Band-pass Filters
Refine signal, allowing transmission of only frequencies within a specified, continuous frequency band, while predictably attenuating frequencies above and below the continuous band.
-
Product
Broadcast Filters VHF TV
-
RFS bandpass filters are primarily used as part of multi-channel combiner facilities but can also be used to eliminate spurious emissions and increase isolation between co-sited services.
-
Product
2-Port Optical Tunable Filter
-
Optoplex's Tunable Optical Filter, also known as Optical Tunable Filter or Tunable Bandpass Filter, is an integrated module, consisting of micro optics and electronics. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). The selected channel can be varied (tuned) within the operating wavelength (frequency) range by a remote command sent through the built-in control PCB and firmware.
-
Product
Bandpass Filters
-
K&L Microwave provides bandpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
Product
High-Power Tunable Filter
CB503
-
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
Product
Bandpass Filter Components
-
Is a device that passes frequencies within a certain range and rejects (attenuates) frequencies outside that range.
-
Product
Passive Component Integration - MATRIQ
Passive Component Integration
The Passive is a highly customizable benchtop accessory that can integrate the passive components of your choice for convenient storage and integration into your test set up.We can customize the Passive module with a wide range of passive components: WDM couplers, splitters, circulators, band-pass filters, PM beamsplitters, MUX, DeMUX and more.Our spec sheet contains a selection of popular configurations.Please contact us to discuss your specific requirements at sales@quantifiphotonics.com.
-
Product
Wavelength Meter
S-107
-
Wavelength meter slot module of FOTS system offers two main functions of an accurate wavelength meter and a precise tunable band-pass filter. This accurate instrument, which is based on an internal tunable filter, acts as an optical spectrum analyzer or a wavelength meter as well as a low insertion loss tunable filter. The built-in tunable filter of the module is precisely tuned in C-band and L-band optical communication window by using both electronic and optical controlling methods. User can choose the function of this module depending on his or her applications.
-
Product
OEM Raman Miniature Probes
-
- Minimum Range: 210cm-1, up to 4000 cm-1 however limited by spectrometer range- Optical design: Bandpass and longpass filters in proprietary layout- Fiber coupling: FC connectors- Fibers: Typically 100µm single fiber for Laser Excitation, TBD for Signal Collection- Spot Size: 100-125µm on sample (**Other spot sizes on request)- Working Distance: 9 to 10mm- Dimensions: 106 x 21 x 33mm / 4.2 x 0.9 x 1.3mm
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
SWITCHABLE FILTER BANKS
FLT-1 WB
-
Matrix Test Equipment Incorporated
The Model FLT-1-WB is our Wide Bandpass filters for measuringthe Video Carrier and the Composite Second Order Beatdistortion on both sides of the carrier.
-
Product
Tunable Edge Filters
-
Tunable edge filter is a customized product. It usually belongs to 2-port optical tunable filter product platform. Instead of using narrow bandpass filter in the 2-port tunable optical filter, the tunable edge filter utilizes a low-pass or long-pass interference filter. By changing the incident angle of the light beam, the cut-off wavelength will be tuned. Standard Tunable edge filters support C-band or L-band wavelength range.
-
Product
Tunable Filters
-
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422 or BCD.
-
Product
Tunable Filters - Digitally Controlled
-
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning the desired signals while rejecting the interfering signals. The method of tuning can be either mechanical via a tuning knob mounted on the front of the filter, or electro-mechanical via an optional remote digital interface such as GPIB, RS-232, RS-422, BCD, ARC171, ARC234, Ethernet, USB or "Thumbwheel" panel mount.
-
Product
Lowpass / Bandpass / Highpass Filter
-
Corech Microwav’s RF Filers frequency ranges from dc to 67 GHz, band pass/high pass/low pass designs, narrow-band/wide-band types to meet customers various needs. These low pass filters(LPF), high pass filters (HPF), and band pass filters (BPF) offer very low insertion loss, outstanding VSWR and long-term performance.
-
Product
Filters
-
In order to minimize filter roll-off, we start with a quality, highly polished substrate and apply layers of metallization within tight tolerances. Our highly anisotropic ion beam etching process enables us to produce features down to 10 microns. Furthermore, the milling process yields a high consistency from circuit to circuit meaning that whether we produce 1 or 100,000 filters, each one will have consistent filter roll-off characteristics.
-
Product
Highpass Filters
-
Frequency range of this band pass filter is 1,000 MHz to 2.5 GHz and the passband is 1.5 GHz. PE8715 highpass filter is one of over 40,000 RF microwave and millimeter wave components supplied by Pasternack. Our 5 section highpass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
Product
Lowpass Filters
-
Frequency range of this lowpass filter is DC to 100 MHz and the passband is 100 MHz. PE8719 lowpass filter is one of over 40,000 RF, microwave and millimeter wave components supplied by Pasternack. Our 5 section low pass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
Product
dv/dt Filters
-
dV/dT Output Filter Modules effectively protect motors against these high voltage spikes due to the use of motor cables between IGBT based motor drives and motors.
-
Product
High-Power Filters
-
Beehive Electronics designs custom high power RF filters used in vacuum coating systems. Our experience spans from kilohertz to gigahertz and power levels up to 50 kilowatts. We provide a turnkey solution: we design, build, and test the filters to the customer's specification.
-
Product
Filters
-
Filters are components with a function that only extracts the required electrical signals, and removes the unnecessary electrical signals in electrical circuits. Murata offers a lineup of filters for various devices and functions.
-
Product
Automated Filter Tester
8130A
-
The Automated Filter Tester Model 8130A continues to be the best solution for testing particulate respirator filters, disposable filtering face pieces, and a wide assortment of filter media. The TSI filter testers have been used in quality control and manufacturing by leading filter and filter media manufacturers and test centers around the world for more than 20 years.
-
Product
Notch Filters
-
K&L Microwave provides notch filters, also called bandstop or bandreject filters, in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design. When considering a particular family of parts, use Filter Wizard (a link button will be provided when appropriate) to determine a specific part number within the given family.
-
Product
EMC & EMI Filters
-
CTS is the leader in EMI/RFI filters and offers a diverse product line of standard as well as custom filters to suppress electromagnetic interference (EMI) / radio frequency interference (RFI), thereby providing customers with a wide range of electro-magnetic compatibility (EMC) solutions. Discover cutting-edge solutions for your electromagnetic compatibility needs with CTS EMC products. Our innovative range is engineered to deliver unparalleled performance, ensuring seamless connectivity and optimal functionality across diverse industries.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Notch Filters
Power-Pole Notch Series
-
POWER-POLE® Notch Filters offer improved performance and power handling over our MINI and MAXI Notch Filters.
-
Product
Filter Design Software
QuickFil
-
QuickFil is a software for designing passive electronic filters. The result is an optimized circuit of inductors (L)and capacitors
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Highpass Filters
-
K&L Microwave provides highpass filters in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design.
-
Product
SIM Filter
-
The CFL SIMF, Cable Fault Secondary Impulse Filter from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately.
-
Product
EMI Filters & Adapters
Emissions
-
The commonality in this section is conducted noise. Noise is not just a consideration when complying with EMC legal requirements, its is also potentially damaging and/or cause of failure of product performance or communications, even if the noise level is below EMC standards limits.
