Counting
-
Product
Multi-Channel Analyzer
-
The MCA1K is a compact multi channel analyzer (MCA) for processing gaussian inputsIt is capable of sorting input pulses from shaping amplifiers into 512 discrete bins.Each Bin can record up to 16M counts before an overflow event occurs.
-
Product
Optical Probes - Low Bandwidth
P6701B/P6703B
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.- Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm- High-bandwidth DC up to 1.2 GHz- High Gain 1 V/mW- Low Noise <11 pW/√Hz- Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series- SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
FastBrake®
-
FastBrake® Electronic Air Brake is a microprocessor based, electro-pneumatic braking system. Designed for superior reliability, the system includes tightly integrated electronics and pneumatics, redundant electronics, dual channel power supply, and reduced part count. With over 4,100 systems installed globally, FastBrake® is service-proven and backed by Wabtec's global service and support network.
-
Product
PXIe-4140, 4-Channel Source Measure Unit
781742-01
-
The PXIe-4140 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4-wire) sensing for accurate measurements. The fast sample rate of the PXIe-4140 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules.
-
Product
Alpha/Beta Counters
-
ORTEC offers a full suite of MANUAL alpha/beta counters incorporating either gas-flow proportional detector or dual-phosphor scintillation detector technologies. These manual, single detector systems are ideally suited for applications requiring long count times for a small number of samples.
-
Product
High Accuracy Mini Digital Multimeter
HH2109
-
High Accuracy (Basic Accuracy 0.7%). LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A
-
Product
3GHz 16-Channel Signal Generator 19" 3U Rack Module
LS30816R
-
The LS30816R, 3GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS30816R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS30816R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
Product
Time History Recording to Throughput Disc
-
For the most critical tests time history data can be recorded in parallel with vibration control with no reduction in control performance. The real-time throughput data capture function of the m+p VibControl system allows you to record all selected channels continuously in the time domain on the embedded data server (“throughput to disc”) irrespective of the channel count and the frequency range utilized. This means that you can always access all the original data for analysis purposes.
-
Product
PXI Very High Density Multiplexer, 2A, 79-Channel, 2-Pole, Multiple Channel Mode
40-611B-002-M
-
The 40-611B-002 (PXI) and 42-611B-002 (PXIe) modules are 79-Channel 2-Pole multiplexers. A 158-Channel 1-Pole configuration is also available. They use high quality electro-mechanical signal relays allowing switching up to 2 A and voltage up to 300 VDC/240 VAC. They are suitable for signal routing in high channel count ATE and data acquisition systems. Connections are made via a front panel 160-pin DIN 41612 connector.
-
Product
PXI-2533 , 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-33
-
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2533 is a high-density 4x64 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2533 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
-
Product
PXI-2596, 26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module
778572-96
-
26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module—The PXI‑2596 is an RF signal multiplexer switch with dual 6x1 multiplexer banks in the same module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use the PXI‑2596 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
Saluki SFS-2000 Fusion Splicer (4 motors)
-
SFS-2000 series is the new standard 4 motors fusion splicer. Light Weight, Touch Screen, Friendly UI, Fast Fusion and Heating, makes it very popular and hot.* 7s fast splicing, 14s highly efficient heating* 320/88 times image magnification, 5mm fusing for ultra-short cleave length* 10000 groups of fusion records storage* 300 groups of splice modes, 100 groups of heating modes* 220 counts of splicing and heating cycles with build-in 6800mAh Li-on battery
-
Product
Counter DAQ Cards
-
Counter card series include pulse output, event counting, PWM measurement/output and encoder reading functions.
-
Product
PXI BRIC8 FIBO Matrix Dual 186x4 2pin brkout
40-592A-116
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
Intelligent Digital Multimeter, Calibrated, 3999 Count, Mean Value, Auto, Manual Range, 3.75 Digit
72-7755 CAL DU
-
The 72-7755 CAL DU from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
Product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, 10MHz RS-422 Inputs
APCIE-1711-10MHZ
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications can be realised through software adaptation.
-
Product
PXI 3A Power MUX BRIC, 12-Channel, 16-Pole
40-571-204
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI BRIC8 FIBO Matrix Dual 40x4 3pin brkout
40-592A-102
-
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units.
-
Product
Digital Multimeter
MY68
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Multimeter digital 1999 counts display with holster Frequency capacitance digit analog bar graph MY68 V&A.
-
Product
Cluster Series Systems
-
The quadrupole analyser is a precision assembled triple mass filter with unique, independently driven RF only secondary filter stages preceding and following the primary mass filter. A UHV low profile electron impact ioniser with twin oxide coated iridium filaments and a pulse ion counting single channel electron multiplier detector are included as standard. A Faraday detector option extends the dynamic range to 5 x 1010.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
-
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
Handy Size Digital Multimeter
HH2107A
-
Basic Accuracy 1.0%. Large LCD display 2000 count, 21mm figure height. Manual Ranging at your choice (19 Range). High Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 20MΩ
-
Product
Process Counter
CT6000
-
Full-logic control process counter.• Displays process, batch, total, and rate• Optional relay outputs and/or 4-20 mA analog output• Completely field adjustable• Full diagnostic functions• 3 programmable transistor setpoint outputs and inputs• Bi-directional counting• 115, 230 VAC (50-60 Hz) and 10-30 VDC power options
-
Product
USB-6363, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device
782258-01
-
32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device - The USB‑6363 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6363 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
TPI With Counter
-
Our Digital Tap Position indicator with Counter Display is used to indicate the Tap Position of the Power Transformer with On Load Tap Changer as well as also indicates the counts of the tap changer.
-
Product
Handheld Digital Multimeter, Compact, 3999 Count, True RMS, Auto Range, 4.75 Digits
72-9380A
-
A premium, compact hand-held digital multimeter that boasts a 39999 count display and an optically isolated USB interface.
-
Product
VFD Dual-display 4 1/2-digit Digital Multimeter
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital multimeter TH1941 4 1/2-digit is voltage/ current /resistance tester with multi functions and low cost. The instrument can stably perform measurement at high speed as several times as other instruments at the same level. It provides excellent performance, such as maximum reading of 12,000 counts, maximum DC voltage accuracy of 0.02%, and low cost to give you a best choice. Having VFD dual-display with high brightness. TH1941can synchronously display measurement parameters, such as AC/DC voltage or current, AC voltage/current and frequency to improve measurement efficiency and display results clearly.
