Microprocessor
an IC processing logic operations to fulfill an end. Also known as: CPU
See Also: Computer, Raspberry Pi, SBC, CPU
-
Product
Microprocessor Development System
DS-M8
-
# Real-Time and Transparent In-Circuit Emulator# Supports PIC12xxx, PIC14xxx, PIC16xxx, PIC17xxx and others# Uses Microchip Bond-Out Technology# Maximum Frequency Support# Standard 64Kx16 Emulation Memory# 32Kx48 Real-time Trace with Filters and Triggers# 64K Hardware Breakpoints with External Signals# Memory Mapping Capabilities# Software for MS-Windows# Source-Level Debugger for C and Assembler
-
Product
Microprocessor Based Indicator
-
Strong Anodized NEMA4X-IP56 ALUMINUM 1/8 DIN CASE Compact Design Provides Excitation to Transducers or Sensors Accept DC mV/V, V, mA Signal Proportional Analog Output V or mA Easy to Program using 4 ButtonsFront Panel Shunt Calibration User Programmable High & Low Set Point Standard No-Output or Relay Output Optional 8-Step Output, RS232, or BCD Output Available
-
Product
Microprocessor Development System
DS-85
-
* Real-Time and Transparent In-Circuit Emulator * Windows Debugger - Update 2009 * Symbolic Debugger compatible with Intel Object Files * 64K Hardware Breakpoints * 64K of Internal Memory * 32K x 32 Bit Trace Memory and Logic Analyzer with External Probes * Serially linked to IBM PC or Compatible Hosts * On-line Assembler and Disassembler * Source and Listing Windows
-
Product
Medical Computer Equipped With MXM Graphics Module Supporting NVIDIA Quadro® GPU With 8th/9th Generation Intel® Core™ I7/i5/i3 In LGA1151 Socket. Compliant With IEC 60601-1/IEC 60601-1-2
MLB-3000
-
- Medical grade computer compliant with IEC 60601-1:2005 + A1:2012 + A2:2020 (3.2 edition) / IEC 60601-1-2:2014 + A1:2020 (4.1 edition)- ADLINK MXM Graphics module support (Type A/B, up to 120W)- 8th/9th Gen Intel® Core™ i7/i5/i3, Celeron® processor- Dual SODIMMs for up to 64GB DDR4 non-ECC memory (dependent on CPU)- DisplayPort (2 from CPU, 4 from MXM)- 1x M.2 E key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 B key supporting 2242 or 2280 for SATA storage module- Reliable Molex type 12V DC-in connector- 1x Intel® i219-LM and 3x Intel® i210-AT
-
Product
RE Family SOTB™ Process-Based Energy Harvesting Embedded Controllers
-
The RE Family based on Renesas' innovative SOTB™ process technology realizes ultra-low current consumption in both active and standby mode and fast operation at low operation voltage, which is impossible to achieve with a conventional bulk transistor. The energy harvesting controller and 32-bit CPU also enable the development of intelligent and battery maintenance-free energy harvesting IoT devices.
-
Product
Hydrostik Data Logging Digital Hydrometer
CTL-200
-
The CTL-200 Hydrostik is a digital microprocessor controlled battery test instrument that replaces the traditional, potentially inaccurate, 'paper and pencil' methods previously used. It can be used on either Vented Lead Acid or NiCad Cells. REMEMBER - never mix electrolytes, it kills batteries!
-
Product
cRIO-9041, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
786369-01
-
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9041 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
-
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
Product
High Impedance Busbar Differential Relay
MIB
-
The MIB, a member of the M II family of economical and highly functional digital protection relays, is a microprocessor based relay that provides three phase high impedance differential protection for Substation Bus-bars of any voltage level. Use the MIB also to protect electrical machines like transformers, generators or motors against restricted earth faults.
-
Product
Multimedia Modular
DPX-M1270
-
Rugged Logic box design, Security and access to meet the requirements of the gaming industry. Intel® 8th/9th Generation Core™-i7/i5/i3 CPUs 8,6,4,2 core. Supports 3 display outputs (2 x DP++, HDMI).
-
Product
Compact 3U CPCI Processor Board
CP32110
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Atom™ x5/x7 E3900 series (Apollo Lake-I), Pentium® N4200 and Celeron® N3350 CPU, CP32110 is a compact 3U CPCI single board computer compliant with CompactPCI® specification.On CP32110, there is a Mini SATA interface for system software installation, and several peripheral interfaces include SATAII, USB2.0 and Giga bit Ethernet.
-
Product
3U CompactPCI-Serial
-
Advantech offers 3U CPCI-Serial CPU blades, I/O blades and AC/DC power modules to build up solutions in railway, semiconductor, healthcare markets.
-
Product
Computer-On-Module
CM12001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM12001 integrates the complete functionality of vertex86DX,offering a CPU, system BIOS, 16bit DRAM up to 512MB, keyboard controller, real-time clock, and IDE compatible onboard Flash hard disk up to 16GB. The solution includes a highly integrated embedded CPU chip made by DMP. It has x86 Compatible Processor Core.This module is designed for embedded applications. The pin out of its’ Dimm-pc bus connector corresponds in large part to the pin out of a standard ISA bus. It offers peripheral functions such as USB, PS2, LPT, COM interface...
-
Product
Standard Tap Position Indicator
-
NMC,s Tap Position Indicator is a Microprocessor based specially designed instrument used to indicate the Tap Position of the Power Transformer with On Load Tap Changer.
-
Product
ACPI Regulators/Controllers
-
Renesas provides complete ACPI-compliant power solutions for the efficient handling of power consumption in microprocessor and computer applications.
-
Product
Industrial PC/104-Plus AMD LX800 x86 Single Board Computer
PPM-LX800-G
-
The PPM-LX800-G is a highly integrated, industrial PC/104-Plus single board computer (SBC) designed for embedded, space-limited, low power applications. It is a full-featured SBC that includes an AMD LX800 x86-compatible CPU, CRT and flat panel video controller, 10/100 Ethernet, two USB 2.0, 16 lines of digital I/O, and four COM channels on a single 3.6 x 3.8 inches (90 x 96mm) module.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
mSATA SSD Carrier
SD3-GLISS
-
SD3-GLISS fits into any CompactPCI® Serial peripheral slot that is PCIe enabled. Hardware RAID operation is supported, running with an enhanced ARM-based processor to offload the host CPU.
-
Product
Force Gauge
-
Tension & compression capability .* 5000 g, wide capacity, highresolution, high accuracy, highrepeatability.* 3 kind display unit, g/oz/Newton.* Separate sensor.* Peak hold ( Max. load ) measurement.* Positive or reverse display direction.* Hand held & stand mounting.* Microprocessor circuit & exclusiveload cell transducer.
-
Product
Master And Slave
Smart I/O
-
An I/O server is a software which controls and monitors one or more PLCs /RTU's using various communication protocols.Our I/O servers are built on highly optimized Windows 32bit platform. They are capable of handling very large scale SCADA systems with minimal impact on CPU usage, resulting in effective timing and usage of available hardware.Currently, we have Master and Slave solutions for DNP3 and Modbus (ASCII, RTU, TCP). Please select the appropriate tab above for more informaiton.If you are looking for a specific I/O Server, please contact us with your needs.
-
Product
CTEK LITHIUM US Battery Charger
56-926
-
The LITHIUM US is an advanced microprocessor controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries - maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
-
Product
Hybridization Oven
REXMED ROV-201
-
MOD. ROV-201, AC 110/230V, Plug type: , Hybridization oven, HS CODE: 841780, UNCCS CODE: 484352, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~85˚C, Stability at 37˚C: ±0.1˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 1.2KW, Shaking timer: 999/min, 999/hr, shaking timer can be set in second, minute or hour function and at the end of operation audio and visual warning, Motor: Noiseless powerful brushless induction motor 15W, Rotation: 5~60rpm adjustable, Rotator: for 8pcs(optional), Orbital: 20~250rpm adjustable, Platform: L30 X W20cm, Chamber: L35 X W25 X H42.5cm, Capacity: 37.2L, chamber with glass viewing window, Optional: Rotator for 8pcs X 1set
-
Product
Relay Testing System
UNO
-
With high power outputs package in an extremely compact and rugged system, the UNO has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
Product
LAN Router
BB-SR30000110-SWH
-
SmartFlex, Global, 5x Ethernet, Plastic, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
LAN Router
BB-SR30009110-SWH
-
SmartFlex, Global, 5x Ethernet, PoE PD, Plastic, Without Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
cRIO-9043, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller
785620-01
-
1.30 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, -40 °C to 70 °C, Kintex-7 160T FPGA, 4-Slot CompactRIO Controller - The cRIO-9043 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 160T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
Radar Scan Conversion Package
SoftScan
-
Curtiss-Wright Defense Solutions
This embedded computing radar product portfolio provides ultra-high radar scan-conversion performance using unique graphics processor unit (GPU)-accelerated algorithms. Utilizing the power and performance of today's modern COTS graphics offerings, SoftScan provides unrivalled scan conversion performance with minimal CPU utilization.
-
Product
Universal Military Craft Systems Controller
3U VPX
-
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
Product
Opacity Monitor
DT109
-
The Datatest Model 109 is a microprocessor based non-compliance opacity monitor for process, baghouse, combustion and OSHA applications. The micro controller provides excellent accuracy, reliability and stability with features such as push button calibration, path length correction and averaging.
-
Product
cRIO-9038, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller
783850-02
-
1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, and Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9038 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9038 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9038 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
