Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends
A050DF4-C-0A050
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m, HV
A009DM5-T-HA050
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Tracing
Tone and Probe
-
The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation. It allows for pin point identification even in the most congested cable bundles. Our unit can be used with any tone generator.
-
Product
Time-Domain Reflectometer
TDR-410
-
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
-
Product
MIPI SLIMbus
-
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
Product
Gauge Type T Thermocouple Wire
W-TW-26
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Tinned Ends, 20A, 1m
A020AFR-T-2A100
-
This is a 1m long female to unterminated 20-Pin Scorpion cable assembly with tinned ends constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
G12 Slide Mount
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
Auto Circuit Tracer
7411
-
Peaceful Thriving Enterprise Co Ltd
Find short and open circuits quickly and easily in DC circuits from 6-42V. Designed to identify and trace wires or cables without damaging the insulation.
-
Product
Adjustable Press Plate Bed of Nails Testers
Rand Adjustable Family
-
esigned for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 2m, 45º
A1604F5-T-0A200
-
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
PXI RTD Simulator Module, 20 Channel, PT500
40-263-102
-
The 40-263-102 is a 20-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Cable Assy 9-Pin D-Type, F/F, 0.5m
40-970-009-0.5m-FF
-
The 9-Pin Female connector option of this cable assembly is suited for direct connection to corresponding Pickering Interfaces products, and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
Sensors
-
Advanced Thermal Solutions, Inc.
ATS designs a range of sensors for more accurate measurement of air and surface temperatures and air velocities. The different models allow data to be obtained in many conditions, including tight spaces and narrow planes. ATS sensors work exclusively with our ATVS family of hot wire anemometer systems.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Away From Pin 1
A050DF4-C-HA100
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Voltage And Continuity Testers
-
Unlike voltage testers, continuity testers are always used when a circuit is turned off—or on wiring or devices that are disconnected from the circuit. They don't test for the presence of voltage but rather to see whether an electrical path is intact in an appliance or a device.
-
Product
Process Tachometer
TCT101-3ABC
-
The Process Tachometer TCT101-3ABC is a panel mount Process Tachometer which can measure frequency up to 100Khz with Encoders and 2 or 3 wire proximity switches. There is also a function to store the maximum frequency and the lowest frequency.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 1m, HV
A037DF4-C-HA100
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
20-Pin GMCT Female Connector, 10A, Without Backshell
92-960-020-10A-F
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
180V-260V AC Socket Tester (For UK)
1941
-
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*LED indicators & Digital display.*Test for 180-260VAC circuit.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 4W*Frequency: 50Hz
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 1m, Spring Latch
A068SFR-F-5B100
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends
A050DM5-T-0A200
-
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-037-0.5m-MU
-
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 2m
A068SFR-F-5A200
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Demagnetize Bar Tube Or Wire Material Ranging Up To 8.5” (215mm) Diameter During Production
Demagnetizers
-
*Offers effective demagnetizing even for problem alloys.*Used in metal manufacturing plants to eliminate residual magnetism in test material after the eddy current test (ECT) is completed.*Can also be used for similar applications where high-speed reduction of residual magnetism is required.*Several models are available to meet your unique production needs.*Experienced MAC® Field Engineers can recommend the most appropriate demagnetizing equipment for your applications.
-
Product
Steady State Chamber
-
Burnsco Environmental Test Chambers
Swivel castors with brakesWelded series 304 stainless steel interior and exterior.Interior light and viewing windowNon-settling, high temperature, fiberglass insulation.Fast response, nichrome wire heating elements.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends, 0.5m, Screwlocks
A068SFR-T-6B050
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
Automatic Upset Testing Machine
YQA Series
-
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
Product
Net Toner and Probe Kit
1EA680
-
Cable tracer is designed to trace wires without damaging the instalations and much more.
