-
Product
Inductor Coils
-
SemiGen's Inductor Coils are manufactured using our thin film process on quartz substrates. The precision photolithography and non-chemical etching process provides clean edges to assure uniformity from coil to coil. By using quartz and applying a polyimide coating we produce a device that eliminates the need for conformal coating or staking. Inductors can be epoxied down with nonconductive epoxy and the wire bonded for connection.
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
Partial Discharge Inductor
Tracy
-
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
Product
Power Inductor
-
Is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.
-
Product
Power Inductor - Impulse Winding Tester
19301A
-
Chroma Systems Solutions, Inc.
The Chroma 19300 Impulse Winding Tester with high/low inductance test technology has 1000V of impulse voltage and a 200MHz high speed sampling rate that satisfies most power inductor test requirements for a wide range of inductance products from 0.1uH to 100uH. The built-in Area Size Comparison, Differential Area Comparison, FLUTTER value, and LAPLACIAN value functions are able to effectively inspect coils for insulation abnormalities.
-
Product
Inductance Standard
1482 Series
-
The GenRad 1482 Standard Inductors are the standard of choice in metrology labs. Used today by national metrology institutes and primary standards bodies around the world, these inductors have no peer or equivlent.
-
Product
Broadband Tuners
BT1500A
-
The BT1500A 1500 watt balanced antenna tuner is the only 1500 Watt, Double-L Network antenna tuner on the market today covering 20m to 160m (2500+/-j2500) and 10m - 15m (1000+/-j1000). The BT1500A features two tandem mounted, precision ceramic roller inductors for a truly balanced tuner.
-
Product
Inductors
-
Murata offers a broad lineup of chip inductors that fit diverse requirements such as compact size, large current, etc. across applications ranging from consumer use to automotive applications that require high reliability. We are also productizing inductors with superior mountability thanks to their SMD type that are suited to specific applications such as high-frequency circuits, power supply circuits, in-vehicle PoC, short-range wireless communication, etc.
-
Product
High Impedance Transformers
-
Osborne high impedance transformers are used to step-up, step-down and isolate voltages in single phase and three phase circuits. A properly designed high impedance transformer can be used an an equivalent to an isolation transformer connected in series with an inductor. The high impedance characteristic may be employed as a current limiting feature in both the primary and secondary circuity.
-
Product
Power Supply Designer
-
Combines the ICAP/4Windows Power Deluxe tool suite (above); Magnetics Designer for the design and synthesis of all types of transformers and inductors; and Library Manager parts management system.
-
Product
Bias T's
-
Centric RF offers Coaxial Bias T's so that a DC voltage can be applied to the rf signal path. These Bias Tee's (aka bias t) currently are offered with sma and 2.92mm connectors. Bias T's are implemented by attaching a broadband inductor to the circuit trace, with the power rating of the bias tee being determined by the size of the inductor.
-
Product
Precision Impedance Analyzer (20Hz to 10MHz)
ST2839
-
ST2839 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. Its basic accuracy of 0.05%, the fastest test speed of 5.6ms, the frequency range of 20Hz-10MHz, and the impedance test range of up to 1GΩ can meet the testing requirements of components and materials, especially for low-loss (D) capacitors and high-quality Measurement of Factor (Q) Inductors. The four-terminal pair port configuration method can effectively eliminate the influence of the electromagnetic coupling of the test line, and expand the lower limit of the low-impedance test capability ten times lower than that of the conventional five-terminal configuration instrument.
-
Product
Molded Inductors
-
Molded inductors are constructed by pressing or molding a magnetic material around a pre-wound coil and lead-frame to form the inductor. Our molded inductors provide a fully shielded, high energy density, soft saturation solution for applications up to 110Apk. The construction enables low profile solutions in a cost effective and robust solution that minimizes acoustic noise. We offer a high saturation current series (commercial and automotive, -40C to 125C) and a low DCR series (automotive, -55C to 155C) in a wide range of platforms from 4x4x1.2mm up to 24x24x13mm.
-
Product
Digital Power Modules
-
Renesas' digital PMBus power modules integrate a PWM controller, inductor, power MOSFETs, and passive components into one small package making the design of high efficiency, compact and intelligent power supplies easy.
-
Product
LCR Meter
SS10X Series
-
LCR Meters are basic passive component testing equipment, can be used in quality management department or production process for quality inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, electric valve, contactor, cable, wire, etc. This series LCR meter, offering different kind of testing fixtures, can improve testing precision and reduce the difference value of error code, being an economical and useful basic testing instrument.
-
Product
Network Probe for TC-NT2
TC-TP1
-
TRENDnet´s TC-TP1 is an easy-to-use amplified inductor and tone probe that is used for tone tracing and line testing. The TC-TP1 features a simple push button that provides easy operation and conserves battery power. This ergonomically designed device comes with adjustable volume control and signal LED for enhanced accuracy in noisy environments.
-
Product
32 Channel Pass Through Card
SET-2090
-
The input signals can be configured by customers. Each input channel can be tested, conditioned or measured in different ways. Various inductors, filters, pull-up or pull-down resistors can be used for this purpose. In standard configuration, the input signals are transmitted directly to the output.
-
Product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
-
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
-
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
µModule Isolated Transceivers
-
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
Product
Saturable Reactor Inductors
-
Osborne Saturable Reactors are designed to provide a variable output voltage through the use of variable impedance connected in series with a constant impedance load. Each saturable reactor’s impedance is determined by the application of DC power to a control winding. As the level of power supplied to the control winding is increased, the saturable reactor becomes more saturated. This reduces the impedance of the AC gate winding, and increase the amount of the supply voltage that is transferred to the load. Conversely, as the power is reduced to the control winding, the reactor becomes less saturated, the gate winding has more impedance and less of the input voltage is provided to the output impedance. This approach provides excellent quality, reliability, and control when designed to match the requirements of a specific application.
-
Product
50Hz-100kHz LCR Meter
11022/11025
-
Chroma Systems Solutions, Inc.
0.1% basic accuracyTransformer test parameters (11025), Turns Ratio, DCR, Mutual Inductance0Hz, 60Hz, 100Hz, 120Hz, 1kHz, 10kHz, 20kHz, 40kHz, 50kHz, 100kHz test frequencies21ms measurement time (≥100Hz)Agilent 4263B LCR Meter commands compatible4 different output resistance modes selectable for non-linear inductor and capacitor measuringHigh resolution in low impedance(0.01mΩ) and high accuracy 0.3% till 100mΩ rangeAdjustable DC bias current up to 200mA (constant 25Ω) (11025)1320 Bias Current Source directly control capability0.01mΩ ~ 99.99MΩ wide measurement range (4 1/2 digits)Dual frequency function (11022 option) for automatic productionBIAS comparator functionComparator function and 8/99 bin-sorting functionPass/fail judge result for automatic productionHandler interface trigger edge (rising/falling) programmableTest signal level monitor functionStandard RS-232, GPIB, and Handler I/FOpen/short zeroing, load correctionLabView® Driver
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
-
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
EMC Testing Inductors
-
Electromagnetic Compatibility (EMC) testing is a somewhat unique discipline within the world of electrical product development and analysis. Electromagnetic Compatibility (EMC) testing is primarily concerned with understanding and mitigating the affects of Electromagnetic Interference (EMI).
-
Product
Supply Chain Management
-
200 Customers100 Active SuppliersPurchasing for 60 material classifications including such materials as:a) IC, Resisters, Capacitors, Wire, Cable, Power Suppliesb) Connectors, Converters, Diodes, Fuses, Fabricated partsc) Inductors, Relays, Switches, Hardware
-
Product
Harmonic Trap Inductors
-
Osborne designs harmonic trap inductors to work in conjunction with capacitors in power systems to prevent specific line-frequency harmonics from flowing back to the power source (point of common connection). This power quality design approach prevents harmonic currents from flowing to the main facility power system and/or to the utility power system. The Osborne system also reduces unnecessary power losses and power-system pollution.
-
Product
Drum Core Inductors
-
Drum core inductors are so named as the conductor (round magnet wire) is wound directly onto the ferrite core which is shaped like a drum or spool. The wire is then connected to the core, a plastic base or metal lead frame to form the surface mount termination. Drum core inductors come in unshielded (high saturation current but potentially more EMI) and shielded constructions (lower saturation current but closed magnetic path for lower EMI). The shielded constructions use either a second ferrite core or a magnetic resin epoxy to create the magnetic shield.
-
Product
Chip Inductors AECQ200 Compliant
-
Bourns products include surface-mount chip inductors, power chokes, chip beads, chip bead arrays, as well as radial-leaded and axial-leaded inductors. These components are used in computer, communication, instrumentation, industrial, and medical applications.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
-
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
