GHz Synthesizers
See Also: GHz
-
Product
Modulation Distortion Up To 13.5 GHz
S930701B
-
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Oscilloscope 50 GHz, 4 Channels
UXR0504B
-
UXR0504B Infiniium UXR-Series is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
Product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 6U VPX
Model 57841
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with one 3.6 GHz, 12-bit A/D- Two-channel mode with two 1.8 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
-
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Differential Active Probe, 1.7 GHz
DP0013A
-
The Keysight DP0013A is the 1.7 GHz model of the DP001xA Series differential active probes. These provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
90/120 GHz Dual Channel Optical Module
N1032B
-
The N1032B is a plug-in module for the DCA-X mainframe that includes two optical channels up to 120 GHz.
-
Product
26.5 GHz Or 54 GHz, Up To 4 GHz BW, RF PXI Vector Signal Transceiver
789600-08110
-
The PXIe-5842 is a vector signal transceiver (VST), which combines a vector signal generator and vector signal analyzer into a single four-slot PXI Express instrument. This VST provides the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5842 benefits from PXI modularity and scalability, as up to four PXIe-5842 VSTs can fit into one 18-slot PXI Chassis. Additionally, the VST provides the error vector magnitude (EVM) performance required to test a variety of cellular and wireless standards such as Wi-Fi 7 and 5G NR. The PXIe-5842 supports frequency coverage and bandwidth availability for a wide range of semiconductor, aerospace, and defense applications.
-
Product
Multifrequency Clock Synthesizer - PMC
Model 7190
-
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
Product
5-Port Coaxial Switch, DC to 18 GHz
8764B
-
Frequency range DC to 18 GHzUnterminated multiport coaxial switch with five RF portsInsertion loss: < 0.20 dB to 2 GHz, < 0.5 dB to 18 GHzSWR (through line): < 1.1 to 2 GHz, < 1.2 to 12.4 GHz, < 1.3 to 18 GHzIsolation: > 90 dB to 18 GHzLong life > 1 million cyclesHigh repeatability: < 0.03 dB typicalCurrent interrupts and position indication capability
-
Product
26.5 GHz Or 54 GHz, Up To 4 GHz BW, RF PXI Vector Signal Transceiver
789601-26201
-
The PXIe-5842 is a vector signal transceiver (VST), which combines a vector signal generator and vector signal analyzer into a single four-slot PXI Express instrument. This VST provides the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5842 benefits from PXI modularity and scalability, as up to four PXIe-5842 VSTs can fit into one 18-slot PXI Chassis. Additionally, the VST provides the error vector magnitude (EVM) performance required to test a variety of cellular and wireless standards such as Wi-Fi 7 and 5G NR. The PXIe-5842 supports frequency coverage and bandwidth availability for a wide range of semiconductor, aerospace, and defense applications.
-
Product
Frequency Doublers To 12 GHz
-
Pulsar Microwave Frequency Doublers utilize Schottky diodes in a bridge configuration to accomplish the frequency doubling. The input frequency operates from 0.2 to 6000 MHz. Frequency Quadruplers are also available using using this topology. Designs are matched to 50 Ohms and are available in a wide variety of package styles, such as plug-in, flatpack, and connectorized housings. Miniature surface mount packages are the most popular style, and are readily available on tape and reel for use in automated assembly applications.
-
Product
2-Ch. 6.4 GHz or 4-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 6U VPX
Model 58141
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Supports VITA-49.2 VITA Radio Transport standard- Two-channel mode with 6.4 GHz, 12-bit A/D- Four-channel mode with 3.2 GHz, 12-bit A/D- Programmable DDCs (Digital Downconverters)- Four 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- µSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Bi-Phase Modulators To 12 GHz
-
BPSK Modulators modulate an input signal by 0° and 180° phase shifts by injecting a ± 20 mA control signal at port D1.
-
Product
Hybrid Power Divider, 2 GHz to 26.5 GHz
87304C
-
The Keysight 87304C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
Product
InfiniiMax Probe, 1.5 GHz
1130B
-
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
Product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
-
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
Product
2 To 18 GHz 6 Channel Downconverter
-
Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.
-
Product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58741
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1-channel mode with 3.6 GHz, 12-bit A/Ds- Two or four 2-channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one- or two-channel DDCs (Digital Downconverters)- 4 or 8 GB of DDR3 SDRAM- µSync clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
DC Block, 700 kHz to 50 GHz
N9399F
-
The Keysight N9399F DC block offers a new level of DC blocking with performance specified from 700 kHz to 50 GHz. This DC block features a broad frequency range, excellent return loss, very low insertion loss and excellent temperature stability.
-
Product
18 GHz Differential TDR/TDT Probe Kit
N1021B
-
Connect PCBs and other devices without connectors to TDR/TDT modules in the oscilloscope mainframe
-
-
Product
Coaxial Termination, DC to 50 GHz
85138B
-
The Keysight 85138B is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138B has a 2.4 mm female connector.
-
Product
Oscilloscope - 1 GHz, 4 Analog Channels
DSOX4104A
-
1 GHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Power Limiter, 0.01 to 18 GHz
N9356B
-
The N9356B power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.
-
Product
Spectrum Analysis, Up To 70 GHz
S930907B
-
The S930907B spectrum analysis (SA) adds high-performance microwave spectrum analysis to the N522xB/N524xB PNA family up to 70 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Simultaneous spectrum measurements can be done using up to five test and reference receivers. This multi-channel SA can be used with the internal swept-signal generators for efficient measurements of spurious signals emanating from mixers and frequency converters. The SA application employs source-power and receiver-response calibration as well as fixture de-embedding, providing in-fixture and on-wafer spectrum measurements with the highest level of accuracy.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Modulation Distortion Up To 8.5 GHz
S930700B
-
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Waveguide Harmonic Mixer, 40 to 60 GHz
11970U
-
The Keysight 11970U waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
Product
Infiniium UXR-Series Oscilloscope: 50 GHz, 4 Channels
UXR0504A
-
The UXR0504A is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 32 GHz
N9960A
-
5 kHz to 32 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 7.1 lb. (3.2 kg)
