Wide Band
A "wide" frequency range with channels substantially wider than the coherence bandwidth.
-
Product
Wide band Directional Power Meter
RF ONE 3029
-
The RF One Power Meter is a very versatile instrument covering both analog and digital carriers in an extremely wide frequency range from 30MHz to 6GHz.
-
Product
Wide Band Filters (multi-octave)
ERF-5W™ Series (Single & Dual)
-
The new ERF-5W™ filter takes Pole/Zero’s MINI-ERF® technology to a higher level of RF power handling, with 5W (average) in-band power handling, and covering the entire military tactical radio tuning range of 30-520 MHz in one integrated package. This tunability is accomplished by the use of three poles of selectivity, multiple internal tunable filters along with high performance PIN diode RF band select switches. The tunable filters are designed to minimize size and power consumption, while maintaining high RF power handling and linearity characteristics. Serial control is accomplished via a standard Serial Peripheral Interface (SPI)-based bus.
-
Product
Wide Band Filters (multi-octave)
MINI-ERF® Series
-
The MINI-POLE® Extended Range Series of tunable filters was developed to address applications needing a small, surface mount package with wide tunability. This tunability is accomplished by the use of multiple internal tunable filters along with high performance PIN diode RF band select switches all contained in one housing. The tunable filters are designed to minimize size and power consumption while maintaining high RF power handling and linearity characteristics. Parallel or serial digital interface can be selected by a mode pin for ease of integration into your design.
-
Product
Wide Band Filters (multi-octave)
GEN3-ERF®
-
The 3rd Generation Mini-ERF is a Reduced SWaP-C, 30 to 520 MHz tunable bandpass filter that features 50mW (typ.) power consumption, 1 Watt CW continuous power handling (7% BW), +40 dBm IIp3 (typ.), low insertion loss, and 4 dB typ. selectivity @ +/-10%, (7% filter). The GEN3-ERF’s are fully tuned and tested by Pole/Zero® for convenience and ease of use.
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
Saluki S3871X Series Solid State Power Amplifier (max. 500W output power)
-
S3871X series is a broadband benchtop solid state power amplifier and incorporates the patended spatial power combination technology. It is designed to have features of broad bandwidth, high gain, high power, wide dynamic range, low spurious signals and extremely load tolerant. These features enable the amplifier to be used as a cable test instrument covering multiple frequency bands.*Wide frequency range, 9kHz to 110GHz, max. 500W output power*
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Signal Amplifier
9400
Amplifier
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Coaxial Power Detector
-
RF Lambda’s coaxial power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Programmable Step Attenuator DC~50GHz, 0~115dB Att.
-
The programmable step attenuator achieves step attenuation over a wide frequency band. It features high attenuation accuracy, excellent repeatability, low insertion loss, and long service life. Its primary applications include controlling the amplitude of signals entering systems, regulating output signal power in systems, and adjusting impedance matching between signal sources and loads. It is widely used in various broadband spectrum analyzers, broadband vector network analyzers, broadband synthesized signal sources, noise figure test sets, and diverse microwave automatic test systems.
-
Product
Wide Band Filters (multi-octave)
NANO-ERF® Series
-
The NANO-POLE® Extended Range Series of tunable filters was developed to address applications needing an extremely small surface-mount package with low power consumption. Wide tuning range is accomplished with careful design to minimize size and power consumption.
-
Product
Narrow Band LNA Family
-
The COMM-connect range of Narrow Band Low Noise Amplifiers can be used to amplify signals in a very wide range of bands. The amplifiers comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
200GHz DWDM Module(4,8,16 Channel)
-
Flyin Optronics’ 200GHz dense wavelength division multiplexer (DWDM) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
Product
Broad Band Amplifiers
-
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
Product
Broadband Amplifier
BBA300
Amplifier
The R&S®BBA300 broadband amplifiers are a new generation of highly compact solid-state broadband amplifiers designed for high availability. They feature extremely wide, continuous frequency bands extending up into the high microwave range, along with high linearity, outstanding noise power density and excellent harmonic characteristics. They also boast high system configuration and operational settings flexibility.
-
Product
Unequal Split Power Tappers
-
Pasternack unequal split power tapper product designs are also known as unequal couplers, power dividers or splitters, cross band couplers and signal samplers. Many of our unequal couplers / tapper series are RoHS and REACH compliant. Unequal RF tappers from Pasternack are available with 4.1/9.5, 4.3-10, 7/16 DIN and Type N connector options. These unequal split power tapper components for RF are manufactured to precise specifications required for accurate specified values listed for each product. Unequal split tapper products work with high power of up to 300 watts depending on style. Frequency ratings for unequal power splitter line are wide band components with a 380 MHz to 6 GHz frequency range, based on model selected. Pasternack RF power tappers in unequal design can be ordered with various directivity (dB) values of 4.8dB, 5dB, 6dB, 7dB, 8dB, 9dB, 10dB, 11dB, 12dB, 13dB, 15dB, 16dB, 20dB, 30dB depending on model. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this unequal split power tapper/coupler/divider series for RF is in-stock. These unequal split power tappers are not just in stock, but they will also ship the same-day are they are purchased.
-
Product
KW Phase Array Radar Jamming System C, X, Ku, K, Ka And V Band
-
Digital Step Phase Shifter. Digital Step Attenuator. RF Solid State High Power Switch. Front End Low Noise . mplifier for Feedback. Transmit Solid State Power Amplifier Matrix 4x4, 8x8 or 16x16. Ultra Wide Band Flat Panel Antenna. Rotary Joint 360 rotation capability.
-
Product
Signal Amplifier
9200A
Amplifier
Model 9200A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
100GHz DWDM Module(4,8,16 Channel)
-
Flyin Optronics’ 100GHz dense wavelength division multiplexer (DWDM) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
Product
100GHz/200GHz DWDM Module in LGX Box
-
Flyin Optronics’ 100GHz/200 GHz dense wavelength division multiplexer (DWDM module) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
Product
Band Pass Filters
-
*High power handling 200W with a wide range of bands available*Excellent Isolation with Low Intermodulation*High reliability of >500K Hours MTBF and multi-strike lightning protection*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Partial Discharge Measuring Equipment
-
Different from a conventional partial dischargemeasuring set provided with a fixed testingfrequency, Model DAC-PD-5 is newly designed toselect the center and the bandwidth of testingfrequencies so that partial discharges emitting in anoptional frequency in the range of a specifiedbandwidth can be detected. Generally, partialdischarges are measured in a wide band frequencythough; the detecting sensitivity must be lowered inorder to detect partial discharges partially.DAC-PD-5 has a wider bandwidth and can measurepartial discharges in a high sensitivity by bypassingnoises emitting bands.
-
Product
0.5-18GHz High Performance Receiver
QR026
-
The Teledyne Defence & Space (TDS) Single Channel High Performance Receiver provides a new approach for ESM / ELINT applications, incorporating patented features offering wide band synthesized capability from 500MHz to 18GHz, with frequency extensions available up to 40GHz.TDS’s new QR037 digital receiver module combines high dynamic range RF down conversion and LO generation with digitisation and signal processing capabilities to provide a compact solution for a number of ELINT/COMINT and ESM applications.Excellent dynamic range and linearity is achieved through a combination of RF and digital down conversion stages coupled with high performance pre-selection and IF filtering.
-
Product
Accelerometers
-
Columbia Research Laboratories
The force balance accelerometer has a classical critically-damped, second-order frequency response. There is no peaking in the response but simply a smooth roll-off above the natural frequency. This property along with the excellent characteristics of the "HP" torquer design makes Columbia accelerometers the best choice for demanding applications where precise DC and near-DC measurements are needed in demanding shock and wide band vibration environments. Columbia force balance accelerometers are available to cover virtually all applications. Low noise, high output units can be used for seismic structure motion studies while miniature, high range versions are optimum for measuring more violent high G environments encountered in many industrial, aircraft and missile applications.
-
Product
CWDM Mux/Demux in 1U Rackmount(4,8,16,18-Channel)
-
Flyin Optronics’ Coarse wavelength division multiplexer (CWDM Mux/Demux) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging. It provides low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path.
-
Product
Digital AC milli Volt meter
-
PGP Electronics Private Limited
PGP Electronics Digital AC Mill voltmeter is a very versatile and general purpose equipment for the measurement of audio frequencies. It is useful in measuring low amplitude signals over a wide band of frequencies with precision. Its has a wide band width and sensitivity is 10uV. This instrument is useful for all amplifiers/ audio system manufacturers, college laboratories to measure input/output of any amplifier as well as frequency response of that amplifiers. .
-
Product
High Precision LCR Meter
MCR-5000 series
-
MCR5000 series is a multifunctional LCR precision meter used for testing various electronic components. Adopt 4.3-inch TFT LCD display, simple display, elegant layout. It is a high speed, wide band, 5 bit test resolution impedance measuring instrument with 40hz-200khz multipie frequency points and 0.1% accuracy, which can meet the requirements of component parameter detection in various occasions. Is a high - quality cost-effective tester.
-
Product
2-Channel DAC FMC Module
FMC230 – HPC
-
Sundance Multiprocessor Technology Ltd.
The FMC230 is a dual channel DAC FMC with a very wide band. The two 14-bit D/A channels operate at 5.7Gsps (2.85Gsps direct RF synthesis) and are clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC230 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
ESU Analyzer
ESU-2050
-
The BC Biomedical ESU-2050 ESU Analyzer is the first instrument of its kind on the market. Designed through extensive collaboration with several of the world's leading electrosurgery generator manufacturers. It is the only ESU Analyzer on today's market with a 1% reading level of accuracy. Calibration quality analyzer; uses external precision non-inductive test loads and wide band current transformer.
-
Product
100G,200G 1X2 DWDM Device (3Ports)
-
Flyin optronics’ 100GHz/200GHz 1x2 wavelength multiplexer utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
