-
Product
GFS Primary Gravimetric Flow Standard
-
The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.
-
Product
Temperature Loop Control Setup
ULP-27
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Temperature Control Loop Setup is basically a PC based PID controller setup used for closed loop and open loop analysis of temperature process system. The setup comprises of RTD temperature Sensor. The water flows through the Rotameter and Process tank to which a heating coil is fitted. The heater is controlled by a Thirstier drive. The Thirstier drive is connected to PID controller. The manual control valve can control the water flow. The system is mounted on a tabletop model with all necessary Piping. Water at approx. 100 LPH has to be supplied to a system externally. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Turbine Flowmeters
-
Titan’s small turbine flowmeter range use a radial flow principle based on the Pelton wheel technique. This well proven method is the ideal way of measuring low rates of flow of low viscosity liquids. For these mini flowmeters, a jet of fluid is directed at a turbine that is mounted on robust low friction sapphire bearings. The geometry of the turbine and the fluid chamber ensures that the rotational speed of the rotor is proportional to the flow rate through the device. The use of this radial arrangement allows more energy to be imparted into the turbine, so the bearing drag is far less important. Furthermore, because more energy is available the bearings themselves can be a lot stronger so increasing the life of the flowmeter. For larger flows, some of the liquid can bypass the turbine chamber, which then behaves as a “shunt” to the metered fluid. Accuracy is still maintained and the output remains linear.
-
Product
Airlock Control System
-
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
Product
Low-Noise Design
-
* Sound Quality: Find our what your end users like or dislike about emitted noise.* Low-Noise Product Design: Apply interinsically-quiet design principles to your device* Fan Noise: move cooling air quietly* Gas Flows: Reduce noise from industrial gas processes* Advanced analysis and signal processing: Finding the relevant "needle" in the "haystack" of data.
-
Product
Vortex Flow Meters
-
Omega's Vortex Flowmeters measure stem, gas, and low viscosity liquids. The meters offer self diagnostics, low flow stability, high accuracy, no moving parts, and displays flow rate and total flow
-
Product
Ultrasonic Flowmeter
Portaflow C
-
The new Fuji Water Flow C uses the same measurement principle as Fuji's ultrasonic flowmeters of which a great number have already been delivered.
-
Product
Heat Flow Meters
Fox Series
-
Fox Series Heat Flow Meters are reliable, easy-to-use, and durable thermal conductivity measurement instruments. Each of our FOX heat flow meters combines advanced technology with over 20 years of superior engineering. Explore our lineup of thermal conductivity instruments.
-
Product
Massflow Meter
FZ-2200A
-
The FZ-2200A Massflow Meter is Coriolis flow meter that accurately measures the flow of fuels such as gasoline, light oil and kerosene. It is used in combination with the FM-3100 Digital Flow Meter that incorporates the FM-0321 module for the FZ series. The FZ-2200A Massflow Meter is capable of measuring continuous mass flow, making it suitable for the measurement of fuel flow during mode operation, and in-line measurement of fuel density at the same time of mass flow measurement. It can measure fuel consumption from passenger vehicles and medium trucks to large vessels. (As for small flow rate, made to order. Please make sure to check the measurement range when selecting a product.)
-
Product
High Temperature Magnetic Speed Sensors
-
SPECTEC Innovative Sensor Solutions
High temperature speed sensors (up to 454° C) are sensitive, shock resistant & reliable for high temp applications in harsh environments, such as race car engines and transmissions. SPECTEC's high temperature magnetic speed pickups are used as transmission sensors, engine governors, output shaft sensors and flow meter sensors. SPECTEC's high temperature magnetic pick-ups are standard in 5/8-18, 11/16-24 and 3/4-20, and M18 shell sizes.
-
Product
Anemometer
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Digital Wind Speed Air Flow anemometer Temperature Meter Tester
-
Product
Space Flight Components
-
A tec, Inc. specializes in the design, manufacture, and integration of complex test systems and quality critical components. Our production engineering expertise separates us from other manufacturing companies when both reliability and cost are important. Atec has the best in 5 to 9 Axis CNC machining, coordinate measuring machines (CMMs), 3D additive metal and plastic printers, 9-Axis capable waterjet, cryogenic liquid flow test benches and environmental test chambers. We can deliver to the tightest tolerances and most exacting requirements. We can advise our customers on electron beam welding, friction joining, electronic test, environmental test, acoustics, vibration and many other technologies that can reduce manufacturing and operating costs. We are currently manufacturing liquid rocket engine fuel and oxidizer valves for multiple launch vehicles and have participated in 158 consecutive launch successes. Atec manufactured and tested advanced lithium-ion battery adapter plates that manage power for the International Space Station. Atec is designing, manufacturing, and testing power flow modules that work to prevent system failure on the human crew capsule (CCTS) that will transport astronauts to/from the ISS. Atec was awarded NASA Agency-Level Small Business Subcontractor of the Year , SBA Region VI Subcontractor of the Year for our support to NASA and Boeing and we were named a DCMA Top 500 Supplier.
-
Product
Daniel Flow Gauge
2290
-
The Elcometer 2290 Daniel Flow Gauge is a simple gauge used to conduct flow measurement of thick or paste-like materials, such as paints or printing inks.
-
Product
Cement Testing Equipment
-
High quality cement is necessary to produce concrete and mortar that meets relevant construction industry specifications. ELE international designs and manufactures a wide range of sample preparation and cement testing equipment which complies with global standards for the assessment of fineness, consistency, setting time, workability, flow, strength, soundness, heat of hydration and chemical composition.
-
Product
Positive Displacement Meter
-
The Blancett positive displacement flow meter provides high measurement accuracy for fluids over a wide viscosity range. Applications include lubricants, fuels, chemicals and solvents, oils and greases. With only 2 moving parts, the positive displacement meter offers trouble free operation and long service life. The meter is bi-directional and it has an extremely large turndown ratio, up to 400:1 in some models - with full accuracy at extremely low flow rates.
-
Product
Nonwovens Solutions
OptiBond™
-
The capability to monitor and / or control dispensing in real-time helps improve production efficiency and reduce waste. Available as standalone systems or melter-integrated capability, flow monitoring and closed-loop flow control help produce disposable hygiene products faster, more efficiently and at lower costs. Nordson offers a broad range of products to help you improve product quality, reduce material waste, and increase production efficiency. These include: TruFlow meters, dividers / splitters, and applicators. GP 200 remote metering stations, Harmony applicators; Concert flow controllers and VersaBlue Plus or AltaBlue Plus melters.
-
Product
Insulation Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Testing the integrity of insulation requires measuring its resistance to current flow across it. A high level of resistance means that very little current is escaping through the insulation. Conversely, a low level of resistance indicates a significant amount of current may be leaking through and along the insulation.
-
Product
Diode Lasers
-
The large spectral coverage of our diode lasers combined with the compact form factor, direct modulation capability (up to 150 MHz), true off during modulation (>70 dB aspect ratio), and integrated spectral clean-up filters make them ideal for applications in high resolution bioimaging, flow cytometry, optogenetics and quantum technologies.
-
Product
Syringe Pump
65x
-
The 65x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter to 25 mL/min. Exceptional low-flow stability at up to 20,000 psi (1,390 bar) makes this the ideal pump for high pressure applications from deep well core analysis and polymer extrusions. The 65x pumps to the lowest flow rates with zero pulsation available on the market!The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 65x pump module has a single-ratio drive train with autolubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases. Continuous pumping is available in either single or dual pumping system controlled via air valves, offering zero pulsation for unlimited delivery. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
Product
Premier Industrial Shakers
-
The Hardy Shaker ensures that the Seismic Sensors and Transmitters that you have installed are working properly and giving you the results you need. Just like the pressure and flow instruments in your facility need calibration checks every year, so do your Seismic Sensors and Transmitters. This system puts the calibration check of those Seismic Sensors and Transmitters within your control, and within your budget.
-
Product
4FE+1FE SC Multi-Mode Unmanaged Ethernet Switch
EKI-2525M
-
Provides 4 x 10/100 Mbps Ethernet ports with RJ45 connectorProvides 1 x 100 Mbps Multi-mode SC type fiber optic portSupports full/half duplex flow controlSupports MDI/MDI-X auto crossoverProvides redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mount
-
Product
Lake Variable Area Flow Meters
-
Lake Variable Area flow meters, often referred to as rotameters, measure flow rate of a liquid or gas by relating linear displacement of an internal “float” or sharp-edged orifice plate (Lake) to a corresponding flow rate. As flow rate increases, the orifice area that the flow moves through also increases – thus, the term “Variable Area.” Variable Area meters either allow flow through a peripheral orifice formed between a tapered wall and a float as in the traditional rotameter, or an annular orifice and an internal tapered metering pin in the Lake Monitor.
-
Product
Network Monitor & Analyzer
CommView
-
CommView is a powerful network monitor and analyzer designed for LAN administrators, security professionals, network programmers, home users…virtually anyone who wants a full picture of the traffic flowing through a PC or LAN segment. Includes a VoIP analyzer.
-
Product
Portable Servo Conditioners
PTS-V
-
Bemco PTS-V Portable Servo Conditioners provide a closed loop flow of controlled temperature air or gas to an insulated enclosure or structure. Bemco high pressure gas servo conditioners provide air or gas at up to two atmospheres of pressure to heat exchangers and thermal shrouds. Bemco HPG High Pressure Gas Conditioners are described on a separate page.
-
Product
Powered VME64x Crates
6U VME64x 475-x Mini
-
The VME475-x mini crate series offers hot-swappable, redundant power supplies in a 7 slot, compact but modular designed VME64x chassis. A front-side-plug high performance DC fan is used for cooling with front to rear and side to side air flow.
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
Product
Strength Testing
-
Sataton Instruments Technology CO., Ltd
Air permeability tester is professional designed to determine the permeability of materials to air. By testing the rate of flow of air passing perpendicularly through a given area of tested sample under a given pressure over a given time period, the tester can provide results of air permeability performance by calculation the indices. The air permeability testing instrument is applicable to many type of materials, including industrial fabrics, nonwovens, made-up textiles, paper and board, foam and other materials.
-
Product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
-
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
Product
HPLC Pumps
MX Class
-
Further applications include demanding metering and dispensing, as well as Sample Injection, Infusion, or Cone Wash for Mass Spectrometers. Standard fluid path material is Stainless Steel. With flow rates up to 10 mL/min, these pumps can tackle the majority of demanding laboratory applications.Features include pressure monitoring with automatic pressure compensation, Pulse Dampener, integrated Prime-Purge Valve, interactive keypad control, and complete PC control and status through RS-232, micro-USB 2.0, and Ethernet serial communications. Requiring minimal bench space for the performance, the MX Class will easily integrate into most workspaces.
-
Product
DUST CHAMBERS
EDC Series
-
Free-flow dust circulation centrifugal blower.Uniform floating dust simulation across the test space.Dust pre-heating mechanism for free flow of the dust.Hopper re-vibration for free fall of settled dust.Blower speed regulation to ensure metered uniform dust floating inside the test space.Oil-free vacuum pump to simulate negative pressure for IP6X test.Volumetric air-flow meter/counter for IP6X test.View window with illumination.User-friendly Multi-function programmable timer.
