DAQ Systems
Sense, log and store information.
-
Product
System Test Fixture
-
Chassis Level Test Fixture, Set Box Test Fixture, and more by IST Engineering
-
Product
Loss Measuring System for Transformers
LiMOS
-
HIGHVOLT Prüftechnik Dresden GmbH
The transformer loss measuring system LiMOS is designed for highly accurate measurement of losses and other parameters required in the framework of routine and type testing of power transformers. The combined voltage/current sensors and the digital signal processing enable a very compact design with only one HV device per phase with smallest volume and footprint. The digitized and preprocessed signals are transmitted via fiber optic cable to the receiver unit (LiMO-MCSU).
-
Product
Data Acquisition System
Pixie-16
Data Acquisition Module
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
Product
RF Plasma Power Systems
-
These are ideal solutions for plasma apps like etching, cleaning, deposition and more
-
Product
Diving Technology Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
Product
GC And GC-MS Application System
Py-GCMS
-
Pyrolysis gas chromatography mass spectrometry (Py-GCMS) can be used to characterize most materials including insoluble and complex materials at trace levels often without any sample pretreatment e.g. polymers, plastics, rubber, paints, dyes, resins, coatings, cellulose, wood, textiles, oils etc.
-
Product
Transverse Planer Moisture System
MC PRO 2400
-
Maximize grade recovery with Finna Sensors' highly accurate transverse planer meter. The most widely-adopted transverse sensor system acts as a dropout or easily integrates with auto graders. Integration via ProTrac software, with barcode or manual tracking, provides advanced kiln analysis and drying reports.
-
Product
X-Ray Inspection System
TruView™ Cube
-
The Perfect Solution for a Powerful Small Form Factor X-ray Inspection System. The all new TruView™ Cube X-Ray Inspection System is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. Ideal for applications where space is premium, the the TruView™ Cube X-Ray sits comfortably on your laboratory bench.
-
Product
Custom Systems
-
Due to many years of experience in the development and manufacturing of signal transmission equipment in different frequency ranges and with various functions, we are able to design special systems that are completely tailored to your needs.
-
Product
Full Indoor Radio System
CFIP Marathon II
-
CFIP Marathon 300 MHz / 1.4 GHz point-to-point long-haul microwave system is the perfect solution for industrial applications where fiber is not available. Primarily designed for remote and rural areas Marathon Full Indoor Unit can establish a link in adverse weather conditions and over long distances, frequently exceeding 100 km. SAF Tehnika Marathon solution is particularly recommended for utility (electricity, water), oil & gas, public safety, and transport companies who are looking for reliable data & voice transmission.
-
Product
Tan Delta Test System
-
Precision measuring bridge is designed for determining the capacitance and dielectric dissipation factor of liquid and solid insulants, cables, capacitors, line transformers, generators, motors, bushings etc. Furthermore it can also be used for power loss measurement on shunt reactors or similar apparatus. This system is suitable for both low and high voltage measurement at line frequency. Measurement reports can be printed. This measuring equipment has been specially developed to maximise efficiency in production and quality control environments. Its outstanding accuracy also makes it suitable for laboratory and research applications.
-
Product
Chromatography System
ACQUITY UPC2
-
With the ACQUITY UPC2 System, the orthogonal capability of normal-phase LC has been elevated to a mainstream technique: *Convergence Chromatography. The chromatographic principles and selectivity of normal-phase LC *The ease-of-use and method development simplicity of reversed-phase LC *The use of gradients across the widest polarity range *Chiral and achiral separations in one system, with unequaled speed and confidence
-
Product
CrystalCalHP Calibration System
-
AMETEK Sensors, Test & Calibration
This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It allows you to do a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate.
-
Product
Attitude Heading Reference System
M&M Modules
-
PNI’s M&M modules will self adapt and learn its system and its environment automatically to provide accurate quaternions, heading, pitch and roll. All while using 100 times less power than traditional AHRS modules.
-
Product
Weight Registration System
-
The number of the current hopper and the correct positioning, along with the indication of power and status, are displayed on the indicators. Four load cells are mounted on the cart. The system records the amount of material shipped from each hopper, and the total weight of the material in the trolley is also displayed. All information is stored in the controller memory for a specified time. After the necessary time intervals, the operator can rewrite the information on the USB drive for further processing.
-
Product
Robotic and Computer Programming System
Sense
-
Sense is a robotic and computer programming system which allows users to explore, problem solve, and advance their computer programming abilities from just starting in visual block programming, to Python and C languages.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Contact Resistance Measurement System
CRMS
-
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
Product
Photochemical Pollution Monitoring System
-
Are large-scale air quality models that simulate the changes of pollutant concentrations in the atmosphere using a set of mathematical equations characterizing the chemical and physical processes in the atmosphere.
-
Product
Manual & Automatic Inspection systems
-
Manual and Automatic inspection systems mounted on vehicles such as motortruck, van, railway testing wagons etc. Operation is either on the move or during a stop. Ideal for inspecting transmission and distribution lines and for electric transportation.
-
Product
Matrix Code Verification Systems
REA MLV-2D
-
The REA MLV-2D is a matrix- and barcode verifier which has been developed in conformance to international standards. The measurement uses defined angeles distance and illuminations to achieve repeatable results and quality information.
-
Product
Network Management System (NMS)
-
Schweitzer Engineering Laboratories, Inc.
An NMS is a software application (or set of applications) that provisions, monitors, and maintains communications networks.
-
Product
Classroom AV Systems
-
Solutions for classroom AV, voice amplification, and campus communications.
-
Product
Automated Thermal Stress System
ATSS Series
-
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
Product
Video Quality Analysis Systems
ClearView Extreme 8K and 4K Systems
-
Highest Resolution Video and Audio Quality Analyzers with 12G-SDI Interfaces and ST 2110 Networking Option
-
Product
CT Inspection System
FF35 CT
-
The YXLON FF35 CT computed tomography system is designed to achieve extremely precise inspection results for a wide range of applications. Available in a single or dual tube configuration, it is perfect for very small to medium size parts inspection in the automotive, electronics, aviation, and material science industries.
-
Product
Probe System for Life
PS4L
-
The Probe System for Life, or PS4L, is SemiProbe’s patented adaptive probe system architecture. Unlike traditional probe systems, all of the basics components of our systems, including the bases, stages, chucks, microscope mounts, and manipulators, are interchangeable, upgrade-able, and configurable. The PS4L Adaptive Architecture ensures and optimal test configuration for each individual customer application.
-
Product
Wireless System For Test And Measurement
TM400 Compact
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
Autoanalysis System Set
PGA-710B
-
The PGA-710B is a unique electrostatic data analysis device for use with Prostat's PFK-100B Field Meter and Charge Plate Monitor kit. It records, plots, analyzes and automatically constructs reports of body voltage generation, electrostatic decay, voltage retention, ionizer performance and other static measuring functions.
-
Product
ATE System Integration
-
Cyth Systems is a Systems Integration Company specializing in Automated Test (ATE), Embedded Controls, and Machine Vision. Our skilled and experienced team uses their natural talent for problem-solving to create solutions in a wide range of industries. We build our solutions starting with the National Instruments (NI) platforms including LabVIEW and PXI, and by adding best-in class sensors and components.
