Receivers
Equipment that is the sink or terminator of any signal on a transmission medium. (atis.org)
See Also: ITA
-
Product
ICE 3000 Series
ICE3006
-
The ICE3006 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in the cosite environment. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the three-port design (LOS and SATCOM). The ICE3006 incorporates extensive Built-in-Test capability and is qualified for airborne applications. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3006. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
Product
Systems for Water Leak Detection
-
Here you are getting an overview about our devices for water leak detection. In our portfolio you can find systems for electro-acoustic water leak detection, compact onehand receiver, correlators, stationary noise loggers and a lot more...
-
Product
Tx/Rx BenchBlade
-
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for logic card characterization.The card includes a HM-ZD male right angle connector segment for access to the Zone 2 connectors of a switch fabric or node card. Edge-launch SMA connectors are utilized for ease of test cable attachment. SMT pads are included on the receive pairs.
-
Product
RFID
-
Leuze electronic GmbH + Co. KG
With RFID, no direct "visual contact" between the read-write unit and transponder is necessary. Information from the transponder is received by means of electromagnetic waves. As a result, these systems can be used practically and reliably under even the most adverse conditions.
-
Product
VTAC, Patchcord, ITA, 72", VTAC, Twinax, to Receiver, VTAC
7-141861142-072
-
VTAC, Patchcord, ITA, 72", VTAC, Twinax, to Receiver, VTAC.
-
Product
Rack Extender Kit, G12, 1.5" Deep
310113406
-
The Rack Mount Extender Block Kit is used for mounting to racks with recessed mounting rails recessed more than 1.” It is made of aluminum with a black anodized finish. NOTE: Used only with slide mounted G12 Receivers.
-
Product
Optoelectronics
-
Vishay is the world's number-one manufacturer of infrared components, with a portfolio that includes infrared receivers, emitters, IrDA transceivers, optocouplers, solid-state relays, and touch panels. Visible LEDs, optical sensors, photo detectors, plasma displays, and 7-segment displays complete Vishay's optoelectronics offerings.
-
Product
Conducted Emission
-
AFJ FFT 3010 & 3030 EMI Receivers have been especially designed for conducted emission measurement, both during EUT diagnostic development and for final compliance testing.
-
Product
Antenna, Octave Band Horn
EM-7020 | 1 GHz – 2.5 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Tool, Crimp, Micro Coax, Receiver and ITA
910101132
-
Tool Kit, Crimp, Micro Coax, f/ RG 316 and RG 179 wireIncludes p/n's 910101139, 910101135, 910101133.Used to crimp VPC micro coax contacts to RG316/179 wire. Includes receiver, ITA and crimp die.
-
Product
Gateway
CODA-4789
-
Hitron Americas Technologies Inc.
The CODA-4789 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~85/5~204MHz) offers the possibility of flexible integration to existing networks.
-
Product
Remote Dynamic Receiver
E1708A
-
The Keysight E1708A uses an optical fiber to transport the laser beam from a remote sensor assembly to the electronics. This improves measurement accuracy and repeatability by enabling you to mount heat-producing electronics away from the measurement area. The fiber optic cable also provides increased mounting design flexibility and easier access to the receiver attenuation and squelch adjustments.
-
Product
Cable Assembly, Receiver, 36", TriPaddle/Mini Power, 4 Banana Plugs, 7 Pin DIN
540198010211
-
Cable Assembly, Receiver, 36", TriPaddle/Mini Power, 4 Banana Plugs, 7 Pin DIN.
-
Product
DPSK Demodulator
-
Optical differential-phase shift keying (DPSK) provides a desired modulation format that offers high receiver sensitivity, high tolerance to major nonlinear effects in high-speed transmissions, and high tolerance to coherent crosstalk. In DPSK, data information is carried by the optical phase difference between adjacent bits. For direct detection of DPSK signal (by conventional intensity detectors), a DPSK demodulator is needed to convert the phase-coded signal into an intensity-coded signal.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 8 20-Pin Ribbon Cable Connectors
540160010140
-
Cable Assembly, Receiver, QuadraPaddle, 20", 8 20-Pin Ribbon Cable Connectors
-
Product
Antenna Impedance Converter
-
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
Product
Coax, Module, Receiver, 40 GHz, 90 Series, 8 Position
510104224
-
Primary mating module 510108169.
-
Product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
-
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)
-
Product
Track and Hold Data
-
Track and hold amplifiers are used to expand the bandwidth and/or high-frequency linearity of high-speed A/D conversion and signal acquisition systems. Track and Hold Amplifiers can be used in various applications including RF ATE Applications, Digital Sampling Oscilloscopes, RF Demodulation Systems, Digital Receiver Systems, High Speed Peak Detectors, Software Defined Radio, Radar, ECM & ELINT Systems and High Speed DAC De-Glitching.
-
Product
Frame Grabbers
Grablink Series
-
The Grablink frame grabber controls the camera scanning rate based on the signals received from a motion encoder. When the parts move faster, the acquisition line rate of the camera increases. When the parts move slower, the acquisition line rate of the camera decreases.
-
Product
Nemo Outdoor
NTA00002B
-
Nemo Outdoor is a laptop-based drive test tool for wireless network testing which supports over 300 terminals and scanning receivers from various vendors, all latest network technologies and latest smartphones. Nemo Outdoor offers a full drive test solution for wireless network testing / mobile network testing, troubleshooting, and optimization.
-
Product
Internal Antennas
-
Pulse offers a large selection of internal antennas that are designed into an incredibly diverse selection of solutions, from smart home IoT devices to utility meters, from point of sale products to wireless charging. The PCB antennas, including those made with flexible material, are made to be mounted or adhered against a plastic surface and connect via cable to your PCB, and cover the ISM, WiFi, GNSS, and cellular bands. The NFC selection for 13.56 MHz will work with both 50 and 80 Ohm radios and include antennas with a ferrite backing to work even when mounted against metal. The selection of active GNSS patch antennas with cable are perfect for ensuring your device’s whereabouts are accurately tracked. Finally, the many transmit and receive coils for wireless power charging will add this popular consumer capability to your product, cutting one final cable from design. Use the product finder below to find the perfect internal antenna solution for you.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH with M3 Jackscrews
540105020105
-
Cable Assembly, Receiver, TriPaddle, 20", 200-Pin Male LFH with M3 Jackscrews
-
Product
Integrated Tester for Aircraft Survivability Systems
ITASS
-
The Integrated Tester for Aircraft Survivability Systems (ITASS) verifies radar warning receivers (RWRs), missile warning systems, laser warning systems and other radio frequency (RF) systems onboard aircraft, providing operators the tools they need to confidently validate the operational status of the systems.
-
Product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
-
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
Product
Receiver, S6, 6 Module With 15" Platform For Tabletop
310122110
-
Receiver, S6, 6 Module with 15" Platform for Tabletop
-
Product
Compact Receiver Module
MixAMC-I
-
Virginia Diodes'' standard Spectrum Analyzer Extension Modules (SAXs) provide high performance broadband down-conversion and frequency extension of microwave specturm analyzers into the THz range. VDI now offers integrated MixAMC modules that provide industry leading performance in a compact package. These integrated MixAMC modules are used to down-convert millimeter-wave / THz signals only. Spectrum Analyzer Extension mode is not currently available for the MixAMC-I products. Integrated MixAMC modules utilize a low frequency LO input (<20 GHz) and have a seprate IF output port. Integrated MixAMC modules configured for high IF bandwidth may be available upon request.
-
Product
MIPI M-PHY v5.0 Receiver Conformance Test Software
N5991MM5A
-
The Rx solution including Station Configurator and Valiframe maximizes the usage of test instruments, providing automated system calibration as well as conformance testing according to the M-PHY 5.0 test specification (CTS).
-
Product
"Signal Transporter"
LTX-5525
-
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
Product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
-
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.
