Wiring
See Also: Wiring Analyzers, Trailer Harness Testers, Harness
-
Product
Control Cables
-
TRIUMPH specializes in cable controls which are mechanical connections between controls and actuation systems used in a variety of applications. Our systems provide higher reliability, lighter weight, and greater control box selection. Current controls include wire rope, push-pull controls, sliding friction controls, ball-bearing controls and low-resistance and backlash mechanical control system cables. Wire Rope Controls: Wire Rope is used in applications where weight is critical, and the system operates in tension only. Assemblies are built to your required standards with unlimited configuration capabilities. Sliding Friction Controls: High load capacity in tension and compression. Flexible in any direction, wide temperature range and easy installation. No adjustment or lubrication needed during the life of the control. Ball Bearing Controls: Ball Bearing controls are a self-contained system that performs linear motion under tension or compression loads.Precise and accurate movement with high load capacity offering weight savings, low friction and high efficiency. Quick disconnect ends available.
-
Product
Interior Temperature, Humidity Transmitter
T3318
-
For exacting interiors in building energy management and HVAC systems. Are designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
-
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Primary Test Equipment
LET-400-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
-
Product
Wire Crimp Pull Tester (Manual)
WT3-201
-
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
-
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Tinned Ends, 1m
A015DM5-T-0A100
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks.
-
-
Product
Distributed Data Acquisition
-
Distributed Data Acquisition seamlessly networks all the components of your integrated monitoring system. The resulting synchronization decreases the quantity and lengths of communications wires between sensors and the data-acquisition system (DAQ).
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-C-HA050
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Immersion Temperature Probe
TP47…
-
Series of Pt100 4 wires and Pt1000 2 wires immersion temperature probe.
-
Product
Universal II Level System
-
The Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.
-
Product
RMI Test Panel
TA-1070
-
This is an RMI tester built to duplicate the original model 970E-1 unit. The panel is laid out just like the 970E-1 with an additional interface for our TA-568 to allow distance testing on the BDI-36 RMI. This panel incorporates both SIN/COS and 3 wire synchro outputs. With the use of our TA-900 API the bootstrap and other synchros can be aligned.
-
Product
Primary Test Equipment
LET-2010-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
-
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
Cable Tester
LW3310
-
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
Product
Hot Wire Ignition Tester
-
The HWI test indicates a materials resistance to ignition when exposed to abnormally high temperatures resulting from a component failure such as a conductor carrying far more than its rated current. HWI performance is expressed as the mean number of seconds required to ignite a specimen when wrapped with an energized non-chrome resistive wire that dissipates a specified level of energy.
-
Product
3-Pin Power D-Type Cable, Female to Unterminated, Ferrules, 1m
A003PF4-F-5A100
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Digital Micro Ohm Meters
-
Is used to measure DC low resistance through 4-wire method. Its features are: Comparison function to determine if the device is in good condition, unkown wire length calculation (FT/M); two-way data transmission by USB interface.
-
Product
Terminal Test Kit (19 PCS)
3604
-
Peaceful Thriving Enterprise Co Ltd
1. Checks voltage on 6, 12 and 24V systems.2. 12-feet flexible rubber wire with spring relief.3. Tough plastics handle lights up if circuit is good.4. 4mm connection for banana plugs.5. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
-
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Cable Assy 25-Pin D-Type M/M 2m
40-970-025-2m-MM
-
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 25-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Tool, Locator, Mini Coax, 24 AWG Wire
910104128
-
Used with Crimp Tool p/n# 910101118 to crimp 24-26 AWG wire to mini coax ITA contacts.
-
Product
Cable Assembly, 26-Pin D-Type, Female To Unterminated With Ferrules, 1m
40-972-026-1m-FU
-
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks.
-
Product
Cable Assy 68-Pin SCSI Micro-D M/F 1m
40-970A-068-1m-MF
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Terminal Test Kit (92 Pcs)
3601C
-
Peaceful Thriving Enterprise Co Ltd
*Total: 92 pcs*Alligator clip x 2 pcs*Testing probe x 2 pcs*Flat terminal x 48 pcs*Testing needle x 4 pcs*1 to 2 connector x 2 pcs*Round terminal x 24 pcs*5K variable resistor x 2 pcs*Polarity tester/stroboscope x 2 pcs*SRS air bag replacement connector x 2 pcs*Male / Female to Male / Female Extension Wire x 4 pcs
-
Product
Solid State Synchro Control Transformer and Solid State Resolver Control Transformer
SCT-RCT Series
-
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
Product
Safety Light Curtain Type 4
SF4B Ver.2
-
Panasonic Industrial Devices Sales Company of America
The SF4B Series offers flexibility and a wide range of accessories such as mounting brackets and extension cables. Cables for Series connection are also available to eliminate dead zones. The SF4B Series can now be equipped with corner mirrors to reduce setup work and wiring.
-
Product
Remote I/O
-
Reduces wiring costs, simplify troubleshooting and minimize downtime with Omron's high density I/O modules and other socket-based I/O products.
