight, compact size and ease-of-use as a general-purpose, compact jack for the Servopulser system. Testing systems installed with the Force Simulator can easily perform endurance, fatigue and simulation tests on small structural members and various other structural members, which helps improve the logical design and reliability of products.
-
Product
Force Measurement Systems
-
Tekscan's load & force measuring systems answer market needs for an economical test & measurement tool.
-
Product
Industrial Gas Springs – Pull Type
-
If ACE gas push type springs cannot be used due to a lack of space, ACE's industrial gas pull type springs come into their own. These compact assistants with body diameters of 0.59“ to 1.57“ (15 to 40 mm) are effective in the direction of traction and work in the opposite way to the principle of gas push type springs.
-
Product
Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
The force sensors can be integrated easily and uncomplicatedly by the regular standard thread.
-
-
Product
High Power Temperature Forcing System
MaxTC G4
-
NEW G4– MaxTC is our premium Temperature Forcing System product, specifically designed for industry needs as a result of customer´s feedback from the Flex-TC. Its powerful cooling force (90W @ -40°C), rapid transition rates (75°C /min) and remote control capabilities will provide solutions to all semiconductor testing needs. MaxTC is compact, ultra quiet (55 d BA) and fits into any laboratory. A premium product at amazing value.
-
Product
Economic Extreme Power Temperature Forcing System
ECO Cool
-
ECO Cool® Economical Powerful - Thermal Forcing System.Exceptionally Powerful, Economical & Reliable
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Ergonomic Force Gauges
-
AMETEK Sensors, Test & Calibration
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges.
-
Product
IEC60884 Fig20 Flexible Cord Retention Force Test Apparatus
IEC60884 Fig20
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 Fig20 Flexible cord retention force test apparatusMeet the standard: GB2099.1-2008 Article 23.2 and Figure 20, IEC60884 Figure 20, VDE0620 Uses: It is used to check whether the plug wire and the electrical accessory are firmly fixed. Sample range: detachable plug, detachable mobile socket, non-removable plug and non-removable mobile socket
-
Product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplifier
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 230gf
K100-C150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type E, Ø1.50mm, 305gf
K100-E150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style E, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Force Sensor Elements
-
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
Product
ForceTest Force Measuring Software
-
AMETEK Sensors, Test & Calibration
The ForceTest software interfaces directly with your digital force gauge enabling you to automatically capture tests and graphs on a personal computer. Test results and graph can be monitored directly on the live screen in real time while the test is being performed.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
Force Protection
-
The Durham is a high-performance, highly-mobile and easy to emplace Medium Range Day/Night Wireless Surveillance System using a state of the art day camera and a cooled, highly sensitive 640x480 InSb Focal Plane Array thermal camera with 8X continuous optical zoom. The system is image stabilized and has automatic tracking of targets. Each system consists of a Base Station and one Remote Station which can be emplaced up to 5km away for wireless operation or within 500m for fiber optic operation. A single Base Station can monitor and control up to four (4) Remote Stations. The system is powered by a generator, batteries, solar (supplemental power), or vehicle power. Other options available are laser pointers, designators, and a vehicle integration kit.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Snap Button Pull Test Machine
UI-TX01
-
Snap Button Pull Test Machine is used to test pull strength of ornaments on garment, toy, footwear and others including button, bow and etc. Snap button pull test is a must-do test especially for Baby and children’s clothing and shoes. The test aims to use to button snap pull tester with suitable grips to pull the ornament to know if the ornament would be pulled off garment or not. The ornament falling off or broken button may cause infants or children the risk of ingestion. The button pull test methods includes 16CFR1500.51-53, ASTM PS79-96, ASTM F963, EN 71-1，M&S P115A and etc.
