GHz Synthesizers
See Also: GHz
-
Product
Mixed Signal Oscilloscope: 25 GHz, 4 Analog Plus 16 Digital Channels
MSOV254A
-
25 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
-
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
Product
Power Limiter, DC to 6 GHz, APC-7
11930A
-
The Keysight 11930A limiter provides input protection for a variety of RF and microwave instrumentation. For example, the input circuits of network analyzers may be protected for inputs up to 6 watts peak or 3 watts average power using the Keysight 11930A.
-
Product
PXI Solid State Dual SP4T Switch Module, 50 MHz To 20 GHz
M9161D
-
The Keysight M9161D PXI Dual SP4T solid state switch module provides an ultra-long cycle life, fast switching speed and high isolation, all within a single slot enclosure.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP8T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-788-021-TE
-
The 40-788-021-TE (PXI) and 42-788-021-TE (PXIe) are single failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Multi-Channel Attenuation Control Unit (4-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7204B
-
The J7204B is a multi-channel (4-channels) attenuation solution for signal attenuation and conditioning of up to 4 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7204B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Oscilloscope, 8 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8080HD
-
Oscilloscope, 8 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-031-E
-
The 40-784B-031-E (PXI) and 42-784B-031-E (PXIe) are single failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-121-TE
-
The 40-788-121-TE (PXI) and 42-788-121-TE (PXIe) are single failsafe SP10T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
USRP‑2930, 20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device
781910-01
-
20 MHz Bandwidth, 50 MHz to 2.2 GHz, Included GPS-Disciplined OCXO, USRP Software Defined Radio Device - The USRP‑2930 is a tunable RF transceiver with a high-speed analog‑to‑digital converter and digital‑to‑analog converter for streaming baseband I and Q signals to a host PC over 1 Gigabit Ethernet. It also features a GPS-disciplined oscillator (GPSDO) with PPS accuracy of ±50 ns. You also can use the NI USRP‑2930 for the following communications applications: white space; broadcast FM; public safety; land-mobile, low-power unlicensed devices on industrial, scientific, and medical (ISM) bands; sensor networks; cell phone; amateur radio; or GPS.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
W-band Transmitter (94 GHz, 50 MW Output Power)
-
W-band Transmitter (94 GHz, 50 MW Output Power)
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-021-E
-
The 40-781A-021-E (PXI) and 42-781A-021-E (PXIe) are single failsafe SPDT 18 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-780B-542
-
The 40-780B-542 (PXI) and 42-780B-542 (PXIe) are dual failsafe SPDT 40 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
-
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
Product
Oscilloscope, 16 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8160HD
-
Oscilloscope, 16 GHz, 80 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 6 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-002-E
-
The 40-784B-002-E (PXI) and 42-784B-002-E (PXIe) are dual failsafe SP6T 6 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
3 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 3 Ports
GPS302
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
RF Power Splitter, Combiner, Divider IP67, 3 Way, SMA Female, 2.4 - 6.0 GHz
PD2568
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (20 dB avg)Excellent VSWR (1.25 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
-
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz.
-
Product
FieldFox Handheld Microwave Signal Analyzer, 50 GHz
N9962B
-
A lightweight, durable, software-enabled, microwave signal analyzer, interference analyzer, distance-tracking generator, preamplifier, power meter, and more.
-
Product
Frontend - Frequency Extension to D-Band (110 GHz to 175 GHz)
FE170ST
-
The R&S®FE170ST is ideal for early subterahertz and 6G research. By extending the frequency ranges for the R&S®SMW200A and R&S®SMM100A to the D band (110 GHz to 175 GHz) engineers can access the range they need and develop the next generation of mobile communications. The easy-to-use, fully-calibrated solution is compatible with our signal generator, analyzer and oscilloscope environments. Plug it in and start designing the next generation of mobile communications today.
-
-
Product
IC-3121, 1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller
784961-01
-
1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller - The IC‑3121 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3121 offers two USB3 ports with dedicated bandwidth, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
-
Product
Adapter, 1.0 Mm (m) To 1.0 Mm (f), DC To 120 GHz
Y1910C
-
Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
USB Coaxial Switch, DC to 8 GHz Dual SP6T
U1816A
-
The Keysight U1816A is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
Product
2 GHz Dual 1:4 RF Mux, 50 Ohm Module for 34970A/34972A
34905A
-
The Keysight 34905A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
Surface Mount Frequency Synthesizers
-
Corech Surface Mount Frequency Synthesizers series packs impressive low phase noise of -90dBc/Hz@1kHz, low spurious of -50dBc to -70dBc, high temperature and corrosion resistance, long operating life, temperature uniformity, and good thermal conductivity. These outstanding performance make it suitable for high-reliability and environmentally stressful applications including communication systems, test and measurement equipment, radar systems etc.
