Force
exerts an influence.
See Also: Compression, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Electrodynamic Shaker Systems
-
Electrodynamic shaker systems and amplifiers from MB Dynamics help to support a wide range of general-purpose vibration test requirements. The electrodynamic shaker systems are offered in a variety of force ranges, from 100N (25 lbf) to 22kN (5,000 lbf). The innovative design of MB Dynamics PM-Series electrodynamic shakers incorporates permanent magnet technology and the voice coil principle to create vibration. These heavy-duty electrodynamic shakers feature a robust design for maximum reliability, with end-users reporting a useful service life of 10, 25 or even 40 years! The shakers come in five unique sizes, with peak sine force ratings of 100 N, 200 N, 500 N, 1000 N and 2000 N; or, 25 lbf, 50 lbf, 100 lbf, 250 lbf and 500 lbf. The MB Dynamics C40HP electrodynamic shaker outputs 22 kN or 5,000 lbf peak. The C40HP is a part of the legacy C-Series of shakers, which have served as the foundation for today’s modern electrodynamic vibration test equipment industry.
-
Product
Performance Exams
-
Sturdy sheet steel housing with safety door and electrically driven base with built-on sample mold. The compaction takes place via a rolling segment with force / path-controlled drive device from above. The sample mold and the rolling segment are equipped with software controlled heating. The measurement of force and displacement is done by electronic sensors. The entire compaction process is controlled with Windows software and PC via preselected sequence programs.
-
Product
Power Circulation Type Flat Road Tire Comprehensive Performance Tester
-
This system has a performance performance system that simulates the force applied from the vehicle side to the tire and the influence exercised from the road side by a high speed transfer unit and a high response torque generator with a power circulation system.
-
Product
DDR4 X16 2-wing BGA Interposer For Logic Analyzers, Connects To 61-pin ZIF
W4641A
-
The W4641A DDR4 2-wing BGA interposer for DDR4 x16 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A the W4641A is the smallest BGA interposers for DDR4 x16 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
Grippers
-
Omega carries a wide variety of pneumatic grippers with a wide range of gripping forces and stroke lengths. We carry mineature or robust models or for clean or harsh environments.
-
Product
Incline Impact Tester
-
Evaluates the ability of the packaging system to withstand sudden horizontal impacts or crushing forces.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1L24-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Accordion Custom Connectors
-
ECT’s Accordion Custom Connectors offer high reliability, high cycle life, patented single beam architecture providing a large range of usable compliance to absorb connector to target mating tolerances. With no requirement for a male to female target penetration, superior ease of use is achieved in blind mate scenarios with low insertion/extraction forces.
-
Product
1 N Clip Grips
-
These very low force 1 N (0.22 lbf) clip grips are for tensile testing fibers, tapes, and other similar shaped specimens. They are designed for use with 50 N (11 lbf) and below load cells.
-
Product
Load Cells
-
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Product
Ultra High 2.84 (81.00) - 10.00 (283.00) High Performance Lead Free Probe
LFRE-1A-10
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Hand Dynamometer Logger Sensor
NUL-237
-
This sensor comes with a hand held unit with a built in strain gauge. The sensor measures the pressing force on the hand held unit.
-
Product
3-Component Quartz Force Rings
260 Series
-
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
Product
Static Constant Loading Tester
-
Static Constant Loading Tester is mainly used to determine the resistance to the axial static constant load of plastic manhole. A constant force is steadily loaded on the axial direction of the manhole for the specified time, when the test is finished, observing the sample appearance (deformation, collapse, crack or crazing), determine the deformation in axial direction and calculate the deformation ratio of manhole. The machine is also suitable for ring stiffness test, flattening test, ring softness test of thermoplastic pipes.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
Tablet Hardness Testers
-
Teledyne LABS offers both manual and automated tablet hardness testers. Tablet hardness testing is a method of determining mechanical properties of a drug product, typically oral dosage forms such as a solid dose tablet. Tablet breaking force (commonly called tablet hardness) is a crucial characteristic in the manufacture of solid dose formulations. Tablet hardness testing is a major step in tablet consistency and quality control.
-
Product
Acceleration Testing
-
The acceleration test is performed on a centrifuge to assure that material can structurally withstand the steady state inertia loads that are induced by platform acceleration, deceleration, and maneuver in the service environment, and can function without degradation during and following exposure to these forces. Acceleration tests are also used to assure that material does not become hazardous after exposure to crash loads. The acceleration test method is applicable to material that is installed in mobile platforms such as aircraft, helicopters, aerospace vehicles, air-carried stores, ground-launched missiles, trains, ships, automotive vehicles, etc.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe
LFRE-1I-4
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Decelerometer
-
Maschinenbau Haldenwang GmbH & Co. KG.
National type approval by the PTBPrinter with keyboard and digital displayFast matrix printer with graphic expressionPiezoelectric decelerometersControl and measurement electronicsElectrical equipment adjustment by means of digital displayGyro sensor for automatic compensation of the measurement error by the pitch behavior of the vehicleJacks for pedal force, pressure u. Load indicatorRS-232 interface to PC with data transfer for standard table SoftwareChargerSpare roll of paper approximately 15 mplastic suitcase
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Hydraulic UTM
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Uses hydraulic systems for force application.
-
Product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1V-2
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Digital Weighing Indicator | Process Meter | Panel Meter
-
Mantracourt’s digital weighing indicator and panel meter modules are compatible with a wide range of sensors and transducers, including volts, amps, temperature, frequency, speed, load, force, pressure, torque, LVDT, RVDT and many more. The digital architecture offers simple one-pass calibration and fast setup.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
Converter Of Electrical Quantities
-
The converters are intended for the conversion of electrical quantities DC signal which is either in form of the DC voltage, or the DC forced current. They can be used in connection with indicating pointer instruments, calibrated in units of the measured quantity, or with a recorder or, eventually with a digital instrument.
-
Product
Impact Hammer
WaveHitMAX
-
The invention of the first smart impact hammer provides new ways of mechanical excitation for structural dynamic applications. Smart means that the device processes its signals internally. The modal hammer WaveHitMAX guarantees fully automatic, reproducible and high-precision excitation of the test object without double hits. The user can set the number of hits, impact force and the delay between hits accounting for different degrees of damping / delay times. All presettings like zero point or impact force search are made automatically by the hammer. Manual adjustment by the user is no longer necessary.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
