Mainframes
Fully capable housing with power, cooling and emi protection ready to operate with the addition of instruments.
-
Product
Mainframe Chassis
DXM/64x64 and DXM/128x128
-
These Chassis provide a non-blocking, full fan-out matrix in any configuration from 16x16 to 128x128 or larger. Both systems are capable of switching high speed differential CML up to 2.5 Gbps but are most commonly used for ECL, LVDS, LVPECL, Spacewire or RS422.
-
Product
Power Supply
-
The Power Supply Systems are the heart of any experiment. They provide the High voltage and Low voltage required by the detectors and by the related front-end electronics. The quality of the power supply is critical to obtain the best performance from the set-up. The sensibility of modern detectors, in fact, make them susceptible to any even small variation in the power supply, and so features like low Noise, low Ripple and high stability become essential in the design of a performing power supply system. Strong of 40 years of collaboration with the most important research labs worldwide CAEN offers today sophisticated High Voltage Power Supply and Low Voltage Power Supply Systems. The demonstration of this successful long-standing tradition is the “CMS Crystal Award 2009” that CAEN received for the development and production of the power system for the CMS tracker. CAEN offers a wide selection of Power Supplies in different form factors and standards:- For smaller set-ups Standalone or modular (NIM / VME) products or are the ideal fit.- For bigger set-ups, where a high number of High voltages and Low voltages is required, the Mainframe Systems and Boards (up to 48 channels/board, up to 768 channels in a single Mainframe) are the most recommended.
-
Product
Switch Mainframe
SW1002
-
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
Single Channel, ±40 V, 100 MHz, 40 NA – 1 A
CX1101A
-
The CX1101A single channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide common mode voltage range. The maximum current can be expanded to 10 A using a CX1206A.
-
Product
Power Supply Mainframe And Modules Instrumentation
-
High power, dual channel PXI User Power Supplies as well as precision DC source instrumentation. These products are offered in both PXI and GTXI formats.
-
Product
Dual Channel, ±12 V, 100 MHz, 40 NA – 1 A
CX1102A
-
The CX1102A dual channel current sensor is a dedicated accessory for the CX3300 series mainframe and features wide dynamic measurement ranges due to the simultaneous capture technology.
-
Product
65 GHz Dual Channel Optical Module
N1030B
-
The N1030B is a plug-in module for the DCA-X mainframe that includes two 65 GHz optical channels.
-
Product
Data Acquisition System
DAQ973A
-
Get the next-generation data acquisition (DAQ) system with a three-slot mainframe and your choice of nine plug-in modules. Interface with the DAQ using Keysight BenchVue DAQ software or use the intuitive graphical front panel with task-oriented, self-guiding menus.
-
Product
Modular Power
RFP AC Power
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
Semiconductor Tester
5000E
-
Current Ranges:Standard: 2.0nA – 50AUp to 100A with Mainframe ExtensionVoltage Ranges:Standard (anode): 10mV – 1000V2000V with 2kV Anode OptionStandard (gate): 10mv – 20V80V with 80V Gate Option
-
Product
Power Analyzers
-
Our line of Digital Power Analyzers offers excellent measurement performance and value for power applicationsAvailable in single channel form or as a four slot mainframe, APS Power Analyzers provide precision power measurements for AC and or DC power measurement requirements. They are a perfect compliment to our AC Source and DC Power Supplies as the offer higher accuracy and resolutions that typically found in T&M power conversion equipment.
-
Product
9 Slot, 3U PXI Express Chassis
GX7600 Series
-
The GX7600 Series mainframes are compact, 9-slot PXI chassis that can accommodate up to 8 instruments as well as an embedded single slot cPCI Express controller such as the GX7944 or a PXI Express external bus controller such as the x1 or x4 MXI - PXI Express interface. The GX7600’s compact 3U form-factor occupies only 9 x 18 inches of bench space, making it ideal for benchtop or space constrained applications. And when combined with 8 peripheral slots, integral Smart functions, and the bandwidth of PXI Express, the GX7600 represents a new level of performance, capabilities and value for PXI mainframes.
-
Product
ATE For ADC Module
MS 1527
-
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Product
Switching Matrix Systems
VX Series
-
The VX Series of low-cost, versatile Switching Systems use a modular concept of Switch Modules,Display Modules and Control Modules which can be assembled into VX/256 Mainframes as Matrices,Multiplexers or Individual Relays.
-
Product
150 Watt Electronic Load Module
N3302A
-
The Keysight N3302A is a 150 W (0-30A, 0-60V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3302A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3302A can also digitize waveforms.
-
Product
16 Channel Mainframe
Synergy CS
-
The Synergy CS mainframe further extends the available channel count supporting up to 16 input modules in a benchtop or rackmount configuration. The Synergy CS can be configured with or without internal display.
-
Product
Powered VXI Crates
6U VXI-C Size High Power Receiver Crate
-
The WIENER high power C-size VXI receiver mainframe is optimized for test applications with demanding power requirements. Up to 6kW DC power can be provided and distributed to the VXI modules.
-
Product
Multi Channel Bit Error Rate Tester
QSFP+ Tester Rx
-
You want to save time by measuring sensitivity on all four QSFP+ channels at the same time? Here we go: BERT + E/O converter + optical attenuator + optical power meter.Have this four times in two mainframes. Only one clock source is needed.Covers 16G FibreChannel and Infiniband FDR.
-
Product
Compact Tunable Laser Source with Continuous Sweep Mode, 1520nm to 1630nm
81940A
-
Keysight's 81940A high power compact tunable lasers enables optical device characterization at high power levels and measurement of nonlinear effects. It's improves the testing of all types of optical amplifiers and other active components as well as broadband passive optical components. As single slot plug-in modules for Keysight's 8163A/B, 8164A/B and 8166A/B mainframes, they are a flexible and cost effective stimulus for single channel and DWDM test applications. Each module covers a total wavelength range of 110 nm in the C+L-band.
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
Product
Single Optical Head Interface Module
81618A
-
The single-channel interface module is used to connect optical heads ( Keysight 8162x ) to the mainframes 8163A/B, 8164A/B or 8166A/B.
-
Product
Powered VXI Crates
6U VXI-C Size 4600 RR Crate Series
-
Designed for high performance automated test and scientific applications. The-RR VXI mainframe series (RR=cooling intake and exhaust at rear side), takes advantage of WIENER’s 50-years experience as a leading manufacturer of powered crates for scientific research and industry.
-
Product
Keysight Switch/Attenuator Driver for 34980A
34945A
-
The Keysight 34945A switch/attenuator driver module for the 34980A Multifunction Switch/Measure Unit allows you to control switches and attenuators external to the 34980A Mainframe. This module provides power and control signals for many of the most popular microwave switches and attenuators.
-
Product
65 GHz Single Channel Optical Module
N1030A
-
The N1030A is a plug-in module for the DCA-X mainframe that can be configured with one 65 GHz optical channel, or one 65 GHz optical and one 95 GHz electrical channel.
-
Product
MPOD HV Module
-
WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which can be mixed in type and parameters. Up to 480 individually controlled high voltage channels are available in one mainframe
-
Product
Accessories For DCA Oscilloscopes Family
N1027A
-
N1027A is a collection of accessories for mainframes and modules in the 86100 family of Digital Communication Analyzers (DCAs).
-
Product
Rack Mount Kit For CX3300 Series
CX1903A
-
The Keysight CX1903A rack mount kit for the CX3300 series lets you easily stack your CX3300 mainframe in a rack.
-
Product
Base Model Custom Configured Modular Power System
N6710C
-
The Keysight N6710C is a 400 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6710C consists of 1 N6700C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6710C.
-
Product
Precision IV Analyzer / 8 Slot Precision Measurement Mainframe
E5270B
-
Keysight E5270B Precision IV Analyzer is the complete solution for current-voltage characterization of a wide range of materials and devices. The E5270B supports multiple SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 0.1 fA. Its modular architecture allows you to configure or upgrade SMU modules for available eight slots. The EasyEXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5270B the best solution for characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency.
-
Product
Universal Multichannel System
-
Power Supply Systems are 100% internally developed and designed to install into a standard 19” relay rack. The mainframes and dedicated HV/LV boards were purposefully designed to provide peak performance in a broad spectrum of operational scenarios and for a vast number of detector types. CAEN mainframe systems are modular, making upgrade and maintenance a breeze.A single mainframe may house and provide control for up to 768 independent channels. Each mainframe may be configured with a mixture of both High Voltage boards for detector bias and Low Voltage boards to drive peripheral electronics.
