Communication
The transmission of data from one computer to another, or from one device to another. (sbc.webopedia.com)
See Also: COMM, Communication Protocol, Spacewire
-
Product
Control Center
COSYMA
-
COSYMA is the control centre for APCOS®4000, consisting of a comprehensive and versatile application software that includes the following components:*Communications Network Control (CNC)*Radio & Device Control (RDC)*Secure Automatic Military Message Handling System (SAMMS)
-
Product
FREQUENCY DISPLAY UNIT
TYPE NFD-1
-
The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.
-
Product
4FE+1FE ST Single-Mode Unmanaged Ethernet Switch, ATEX/C1D2, -40~75℃
EKI-5525SI-ST
-
Communicates with SCADA software via Modbus/TCPCommunicates with NMS (Networking management system) via SNMPPort-based QoS for deterministic data transmission-40~75°C operating temperature range (EKI-5525SI/SI-ST,EKI-5525MI/MI-ST only)8.4~52.8 V DC wide-range power inputEMS level 3 protection for extreme outdoor environmentsIEEE 802.3az Energy Efficient Ethernet (EEE)Supports redundant 12~48V DC power input and P-Fail relayLoop detection
-
Product
HART Modules
-
These Data Acquisition modules communicate over the HART protocol. HRT-370 is a HART signal filter specially designed to solve the issue that analog signal gets interfered while additional HART signal adding to communication process. When connecting HRT-370 to a HART instrument, it splits the input HART signal to two output channels. The I-87H17W is a HART analog input module. It can measure 4~20mA current and act as a HART master, allowing communication with HART field devices. Its user-friendly design saves a lot of work when measuring current due to a built-in resistor.
-
Product
Wireless Connectivity Tester
CMW270
-
The R&S®CMW270 is the ideal test solution for integrated wireless communications solutions as used in laptops, netbooks, game consoles, data cards, wireless headsets and other products of the IoT market. Within the R&S®CMW500 - Production Test product family, the R&S®CMW270 offers functionality tailored to the above applications. The tester provides network emulation (signaling mode) for WLAN and Bluetooth® as well as generator and analyzer functionality for standards such as WLAN, Bluetooth®, GNSS and broadcast technologies.
-
Product
Industrial Data Communications
-
The specialized networking systems, protocols, and hardware used to connect machines, sensors, and controllers on a factory floor or in a plan.
-
Product
Microohmmeter
MMR-6700
-
The MMR-6700 digital meter is designed for measuring low resistances with a stabilised current of up to 200 A. The use of test clamps enables the safe measurement of breakers (high-, medium- and lowvoltage), isolators and other components earthed on both sides. The MMR-6700 series meters are equipped with a unique module in their class that measures inductive components which have a current of up to 10 A, enabling the winding resistance of motors, transformers and other inductive components to be measured. Another useful function is the temperature measurement and the automatic compensation of results with relation to the measured temperature or temperature set by the user. The system is completed with a recorder function. Special measuring algorithms and additional functions allow an appropriate measuring method to be chosen depending on the measured component and measurement conditions, thus, widening the application areas of the meter. The state-of-the-art user interface, various communication interfaces, wireless communication and communication with the computer, printer, 2D code reader are integrals features which enable full, comfortable and intuitive management of not only measurements and their results but also ID data of measured components.
-
Product
3U cPCI Sensor Interface Unit
SIU35
-
NAI's SIU35 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU35 uses up to five NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-To-Mission."
-
Product
Micro-Ohmmeters
RMO-G Series
-
The RMO-G is a portable micro-ohmmeter designed for contact resistance measurement of non-inductive test objects and applications with increased safety requirement. It tests medium and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. Due to its Both Sides Grounded and Remote Control functionalities, the instrument accurately measures even in the most demanding environments, providing additional safety to testing personnel.The RMO800G is the most powerful portable micro-ohmmeter on the market with 800 A output current. RMO200G is our best seller in the USA. A user can choose the appropriate model depending on the output current requirement, from 100 A (RMO100G) to 800 A (RMO800G).We use an unbreakable plastic case with IP67 protective rating (with closed lid) for instruments’ housing. Although very portable and lightweight, RMO-G micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents. Consequently, it enables the usage of thinner/longer test cables. RMO-G generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. During the testing, it increases current before measuring and decreases current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.Special current clamps measure a current through groundings when the instrument tests in Both Sides Grounded conditions. The instrument itself powers these clamps. If even higher safety level is required, the Remote Control feature enables the operator to perform measurements from distant locations.RMO-G instruments can store up to 500 measurements in internal memory. Also, they have a built-in thermal printer and USB flash drive available as an option. An additional option is the built-in High Precision module suitable for measurement of very low resistance, in the range from 1 to 30 µΩ, with 0,01 µΩ resolution.Our free DV Win software communicates with the RMO-G micro-ohmmeters via USB or RS232 interface. It allows a user to run the test remotely from a PC. Also, a user can download test results, analyze and generate fully configurable test reports through the software.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - PCIe
Model 78660
-
Model 78660 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, high-speed data converter, it issuitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture features offer an ideal turnkey solution.
-
Product
Interconnect Products
-
Typical industrial applications for Oxley Interconnect products include high voltage power supplies, critical computer hard drives, fire safety control equipment, medical and pharmaceutical equipment, oil and gas control systems, power generation and distribution equipment, rail and telecommunications infrastructure. Within aerospace and military markets Oxley products are typically found in aircraft, military vehicles, ground base stations, surface ships and submarines and air and ground communications equipment.
-
Product
ARM-based Single Board Computer
IC-ARM-VPX3b
-
Designed for applications requiring high processing and communication performance and low power, the IC-ARM-VPX3b is a highly versatile SBC for small, 3U OpenVPX systems. The IC-ARM-VPX3b is developed in alignment with the SOSA™ Technical Standard.
-
Product
MultifunctionAsync Serial Communications Adapter
2628
-
The Multifunction RS422/RS485/Digital I/O board provides a collection of various interfaces on a single-wide PMC module. The two 16550 UARTs on the board provide asynchronous communication at bit rates to 115Kbaud. The 16550?s are mapped into host processor space so that standard drivers can be used with the board.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Network Analysers
-
DIN 96x96 ultra compact version, only 39 mm depthFully bi-directional four quadrants measurements for all energies and powersMain electrical parameters measured and displayed for a cost-effective consumption analysisVersion for 1 or 5A CT and for direct connection up to 6APossibility to connect by PTUp to 8 MB for data recording (ENH version)Possibility to record all energy counters (ENH version)Up to 24 parameters selectable among real time measurements for MIN/AVG/MAX recording (ENH version)MODBUS RTU/ASCII communication by RS485 port or MODBUS TCP communication by Ethernet portPossibility to manage the instrument in remote mode by WintoolNET software or by Web server interface2 digital outputs, 1 digital input, 1 analog output (optional)
-
Product
QDRII/DDRII/ QDRII+/DDRII+ SRAM
-
DDR II / II+ (Double Data Rate) SRAMs and QDR^(TM) II / II+ (Quad Data Rate) SRAMs are the ideal memory devices for next generation networking and communications systems. These ultra-fast devices can support high bandwidth systems that require memories capable of very high operating frequencies combined with low latencies and full cycle utilization.
-
Product
Ocean and River Instruments
RINKO-FT (ARO-FT)
-
The RINKO FT not only retains the fast response time identical to that of conventional RINKO series but also has greater accuracy and stability by incorporating high-quality multipoint calibration and improved sensing method. This instrument is primarily designed to target Argo float operations,however, its compact, lightweight, and commonly used communication protocol widen the choice of platforms for installation. The RINKO FT allows DO measurements with a high vertical resolution, which will contribute to the understanding new aspects of physical/biochemical processes.
-
Product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
RF Upconverters
-
SignalCore offers traditional multi-stage and single-stage RF upconverters, and Direct IQ modulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF upconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in point-to-point radio, wireless communication, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
-
Product
FMC Wideband RF Transceiver AD9371 Based
FMC-ZU1RF-A
-
Sundance Multiprocessor Technology Ltd.
The FMC-ZU1RF-A is a FMC for RF wireless communications applications based on the AD9371 component from Analog Device Inc (ADI).http://www.sundance.technology/wp-content/uploads/2018/01/FMC-ZU1RF-High-Res-Cutout-e1516095831285.jpgThis FMC is fully hardware and software compatible with the ADRV9371 evaluation board from ADI.
-
Product
Full W-Band Power Amplifier
SBP-7531142515-1010-E1
-
For communication and radar applications, SAGE Millimeter has released a new full W-Band power amplifier. Model SBP-7531142515-1010-E1 is a power amplifier with a typical small signal gain of 25 dB and a nominal output power of +15 dBm across the frequency range of 75 to 110 GHz. The DC power requirement for the amplifier is +15 VDC/190 mA. The mechanical configuration offers an in-line structure with WR-10 waveguides and UG-387/U-M flanges. Other port configurations, such as with 1 mm connectors or a right angle structure with WR-10 waveguides, are also available under different model numbers. Features include: Full Band, High Gain, High Output Power.
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
Multi-Function Power Transducer
TD2418B
-
The TD2418B is a micro-process based transducer with a 16 bits CPU (Center process unit) and equipped with full-digitized measuring, calibrating and output functions.TD2418B not only can take the place of several static con-verters and measuring instruments (V, A, W, PF, VAR, WH, VARH, Hz) by single unit, but also have some special function such as Maximum measuring, Minimum measuring and comparator output. In communication, we use the most convenient and the easiest RS232 or RS485 as our standard output port, besides, we adopt Modbus Protocol, one of the most popular protocol in the world, as our standard protocol.
-
Product
MTCA.4 Power Supply
-
To match the requirements of the next generation of “carrier grade” communication equipment the PCI Industrial Computer Manufacturers Group PICMG created in 2002 a new standard AdvancedTCA / ATCA. The ATCA crate backplanes are based mainly on 48V industrial power supplies. From this form factor evolve the Advanced Mezzanine Module carrier card AMC form factors defined in AMC.3 in types of single or double width.
-
Product
20KVA to 200KVA Industrial UPS (3Ø – 3Ø)
NSP Series 20KVA to 200KVA
-
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
Product
Omnidirectional Antennas
-
In radio communication, an omnidirectional antenna is a class of antenna which radiates equal radio power in all directions perpendicular to an axis (azimuthal directions), with power varying with angle to the axis (elevation angle), declining to zero on the axis.[1][2] When graphed in three dimensions (see graph) this radiation pattern is often described as doughnut-shaped. Note that this is different from an isotropic antenna, which radiates equal power in all directions, having a spherical radiation pattern. Omnidirectional antennas oriented vertically are widely used for nondirectional antennas on the surface of the Earth because they radiate equally in all horizontal directions, while the power radiated drops off with elevation angle so little radio energy is aimed into the sky or down toward the earth and wasted. Omnidirectional antennas are widely used for radio broadcasting antennas, and in mobile devices that use radio such as cell phones, FM radios, walkie-talkies, wireless computer networks, cordless phones, GPS, as well as for base stations that communicate with mobile radios, such as police and taxi dispatchers and aircraft communications.
-
Product
Compact & Robust Tunable Laser
WSL-110
-
Designed for use in fiber optic transmission testing, our WSL-110 can also be used for DWDM component evaluation and coherent communications testing. The WSL-110 features grid tuning and gridless tuning options, allowing any wavelength to be accessed.
-
Product
Permanent Noise Monitoring System
831-NMS
-
The Model 831-NMS permanent noise monitoring system is designed for long term monitoring around airports, industrial facilities, motorsport complexes, wind farms, mining operations, and within the general community. Many required accessories are integrated through the INT docking station. Two way remote communication is available for monitoring and control from a central station. Larson Davis provides the hardware, software and open interface to allow this system to be customized for any application or purpose.
-
Product
MXI-Express Cable, Gen 2 x8, Copper, 3m
782317-03
MXI Express
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
