Electrical Fast Transient
-
Product
Semiconductor Electrical Test
-
We conduct electric property test (final test) of the completed (packaged) LSI products. We will support testing of analog devices, logic devices, other electronic parts, modules, application products and so on. We will test according to customer's specification regardless of evaluation, trial production, mass production, by know-how cultivated with long-time mass production results. Test initial examination ~ From consistent correspondence up to selection and evaluation, individual correspondence such as design only is accepted.
-
Product
Non-Multiplexed High Speed Transient Function Card
-
Identified by its ADC per channel and on-board memory, it typically operates at per channel sampling rates which in aggregate would overwhelm any communication system. Data is stored on board during a test and transmitted to a host computer following completion.
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
Product
Photovoltaic and Electrical Installation Testers
3108
-
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
Product
100MHz, 2 Channel PXI Oscilloscope, Spectrum Analyzer, Transient Recorder & Voltmeter
TE6100
-
The TE6100 is the first 100 MS/SEC measuring instrument that consists of a Digital Storage Oscilloscope, Spectrum Analyzer, Transient recorder and Voltmeter. This new PXI based, compact measuring instrument, can solve almost every measurement problem. Analyzing signals is done with an 8-bit resolution and a maximum sampling speed of 100 MHz. The input ranges 0.1 Volt full scale to 80 Volt full scale. The record length is 32K/64K samples.
-
Product
Development Test for Electric Motors with Power Electronics
-
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
Product
Electric Vehicle Supply Equipment ATS (EVSE ATS)
-
It is a customized system based on Chroma 8000 ATS specializing inverification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.
-
Product
Electric Multipliers
EFC
-
The easy-to-operate EFCip electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines and rigs, the Mountz torque multipliers achieve precision torque in a quick, cost-efficient manner.
-
Product
4 Channel Variable Gain Fast Amplifier
V974
-
The Mod. V974 is a 4 channel fast rise time amplifier housed in a 1-unit VME module; each channel features a voltage gain adjustable from 1 to 10 in x1 steps. Channels are non-inverting and bipolar: they amplify both positive and negative signals.
-
Product
Electrical Safety Analyzer
19032
-
Chroma Systems Solutions, Inc.
Our Electrical Safety Analyzers combine Hipot, Insulation Resistance ( IR), Ground Bond (GB), Leakage Current (LC)/AC LC/DC LC, and Dynamic Function Tests. Savings can be up to 50% of production line space by not having to purchase and rack several safety test instruments. It also increases efficiencies of electrical safety testing and reduces associated labor costs.
-
Product
Battery Electrical System Analyser
-
We invented the “Resistance method” which uses a series of shorting pulse to measure the voltage drop in order to calculate the plate’s internal resistance. Unlike other patented “Conductance method” which generates an AC pulse across the battery terminal to measure impedance.
-
Product
Electric Servomotor Threaded Impact Tester
-
This equipment is a new type of impact test equipment that uses the uniquely developed servomotor with ultra-low inertia and high torque that is used in our vibration.
-
Product
Transient Voltage Suppressors (TVS)
-
A transient voltage suppressor (TVS) is an avalanche diode specially designed to clamp overvoltages and dissipate high transient power surges. ST’s Transil™ protection devices are able to shunt a high current surge for a short duration.
-
Product
Electrical Probe Systems
-
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
Product
Electric Linear Actuators
MaxJac
-
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
Product
RV Protocol Trailer Light and Electric Brake System Tester
RVCHECK
-
The RVCHECK is a fast, easy, low-cost way to test RV lighting and electric braking systems. In addition to powering an RV trailer's lighting circuits for easy checking, your RVCHECK measures the current draw of the electric brake coils, and checks the break-away battery circuit.
-
Product
PC Based Test Setup for Electric Iron Testing
-
SCR ELEKTRONIKS make PC Based Test Setup for Electric Iron Testing is useful to carry out various tests mentioned in IS 366:1991 clauses 10,11,12,13 & 14 on the Iron under test.
-
Product
100MHz, 2 Channel ISA Oscilloscope, Spectrum Analyzer, Transient Recorder, Voltmeter & Abitrary/Function Generator
TP801-AWG-ISA
-
The TP801 AWG is the first ISA card based 100 MS/second measuring instrument that consists of a Voltmeter, Oscilloscope, Spectrum analyzer, Transient Recorder and an AWG (Arbitrary Waveform Generator).
-
Product
Dynamics & Transients Analysis Software
-
Dynamics & Transient analysis software enables engineers to simulate sequence of events including power system disturbances and evaluate system stability by utilizing an accurate power system dynamic model.
-
Product
HandyScope HS5: 500 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 40MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-540XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 500 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Electrical Testing
-
Board defects are never an option. Your customer expects perfect boards, each time, every time. Electrical testing is the key in ensuring that the connectivity of a PCB is precisely as specified and that there are no defects or flaws that may cause problems down the line.
-
Product
75/85/100 GHz, 1/2/4 Port, Electrical Remote Sampling Head Module
N1046A
-
75 GHz, 85 GHz or > 100 GHz maximum available bandwidth (selectable option, upgradable)1, 2 or 4 channels per module User-selectable bandwidth settings starting at 60 GHz Electrical inputs: 1 mm female
-
Product
Multifunction Electrical Installations Meter
MPI-520
-
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
Product
Static Electricity Measurement Management Set
NK-1B / NK-2B
-
We have all the measuring instruments for solving ESD troubles.It is easy to carry and is ideal for process diagnosis.You can send it as it is by courier.Ideal for in-house static electricity education.A special soft case is attached so that the measuring instruments can be carried individually.
-
Product
Electric Servo Motor Type 3-axis Vibration Tester
-
The Electric Servomotor Vibration Test System Is A New Vibration Test System Developed Based On The Control Technology Of AC Servomotors That We Have Cultivated Since Its Establishment.
-
Product
Brushless Electric Torque Screwdrivers
VB-Series
-
The HIOS VB-Series brushless electric screwdriver is designed to plug directly into a power outlet and does not require a separate power supply unit. Features a high performance brushless motor design provides durability and reduces the standard maintenance costs for electric screwdrivers. Operates on a duty cycle of 0.5 seconds on and 3.5 seconds off.
-
Product
Airframe Electrical Power Systems
System
Rely on Astronics CorePower® airframe electrical power systems, where solid-state technologies deliver highly efficient, clean power that improves aircraft operation through weight and system wiring savings.
-
Product
Electric Power System Characteristics Test
-
This test is also known as the power supply line voltage and frequency variations test. A few of the measured characteristics are: voltage and frequency modulation, voltage spike, and voltage transient recovery.
-
Product
Electrical Creep and Rupture Testing Machine
ECR Series
-
Jinan Testing Equipment IE Corporation
This series of computer control electronic creep and rupture testing machine is newly designed with full-digital measuring control system to meet the standards of GB/T2039, GB//T20120, EN ISO 204-2009 and ASTM E139 etc. The electronic creep and rupture testing system can perform not simply creep. stress-rupture test and stress relaxation test on metals under room or high temperatures, but also low cycling test & creep fatigue test. The electronic creep and rupture testing machine is widely used for quality control in factories, material research in R&D department and teaching in universities,
-
Product
Portable Electricity Meter Testers
EE-120A-3S
-
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
