Fiber End Face
-
Product
Fiber Identifier
-
Fiber identifier is an essential installation and maintenance instrument which can identify the optical fiber by detecting the optical signals transmitted through them,during this process the fiber optic identifier generate no harm or damage to the fiber cable and it do not need opening the fiber at the splice point for identification or interrupting the service.This fiber identifier detects frequency tones at 270Hz, 1KHZ, 2KHZ, when traffic is present on the fiber under test, an audible tone can be heard. In the meantime, it can identify the traffic direction that indicated by LED with illumination.
-
Product
Signal, Patchcord, Receiver, 72", TriPaddle, 22 AWG, Single Ended ( 5 Amps)
7-104922000-072
-
Signal, Patchcord, Receiver, 72", TriPaddle, 22 AWG, Single Ended ( 5 Amps).
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Tinned Ends, Spring Latches, 1m
A096SFR-T-5B100
-
The 96-Pin 1.27mm pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
Front End Protector
AS-RXFEP RX
-
The AS-RXFEP Receiver protector limits input RF signal threshold from 1 to 150MHz to less than 0.3 Vrms to protect a receiver front end from damage due to nearby transmitted signals. The receiver still actsnormally and measured signal strength is not affected.The circuit uses a multi-stage design of transformer saturation coupling and current limiters. It also incorporates a low voltage GDT to protect from lightning events. These are for receiving only - you cannot transmit through them without damaging the unit.
-
Product
Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 3' Wires
GX96405
-
Mating coax connector and 20 coax pins crimped (both ends) to 3 ft wires
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 0.5m, 90º
A1604FT-T-0A050
-
For applications where a 90 degree down cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, MU Connectors, With Interlock
42-850A-314-M62.5-HI
-
The 40/42-850A-314-M62.5-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
A Ready-to-use Solution To Orientate Polarization Maintaining Fibers Inside Connectors
PM ALIGNER-V2
-
PM Aligner-V2 is the simplest way to orientate precisely a PANDA Polarization Maintaining fiber inside a connector or ferrule. With a long working distance, PM Aligner-V2 allows the operator to work manually around the ferrule of the connector. After positionning, the curing phase becomes easy to realize without affecting on the PM fiber alignement.
-
Product
Automatic Fiber Jacket Stripping Machine - FBT-3000
-
Shanghai Fibretool Technology Co.,Ltd.
The FBT-3000 automatic fiber peeling machine is a new type of optical cable end processing equipment, which is based on the eagerness of optical fiber connector manufacturers to improve production efficiency and reduce the skilled manual emergence of optical cable end processing equipment. In order to solve the problem that the skin layer of optical fiber is usually peeled manually with wire peeling pliers, and the artificial denudation is low in precision, low in working efficiency and low in product quality.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Cut Ends, 2m
40-972-403-2m-MU
-
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 0.5m
A1604FR-T-0A050
-
A range of DIN41612 cable assemblies with unterminated connections on one end. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Single Mode Fiber Optic Rotary Joints
-
Single Mode Fiber Optic Rotary Joints (FORJ) can be supplied as a stand alone product. Its features can be customized : wavelength, connectors, characteristics of the fiber…
-
Product
4 Ports 1GbE Copper (RJ-45) Ports + 4 1GbE Fiber (SFP) Module
NMC-0805
-
Ideal for network segmentation applications and fiber-based networking. 2 x Intel® i350-AM4, 4 x 1GbE copper RJ-45 + 4 x SFP slots, 2 x PCIe x4, Gen2, RoHS compliant.
-
Product
Mating Coax Connector With 20 Coax Pins Crimped (One End) To 5 Foot Wires
GX96404-60
-
Mating Coax Connector with 20 Coax Pins crimped (one end) to 5' wires. Coaxial cable: RG316, 50 ohms.
-
Product
Cable Assembly, 25-Pin D-Type, Female To Unterminated With Tinned Ends, 1m
A026HF4-T-0A100
-
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks.
-
Product
CATV / RF Over Fiber
-
Transport RF signals: Cable TV (CATV), L-Band (SMATV), NTSC, DOCSIS, Return Path and other RF signals over 110km over a single fiber.
-
Product
Fiber Acceptance Test Kit
23005
-
The unique design of the splice accommodates either 125um or 140um fiber and any size buffer up to 900um. The precision made splice holder firmly holds the pigtail in position without causing stress on the fiber. The low viscosity index matching liquid has an indefinite shelf life and allows for an easy glide of the bare fiber into the splice. Within seconds, a fiber acceptance reading can be made with an OTDR or test set. Low loss with minimum back reflection can easily be achieved for more accurate signatures. Other applications for this kit: splice training aids, bare fiber adapters, and temporary splicing.
-
Product
Mini Fiber Tester (SC Type)
21-8682-00
-
The portable design is easy to carry and operation. 2. Low-cost multi-function is more economical. 3. The multiple LEDs display a clear indication. 4. Power saving automatically and Battery low indication.
-
Product
Cable Assembly, 32 Pin .100 (2.54mm) Pitch Ribbon Cable, 36" Double Ended
515109163
-
Cable Assembly, 32 Pin .100 (2.54mm) Pitch Ribbon Cable, 36" Double Ended
-
Product
Integrated Solution for Digital Switching & Fiber Optics Operational Verification
VERTA
-
When incorporated into defense/aerospace ATE, Verta enables reliable, error-free bus communication and interoperability tests to verify performance of high-speed, optically networked military weapon assemblies.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors, With Interlock
42-850A-514-M62.5-HI
-
The 40/42-850A-514-M62.5-HI is a PXI/PXIe 4-channel multiplexer with ST connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
RGB Digital Fiber Optic Amplifier
CZ Series
-
RGB Digital Fiber Optic Type. RGB three-light source. Wide detection range of up to 7020 mm. High-speed response of 300 s. Water-resistant sensor head IP-67 rated
-
Product
End-to-End Software Testing Services
-
A lack of tools, training, time, and other resources is a major obstacle for dev teams, preventing them from sufficiently testing before release. We identify your key risk areas with a maturity assessment and help build the right test plan for you, working towards a culture of continuous feedback. Learn more about our software testing solutions below!
-
Product
Multi-Wire Fiber Jacket Stripper - TFS-304-16
-
Shanghai Fibretool Technology Co.,Ltd.
1. This stripper is suitable for stripping duplex and multi-core Fiber Cables: 4 cores ×2.0mm DUPLEX cables, 2 cores ×3.0mm DUPLEX cables and 2 cores × MTP/MPO multi-core optical cables.2. 2~4 core cable can be stripped by one operation3. Cable stripping length is adjustable from 5 mm-42 mm4. All cutting surface are precision formed, hardened, tempered and anti-rust 5. The comfort anti-fatigue design handle ensures long-term workmanship 6. Length: 161 mm, weight: 145.50g
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m, HV
A009DM5-T-HA050
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Tinned Ends, 2m, 45º
A1604F5-T-0A200
-
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 1m, Spring Latch
40-972A-068-1m-FU
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
6GE+2G Single-Mode Fiber Port Unmanaged Ethernet Switch, -40~75℃
EKI-2728SI
-
Provides 6 x 10/100/1000 Mbps Ethernet port with RJ45 connector, Provides 2 x 1000 Mbps fiber port with SC type connector for 1000Base-SX/LX device. Supports MDI/MDI-X auto crossover, Supports Auto-Negotiation, Supports redundant 12 ~ 48 VDC and 24VAC power input.
-
Product
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-103922000-072
-
Signal, Patchcord, ITA, 72", TriPaddle, 22 AWG White, Single Ended ( 5 Amps)
-
Product
AutoGet auto Focus Portable Fiber Endface Inspector
CA3008
-
CA3008 Autoget is an intelligent portable fiber enface inspector. with newest hardware and software, and with functions of auto focus, auto exposure,auto analysis, autogenerate report, auto image transmission, etc. Autoget can clearly find out the defects of fiber endface, such dirts, scratches.
