-
Product
ECAT MiniModules
ECAT STGMM 6
-
Precise and synchronous acquisition of mechanical strain directly at the strain gauge points of application: This is what the EtherCAT®-based measurement module ECAT STGMM 6 with six time-synchronous strain gauge inputs for quarter-, half- and full bridges has been designed for
-
Product
Averaging Axial Extensometers for Large Compression Samples
Model 3542RA
-
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
-
Product
Flat One Side Baseplates
BE-FOS
-
Bemcoil-FOS (Flat One Side) is made from 18 gauge, 304 stainless steel sheet combined with 11 gauge (0.120 inch thick), 304 stainless steel plate. Bemcoil-FOS can be circuited to allow tapped or clearance hole penetrations for mounting. This material is sometimes specified as a liquid nitrogen cooled water getter plate material in optical testing systems.
-
Product
Level Meter
LM86
-
Beijing Airport Beiguang Instruments Co., Ltd
The basic version magnetic level gauge.
-
Product
Digital Gauge Pressure
ZET 7012-I-VER.3
-
Digital gauge pressure ZET 7012-I-VER.3 meter is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface.
-
Product
Multi-mode Ultrasonic Thickness Gauge
MMX-6DL
-
The MMX-6DL has all the features of the MMX-6 plus: An Internal data logger that stores a total of 1000 readings in 10 files of 100 readings each file. This gives the user the ability to store, and download the stored measurements directly to a PC using our DakView software program. The software and transfer cable are included in the MMX-6DL kit.
-
Product
Needle Microprobe
MT-29/3HT
-
Fast-response 29 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 3k
40-265-102
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Universal Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Universal Transmitter for temperature, load cells / strain gauge, potentiometer and resistance in 6 mm housing. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
Coating Thickness Gauges
-
Application of coating thickness gauge:used for measuring thickness and corrosion of pressure vessels, chemical equipment, boilers,oil storage tanks, etc. in industries of petroleum, shipbuilding, power station, and machine manufacturing.
-
Product
Manometers
-
Test Products International, Inc.
Single input vacuum gauge. 12,000 to 15 micron measurement range. 300 PSI over pressure. A safer instrument for your job.
-
Product
Force Measurement & Torque Measurement Test Stands
-
Mark-10 offers the industry's most extensive line of manual force measurement and torque measurement test stands. Test stands are useful in eliminating variability inherent in hand testing and can help to automate test processes. A wide range of capacities, loading methods, and configurations are available. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Ultrasonic Testers
-
Our Ultrasonic Thickness Gauge range, is the widest selection on the market with the best cost/performance ratio. On some of the models the warranties are extended up to 5 years while all of these gauges are efficiently and fully backed up and supported. These models are normally carried in stock for fast delivery.
-
Product
Pressure Type Water Level Gauge
HR8003
-
HighReach Measuring & Controlling System Co.,Ltd
HR8003 high-precision pressure water level gauge is a hydrological instrument used for water level and water temperature measurement. It is developed through years of production technology and uses advanced mixed signal processing technology to overcome the shortcomings of traditional analog circuit modules. Full-scale digital Linear correction, full temperature zone digital temperature error compensation; compensation parameters are stored in non-volatile memory.
-
Product
Testing Tensile Strength of Overlays, and Overlayments
James Bond Test ™ MK III
-
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
Product
Ergonomic Force Gauges
MSE100 Series
-
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Height Gauges
V7
-
This Height Gauge 2D combine technological innovation and tradition. With their touch-display and lateral insert holders, the V7 rank as universal instruments for the workshop.
-
Product
Ultra Fine Flexible Microprobe
IT-24P
-
IT-24P Ultra Fine Flexible Microprobe - Tiny, 24 gauge polyurethane coated wire with polyester insulated thermocouple bead. For research applications to measure temperature in animal brains and other tissue. Fairly fragile, but very fast responding.
-
Product
Equator Gauging System
-
The Equator system is a flexible gauge, designed to provide speed, repeatability and ease of use for manual or automated applications, which is why hundreds of manufacturers worldwide are replacing their current gauging method with Equator systems.
-
Product
Coating Thickness Meters
-
PCE Instruments' accurate, affordable coating thickness gauge, thickness meter, surface testing and film gauge devices are used for material testing, manufacturing quality control and automotive paint inspection applications. Choose from a variety of coating thickness gauge, mil gage or paint meter products used for the non-destructive measurement of nonmagnetic coating, insulating layer and dry film thickness (DFT) on ferrous and / or non-ferrous metal substrates such as steel and aluminum.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Shaft Power Measurement Solutions
-
Our marine shaft power meter systems measure shaft torque, power, propulsion, rpm and thrust (if required), to ensure optimum performance is maintained throughout the lifecycle of a vessel. Using highly accurate & reliable strain gauge technology, combined with cutting-edge electronics, our system has an accuracy of 0.1%. It can be installed and commissioned within 1-2 days on a variety of shafts including intermediate shafts, thrusters, propellers and controllable pitch propellers. Our technology, along with our expertise in dynamic sampling of strain gauges, enable us to unlock a significant amount of information regarding the performance of the engine & propulsion shaft, along with the propeller.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 2k
50-265-304
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Mechanical Coating Thickness Gauge
211
-
This is one of the most popular mechanical coating thickness gauges in the world.Factory calibrated - with user calibration adjustmentFoils supplied to check calibration on siteIdeal for cold surfaces and underwater useSmall and portable with an accuracy ±5%The “V” grooved base, ideal for pipeline inspectionAvailable in either Metric or Imperial versions, the Elcometer 211 measures coatings up to 6mm (250mils)
-
Product
Portable Thickness Gauge
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gauge that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
Digital Pressure Gage (DP Gauge)
DP-340 series
-
DP Gauge (Digital Pressure Gauge) DP gauge is the ideal tool for pressure measurements. Excellence in not only being built into a measuring machine or system but using by it self. Downloads data in PC by a high-accuracy measurement and a communication function such as peak HOLD etc are another features. DP gauge comes with an inspection report of a traceability certification
-
Product
Coating Thickness Gauge for Ferrous and Non-Ferrous Materials
CM8856
-
* It meets the standards of both ISO2178 and ISO 2361 as well as DIN, ASTM and BS. It can be used both in the laboratory and in harsh field conditions.* The F probes measure the thickness of non-magnetic materials (e.g. paint,plastic, porcelain enamel, copper, zinc,aluminum , chrome etc.) on magnetic materials (e.g. iron, nickel etc.) . often used to measure the thickness ofgalvanizing layer, lacquer layer, porcelain enamel layer, phosphide layer, copper tile, aluminum tile, somealloy tile, paper etc.The N probes measure the thickness of non - magnetic coatings on non-magnetic metals .It is used on anodizing, varnish, paint, enamel,plastic coatings, powder, etc. appliedto aluminum, brass, non-magnetic stainless steel, etc.* Automatic substrate recognition.* Manual or automatic shut down.* Two measurement mode: Single andContinuous* Wide measuring range and highresolution.* Metric/Imperial conversion.* Digital backlit display gives exactreading with no guessing or errors.* Can communicate with PC computerfor statistics and printing by theoptional cable.* Can store 99 groups of measurements.* Statistics is available.2.SPECIFICATIONSDisplay: 4 digits LCD, backlitRange: 0~1250 μm/0~50mil(other ranges can be specified )Min.radius workpiece: F: Convex 1.5mm/Concave 25mmN: Convex 3mm/ Concave 50mmMin. measuring area: 6mmMin.Sample thickness : 0.3mmResolution: 0.1 μm (0~99.9μm);1 μm (over 100μm)Accuracy: ±1~3%n or 2.5 μm or 0.1mil(Whichever is the greater)Bttery Indicator: Low batter indicator.PC interface: with RS-232C interfacePower supply: 2x1.5 AAA(UM-4) batteryOperating condition: Temp. 0~50℃ .Humidity <95% .Size: 126x65x35 mm; 5.0x2.6x1.6 inchWeight: about 81g(not including batteries)Standard accessories:Carrying case ...................1 pc.Operation manual ............ 1 pc.F probe in built .................1 pc.NF probe in built...............1 pc.Calibration foils ..............1set.Substrate (Iron) ................1 pc.Substrate (Aluminium)......1 pc.Optional accessories: RS-232C cable & software:1.USB adaptor for RS-232C2.Bluetooth interface
-
Product
Digital Gauge Pressure
ZET 7012-I VER.3
-
Digital gauge pressure ZET 7012-I VER.3 (open membrane) is used for fast and simple overpressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface. ZET 7012-I VER3 digital gauge pressure meter is intended for integration into various technological processes automated control systems. Open membrane type enables sensors operation in viscous, pasty and rapidly polymerizing environments.
-
Product
Coating Thickness Gauge
CM8855
-
It meets the standards of both ISO2178 and ISO 2361 as well as DIN, ASTMand BS. It can be used both in the laboratory and in harsh field conditions. The F probes measure the thickness of non-magnetic materials (e.g. paint,plastic, porcelain enamel, copper, zinc, aluminum , chrome etc.) on magneticmaterials (e.g. iron, nickel etc.) . often used to measure the thickness ofgalvanizing layer, lacquer layer,porcelain enamel layer, phosphidelayer, copper tile, aluminum tile, some alloy tile, paper etc. The N probes measure the thickness of non - magnetic coatings on non-magnetic metals .It is used on anodizing, varnish, paint, enamel,plastic coatings, powder, etc. appliedto aluminum, brass, non-magnetic stainless steel, etc. Automatic substrate recognition. Manual or automatic shut down. Two measurement mode: Single and Continuous Wide measuring range and high resolution. Metric/Imperial conversion. Digital backlit display gives exact reading with no guessing or errors. Can communicate with PC computer for statistics and printing by the optional cable. Can store 99 groups of measurements. Statistics is available.2.SPECIFICATIONSDisplay: 4 digits LCD, backlitRange: 0~1250 μm/0~50mil (other ranges can be specified )Min.radius workpiece: F: Convex 1.5mm/Concave 25mmN: Convex 3mm/ Concave 50mmMin. measuring area: 6mmMin.Sample thickness : 0.3mmResolution: 0.1 μm (0~99.9μm);1 μm (over 100μm)Accuracy: ±1~3%n or 2.5 μm or 0.1mil(Whichever is the greater)Bttery Indicator: Low batter indicator.PC interface: with RS-232C interfacePower supply: 2x1.5 AAA(UM-4) batteryOperating condition: Temp. 0~50℃ .Humidity <95% .Size: 126x65x35 mm; 5.0x2.6x1.6 inchWeight: about 81g(not including batteries)Standard accessories:Carrying case ...................1 pc.Operation manual ............ 1 pc.F probe in built .................1 pc.NF probe in built...............1 pc.Calibration foils ..............1set.Substrate (Iron) ................1 pc.Substrate (Aluminium)......1 pc.Optional accessories: RS-232C cable & software:1.USB adaptor for RS-232C2.Bluetooth interface
