Surface Contamination
-
Product
0.25° Accuracy Roll & Pitch Surface Dynamic Motion Sensor
DMS-525RP
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
19" Drawer with Writing Surface, Unshielded, 10.5"H x 30"D
DR-101930-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Air and Water Permeabilityin Concrete Both At and Below the Surface
Poroscope
-
Poroscope Plus measures the time it takes for air to flow into a known volume of a sealed, evacuated chamber in the concrete. While the vacuum reduces from -55 Kpa to -50 Kpa, a measure of air permeability is determined. For water permeability, Poroscope Plus uses the same chamber filled with water, and measures the total time in seconds for a volume of 0.01 ml of water to escape.
-
Product
IEC60335 Clause 21.101 Copper Test Vessel For Hotplate Surface Test
CX-103
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335 clause 21.101 copper test vessel for hotplate surface test
-
Product
Surface Resistance Meter
SRMETER2
-
The Surface Resistance Meter is a wide range, multi-scale, auto-ranging meter. This meter is appropriate for auditing static control work surfaces.The meter is 9V battery powered and simple to use.NIST Calibrated
-
Product
EDX-FTIR Contaminant Finder/Material Inspector
EDXIR-Analysis Contaminant Finder/Material Inspector
-
EDXIR-Analysis software is specially designed to perform qualitative analysis using data acquired by an energy dispersive X-ray (EDX) fluorescence spectrometer and a Fourier transform infrared spectrophotometer (FTIR). This software is used to perform an integrated analysis of data from FTIR, which is excellent at the identification and qualification of organic compounds, and from EDX, which is excellent at the elementary analysis of metals, inorganic compounds and other content. It then pursues identification results and the degree of matching. it can also be used to perform EDX or FTIR data analysis on its own. The library used for data analysis (containing 485 data as standard) is original to Shimadzu, and was created through cooperation with water supply agencies and food manufacturers. Additional data can be registered to the library, as can image files and document files in PDF format. It is also effective for the linked storage of various types of data as electronic files.
-
Product
3D Micro Coordinate Measurement Machine and Surface Roughness Measurement Device
InfiniteFocusSL
-
With the InfiniteFocusSL you are able to measure form and roughness of your components with only one system. In addition, color images with high contrast and depth of focus are achieved. The robust frame and the intelligent illumination technology provide fast and high-resolution measurement in the laboratory and a production near environment. The measurement system is particularly attractive due to its cost effectiveness, measurement speed and usability. The long working distance in combination with the above average measurement field allows a wide range of applications. Measurements are achieved within seconds, and features, such as a coaxial laser for quick and easy focusing, enhance its usability.
-
Product
Photoemission And Surface Photovoltage Spectroscopy
-
KP Technology have developed a range of modules that feature surface photovoltage and photoemission spectroscopy capabilities.
-
Product
Rework Station, Dual, Surface Mount, 896 °F
21-10130
-
The 21-10130 is a SMD Rework Dual Station, intelligent rework station which combines rework station with soldering station to become an essential centerpiece of any technician or hobbyist bench. A MCU thermostat provides accurate and consistent working temperature. The dual LCD displays show live working states of both the iron and the hot air hand pieces, as well as provides access to three programmable presets for each unit. Temperature and airflow for the hot air tool can also be controlled from buttons on the hand-piece.
-
Product
Surface Mount Frequency Synthesizers
-
Corech Surface Mount Frequency Synthesizers series packs impressive low phase noise of -90dBc/Hz@1kHz, low spurious of -50dBc to -70dBc, high temperature and corrosion resistance, long operating life, temperature uniformity, and good thermal conductivity. These outstanding performance make it suitable for high-reliability and environmentally stressful applications including communication systems, test and measurement equipment, radar systems etc.
-
Product
Surface Defect Inspection System
-
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
Product
Surface Resistance Meter Kit - Test Anti-Static, Static Dissipative and Conductive Surfaces
PRS-812RM
-
- Surface Resistance Tester from 0.10 Ω to 1 Teraohm- Constant Voltages 10 volts and 100 volts- Automatic Electrification Period- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and resistance to ground (Rtg)- Measures resistance of ESD Flooring, ESD Worksurfaces and Packaging- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Surface Resistance Probes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
Product
Surface Cleanliness
-
Surface cleanliness: Soluble salts & ion specific contamination (sulphates, chlorides, nitrates etc.) which are often invisible to the eye, together with amine blush (for amine cured epoxy coatings) can result in premature coating failure, resulting in high re-coating and maintenance costs. Elcometer has a range of test equipment for assessing surface cleanliness prior to applying a coating.
-
Product
Fixed Writing Surface for Double-Bay 24" RA & RC Cabinets
WS2-124
-
This fixed shelf / writing surface for a double-bay RA & RC cabinets spans the full width of the cabinet and extends 18” in front.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS Basic
-
Optik Elektronik Gerätetechnik GmbH
Low cost contact angle meter provides all functions for DIN conform measurement of contact angle and SFE.
-
-
Product
Automated Surface Inspection for Glossy Components
-
Flawlessly glossy surfaces are among the most important quality features of many premium products. The smallest surface defects immediately have a degrading effect on the product. The result: disappointed end customers or buyers. At the same time, reflective surfaces are often very sensitive and a challenge for optical metrology. A manual inspection is tedious, expensive, and ultimately always governed by subjective decision criteria. During production, faulty painting or coating processes can cause high scrap rates. Defects that are not detected even during the final inspection can lead to expensive complaints and, in the worst case, to the loss of the customer. Only an efficient, automated surface inspection achieves the highest quality at acceptable costs.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS
-
Optik Elektronik Gerätetechnik GmbH
SURFTENS is a Windows image processing software for measurement of contact angle of liquids on solids. SURFTENS contains a calculation module for the surface free energy (SFE) from the contact angles of up to 5 test liquids.SURFTENS software can be used in connection with OEG equipment, but also in connection with existing measuring setups at customer site.
-
Product
Surface Insulation Resistance Testing
-
Following over 2 years of intense research and development, we are proud to introduce the next generation of equipment used to measure changes in Surface Insulation Resistance.
-
Product
Contamination & Clearance
-
Provides the ultimate user-friendly operation, with thorough and reliable detection of external contamination on personnel working in nuclear environments.
-
Product
Surface Paint Quality Scanner
-
Konica Minolta Sensing Americas, Inc
There is always a challenge to achieve a consistent high quality surface on a car body during production. The goal of the manufactures is to reduce defects and, quickly and accurately fix the ones that occur.
-
Product
Continuous Surface Current Mapping & Wave Monitoring System
SeaSonde
-
The SeaSonde HF radar system by CODAR Ocean Sensors is your solution for making continuous, wide-area ocean observations. The SeaSonde will provide you with years of real-time data over large coverage areas, with ranges up to 200 km — This is not possible with any other technology!
-
Product
SMT Surface Mount MEMS High-G Shock Accelerometers
-
Piezoresistive MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
Product
Surface Texture And Contour Measuring Instruments/Systems
-
We provide high performance, easy-to-use systems from highly efficient hybrid types that can measure the surface roughness and the contour in one trace, to portable types that can be used even on the production site.
-
Product
Surface Imaging & Metrology Software
Mountains®
-
Analyze multiple types of surface data. Turn your surface data into accurate, visual surface analysis reports. See every feature with high quality real-time 3D imaging of surface topography. Characterize surfaces in accordance with the latest metrology standards.
-
Product
24" Drawer With Writing Surface, Unshielded, 5.25"H X 30"D
DR-052430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock.
-
Product
24" Drawer with Writing Surface, Unshielded, 10.5"H x 30"D
DR-102430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
ESD SURFACE RESISTIVITY METER (WITH 10 LEDS)
-
Simply place the meter on the surface of the material that requires measuring.Press the green test button. The meter will then light the appropriate LED from 10 to the power of 3 to 10 to the power of 12 Ohms per square or insulative.
-
Product
24" Drawer with Writing Surface, Unshielded, 8.75"H x 30"D
DR-082430-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Surface Resistivity Meter
395
-
The ACL 395 handheld meter features sophisticated circuitry that allows for the same advantages as megohmmeters, but at an economical price. Utilizing color-coded zones, the LED scale is easy to read and evaluate. Half decades indicate where the measurement value falls within the decade giving a closer indication to actual value. Unlike other pocket-sized meters, the ACL 395 features rubber rails which provide the best possible contact.
