Op Amps
IC used as voltage amplifier. Also known as: Operational Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 26-30 AWG
610138112
Signal Contact (ITA)
Primary mating contact 610138116. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
1000 Amp High Accuracy Current Probe
HA1000
-
The HA1000 is our most accurate current probe. The HA1000 clamp-on current probe measures from 1 to 1000 amps AC.
-
Product
Dual 8-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-002
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-036
Power Patchcord
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 2 Amp, 2m, 250 Port
A500RMR-F-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI 2 Amp Multiplexer, 1-Bank, 64-Channel, 1-Pole
40-657A-001-1/64/1
Multiplexer Module
The 40-657A-001-1/64/1 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of High Density 2 Amp Power Multiplexer Modules available in a choice of configurations, containing up to 8 separate multiplexers, all 1-pole switching. They are suitable for switching signals to 110VDC/250VAC at 2Amps, 90W.
-
Product
48V / 250 Amp Load
BD15-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and is extremely cost effective.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 1m, 250 Port
A500RMR-500RMR-4B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
Amp Booster
CHI680C
-
With the CHI680 Amp Booster, the current can be measured up to 2 A. The CHI680 is compatible with Model 600, 600A, 600B, and 600C series of instruments. You can stack the CHI600/A/B/C and the CHI680 together.
-
Product
30 Amp Fuse Buddy
305M
-
*Fuse Buddy Testers can test circuit current up to 30 Amps. *Two 30 Amp models, #305M used with Mini size fuses and #306B used with ATC size fuses. *Blowing fuses? Get the Fuse Buddy, a great new product. *Clever design allows for easy connection into fuse sockets. *30 Amp models have resolution of .1A, while 20 Amp models have .01A resolution. *Fuse Buddy ends are molded into the shape of the fuse itself. *During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. *The Fuse Buddy stays put and won't fall out of the socket, like test probes do. 305M & 306B Specifications *Tests circuit current from 0 to 30 Amps/48 Volts *Resolution .1A (100 milliamps), accuracy + 2%
-
Product
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 41"
7-242418000-041
Power Patchcord
Mini Power, Receiver, 50u Gold (22 Amps). 18 AWG Twisted Pair Red/Black (5 Amps). Banana Plug Black, Banana Plug Red, 41"
-
Product
3,000 AMP PORTABLE POWER SOURCE WITH JUMP START FUNCTION
VERSAPRO3
-
Shanghai Beha Electronics Co., Ltd.
*Multi-function portable power you can take anywhere*Designed to jump start cars, trucks, motorcycles, boats, ATV’s and more*Vehicle jump starting and device charging capabilities for all of your portable power needs
-
Product
High Accuracy 100 Amp Current Probe
HA100
-
The HA100 is a compact clamp-on current probe for smaller loads where compact size is important. Its measurement range is from 0.1 to 100 amps AC and is very small which is ideal for locking inside a crowded electrical panel during monitoring.
-
Product
500-Pin SEARAY Connector, Male With Backshell, 2 Amp, 250 Port
C500RMR-4SB-4B
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
1000 Amp AC True RMS Digital Clamp Meter
DL6403
-
True RMS reading on AC current and AC voltages provide accurate measurement regardless of the wave form, which makes this the ideal instrument for commercial and industrial applications where no linear loads are present.
-
Product
Carbon Pile Load Tester 500 AMP
6034
-
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector
40-153-003
Relay
The 40/42-153-003 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin SGMC male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
Single 12-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-014
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
PXI 2 Amp Multiplexer, Single 16-Channel, 2-Pole
40-635A-102
Multiplexer Module
The 40-635A-102 is a single 16-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
Product
Quad 2-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-011
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
Signal Patchcord, ITA, TriPaddle, 36", 14 AWG White Teflon, Single Ended, (10 Amps)
7-101914000-036
Signal Patchcord
Signal Patchcord, ITA, TriPaddle, 36", 14 AWG White Teflon, Single Ended, (10 Amps)
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin D-type Connector
40-153-103
Relay
The 40/42-153-103 is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A. User connection is via a 50-pin D-type male connector. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 1 Amp, 0.5m, 500 Port
A500RMR-T-1B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
PXI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
40-635A-106
Multiplexer Module
The 40-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 0.5m, 250 Port
A500RMR-T-5C050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI/PXIe Power Relay Module, 25xSPST, 5 Amp, 50-pin SGMC Connector, With Interlock
42-153-003-HI
Relay
The 40/42-153-003-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Signal Contact (Receiver)
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.
-
Product
PCI 2 Amp Multiplexer, Single 16-Channel, 2-Pole
50-635A-102
Multiplexer Module
The 50-635A-102 is a single 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
