Host
-
Product
QSeven
ROM-7510
-
*TI Sitara AM5728 Dual core cortex-A15 1.5GHz high performance processor*Onboard DDR3 memory 2 GB and eMMC Flash 8 GB*Support 1 LVDS, 1 HDMI, 1 USB2.0 OTG, 4 USB2.0 HOST, 1 USB3.0,2 UART, 1 CAN, 1 SATA, 2 I2C, 1 I2S, 2 PCIE 1 lane,*Operating temperature 0 ~ 60 °C / -40 ~ 85 °C*Supports Linux Yocto
-
Product
Framegrabber
FastX1703
-
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
-
Product
3U OpenVPX Multifunction I/O Board
68G5P
-
The 68G5P is a 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. Uniquely designed, the 68G5P provides external access via PCIe x1 and/or SATA II interfaces directly to supported NAI function modules, providing external host SBC function expansion. Additionally, the 68G5P is on NAI’s certifiable product line development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G5P delivers off-the-shelf solutions that accelerate
-
Product
PC Card
MAXPXIe 500
-
The MAXPXIe 500 carrier board is a high performance, modular multi-protocol PXI-Express solution to your tests and simulation requirements, supporting one or two MAX Technologies mezzanine I/O modules. It is powered by a 800MHz RISC processor and 16MB of shared memory, permitting it to buffer and process communication with the host computer.
-
Product
Test Management Software
-
Develop and deploy device tests with a host of software solutions.
-
Product
Active Dual Loop Antenna
KH30936
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
Product
Ultra-High Vacuum Scanning Kelvin Probe
-
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.825-04
-
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PCIe Adapter for PMC
PCIeBPMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
Product
4G Router
ICR-2834G-S1
-
ICR-2800-S1, EMEA, 2× Ethernet, 2× RS232/RS485, USB, GPS, Metal, Without Accessories LTE Cat.4 with 3G/2G fallback. Security based on IEC 62443-4-2 level 1 GNSS receiver 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
4G Router
ICR-2734A01
-
ICR-2700, EMEA, 2x Ethernet, USB, Metal, EU Accessories LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
-
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
Product
NVMe® Technologies
-
We have been a leader and expert in NVMe Testing Services for several years providing conformance and interoperability testing. In addition, we also host NVMe Plugfests where storage vendors from around the world come together to test against NVMe standards to qualify them for the NVMe Integrator's List. The NVMe Integrator's List currently consists of configurations that have proven to be interoperable and conformant to NVMe standards.
-
Product
4G Router
ICR-2734PA02
-
ICR-2700, EMEA, 2× ETH, USB, Plastic, UK Power Supply LTE Cat.4 with 3G/2G fallback. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
4G Router
BB-SR30800310
-
SmartFlex, AUS/NZ, 2x Ethernet, 1x RS232, 1x RS485, Plastic, Without Accessories. LTE cat.4, 3G/HSPA+, GPRS/EDGE, AUS/NZ, 2x SIM. LTE B1, B2, B3, B4, B5, B7, B8, B28, B40. Powerful CPU and Memory, Hosting of SW IoT applications
-
Product
Quad Port Fiber 10GbE Ethernet PCI Express Server Adapter With Intel® XL710-BM1. Ideal For Enterprise Network Infrastructure.
PCIE-2230NP
-
Intel® XL710 Controller4 10GbE SFP+ portsPCIe Gen.3 x8 host interfaceLow profile (half length) form factorsSupports 10GBASE-SR and 10GBASE-LR modulesSupports SR-IOV based virtualization
-
Product
PCIe X8 And X1 Bridge Card
-
The Guzik PCI Express Host Interface Bridge Card was designed to expand the x8 PCI Express Gen 2 (PCIe) slot in a host PC to an AXIe or a Guzik GSA 6000 chassis via a x8 PCI Express Gen 2 and a x1 PCI Express Gen 1 high speed PCI-SIG specified data cables. This allows the end node to connect to the host bus at speeds up to 3.2GByte/sec user data rate. The Bridge Card installs in a x8 or x16 slot of a PCIe backplane or a PCIe motherboard, provides additional board-based retention and reinforced front panel.
-
Product
Multi-Interface Frame Grabber
Xtium2 CXP PX8 Series
-
The Xtium2™-CXP PX8 series is based on the industry standard PCI Express™ Gen 3.0 and CoaXPress ver 2.0 to transfers image data to the host memory at maximum acquisition rates. The Xtium2-CXP series takes full advantage of PCIe Gen 3.0 platform using PCIe x8 slots to deliver bandwidth up to 6.4GB/sec into the host memory while supporting image acquisition from up to 4 CXP12 input channels (12.5Gbps per channel). The Xtium2 CXP series is available in three configurations:
-
Product
NVM Express
-
NVM Express is a scalable host controller interface designed to address the needs of Enterprise, Data Center and Client systems for supporting chip-to-chip, board-to-board, adapter and distance solutions. The protocol can efficiently use interconnect and fabric technologies such as PCI Express, Ethernet and Fibre Channel. Teledyne LeCroy provides protocol analysis, emulation, exerciser and other test equipment to service all NVMe storage applications.
-
Product
Fibre Channel Simulyzer™ Products
-
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
Product
Cloud, Networking & Servers
-
Refers to the hosting or using of network services via a public, private, or hybrid cloud.
-
Product
Dry Film Thickness
-
Dry film thickness, coating thickness or paint thickness as it is often known, is probably the most critical measurement in the coatings industry. It provides vital information as to the expected life of the substrate, the product’s fitness for purpose, its appearance and ensures compliance with a host of International Standards. In 1947, Elcometer launched one of the world’s first non-destructive coating thickness gauges, the Elcometer 101 Coating Thickness Gauge. For more than 6 decades, the design and production qualities of this rugged and reliable instrument have been the watchwords for all our products and these philosophies are still held today. Elcometer has a comprehensive range of Dry Film Thickness gauges to meet all of your coating inspection requirements.
-
Product
CL MX4 Frame Grabber
Xtium-CL MX4
-
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CL MX4 is based on industry standard PCI Express™ Gen 2.0 expansion bus to deliver high speed access to host memory. The new Xtium series offers higher bandwidth to sustain Camera Link® 80-Bit modes over longer cable distances and supports a wide variety of area and line scan color/monochrome cameras, all in a compact, half-length, single slot solution.
-
Product
Network Analyzer N-Port Calibrated Measurements
S95551B
-
PXI vector network analyzers (VNA) offer the capability to extend the number of ports for your measurements by using additional modules. When multiple modules are used, they are configured for multiport operation. The S95551B adds a multiport analyzer mode that enables full multiport error correction and measurement capabilities. The instruments may be identified as one VNA by the firmware running on an external host PC. At least one VNA instrument connected to your PC must have one S95551B license to maintain N-port capabilities.
-
Product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
-
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
LAN Router
BB-SR30000110
-
SmartFlex, Global, 5x Ethernet, Plastic, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
1.3 MP Global Shutter Camera (Monochrome / Color (RAW Bayer))
See3CAM_10CUG
-
The See3CAM_10CUG is a 1.3 MP Custom Lens CMOS USB Global Shutter Camera Module. This is a S/CS/C Mount global shutter camera and is UVC-compliant SuperSpeed USB 3.0 Camera. It is based on the Aptina / ON Semiconductor AR0134 CMOS sensor. See3CAM_10CUG is also backward compatible with USB 2.0 host ports and does not require any special camera drivers.
-
Product
Serial Communication Products
-
Many types of external computer equipment have a serial ports to communicate with host PCs. ACCES I/O has Communication Cards for all of the popular protocols you may find on this type of equipment (RS-232, RS-422 and RS-485), ranging from a single port to eight ports on a single card. There are also optically isolated versions of some of these cards to ensure effective data transmission on long communication lines, even in electrically noisy environments. Having optical isolation is like having data insurance.
-
Product
RS-232 to RS-422/RS-485 Converter
ND-6520
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
USB ASSP
µPD720201
-
The µPD720201 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides four USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
