Fault
-
Product
PXI 5A Fault Insertion Switch 20-Chan 2-Bus
40-198-002
-
The 40-198 is a 20 Channel Fault Insertion switch, primarily designed for the simulation of fault conditions in automotive/avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
-
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Pre- Locator
CFL PL3+
-
The new generation CFL PL3+ Cable Fault Pre-locator from SCOPE is the ultimate solution for locating underground cable faults in minimum time. It uses advanced technology for fault distance measurement which helps even an unskilled operator to locate the fault accurately up to 128 km.
-
Product
PXI 34-Channel 4-Bus 2A Fault Insertion Switch
40-197A-001
-
This 34-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers. A low cost 16-channel option is also available.
-
Product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
-
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Plastic Fabrications Testing Equipment
-
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
Product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
-
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
DM 150-Watt Transmitter
Loc-150Tx
-
The Loc-150Tx, 150-Watt DM Transmitter is used primarily with the Defect Mapper (DM) Receiver, however it is also useful for those needing a low frequency, high output transmitter. Typically, the Loc-150Tx, transmitter (DM transmitter) is used to apply a signal current to the anode bed. The pipeline returns the signal via coating faults back to the transmitter. The Loc-150Tx transmitter is designed to be powered from CP (Cathodic Protection) stations, AC or external batteries, eliminating the need for internal batteries. This transmitter has a direct connection mode to apply the locate frequency onto the conductor. There is no clamp or induction mode.
-
Product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
-
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
Product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
-
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
Product
Mini Hardened Media Converter, 100Mbps, Multimode 1300nm, LFPT, 5km, SC
IMC-350I-MM
-
Centralized powered IMC-318I chassisSupports Link Fault Pass Through functionality (LFPT)IEEE802.3af compliant (IMC-350I series as PoE-PD)Industrial grade design that supports an extended operating temperature(IMC-350I series)Metal enclosure with compact size
-
Product
PXI Dual Bus 74-Chan 2A Fault Insertion Switch, N/O Through Relays
40-190B-302
-
The Dual Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Product
Vector Network Analyzer
ZNLE
-
The renowned high-quality design, innovative user interface and compact size of the R&S®ZNLE make it ideal for basic VNA applications. The time domain analysis option (R&S®ZNL-K2) and distance-to-fault measurements option (R&S®ZNL-K3) enhance the R&S®ZNLE with essential features for general purpose testing.
-
-
Product
Incremental Transformer Solutions
TRANSPORT X
-
The Kelman TRANSPORT X is a compact portable Dissolved Gas Analysis (DGA) system which can be used to analyze oil samples for all dissolved fault gases and moisture. If abnormal levels are detected, it further provides a diagnostic using various IEEE/IEC approved interpretation rules.
-
Product
Network Management
Neuron System
-
Integrated management: Displaying current status of optical cable installation and location of fault using GIS - Facility management: Establishment of database as to the information of such physical communication facilities as communication device, cable, manhole, and telephone pole.- Recovery management: Enabling quick recovery by sending maintenance personnel to exact location in the event of fault.- Preventive management: Providing preventive measure against fault by prediction of fault due to heat deterioration of optical cable.
-
Product
Crowbar Resistors
-
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Product
Manufacturing Defects Analyzer
eloZ1-400
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1-400 is the compact version of the eloZ1. It is particularly suitable if there is only limited space to fit test appliances. The eloZ1-400 can also be used as a mobile test system.
-
Product
Mini Hardened Media Converter,100Mbps, Multimode 850nm, LFPT, 2km, ST
IMC-350I-M8ST
-
Centralized powered IMC-318I chassisSupports Link Fault Pass Through functionality (LFPT)IEEE802.3af compliant (as PoE-PD)Industrial grade design that supports an extended operating temperatureMetal enclosure with compact size
-
Product
Transient Stability Analysis
I*SIM
-
PTW I*SIM is a program for transient stability analysis. It is designed to simulate system response during and after transient disturbances such as faults, load changes, switching, motor starting, loss of utility, loss of generation, loss of excitation, and blocked governor events. I*SIM is designed to study today's most challenging simulation problems in one convenient and easy-to-use program.
-
Product
Time Domain Reflectometer
STEP TDRS
-
Cable Measurements: Distance, Fault Types, Distance to Faults, Impedance Readings, and Loop Resistance.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A, Hardware Interlock
40-193A-002-HI
-
The 40-193A-002-HI is a 7-Channel Fault Insertion switch with hardware interlock and two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
Product
Hipot Tester
HVA Series
-
HVA systems detect faults in cable networks in a non-destructive yet efficient way and fulfill all the requirements of modern cable testing.
-
Product
Cable Test Vans and Systems
-
Precise cable fault location, testing of new and diagnostic testing of existing cable routes – the BAUR cable test vans are suitable for any operation. Fast and reliable. Exactly adapted to individual requirements and predefined vehicle systems.
-
Product
Fault finder
The STaff™
-
The staff fault finder is designed to meet the demands of the professional troubleshooter but its simplicity and price make it a tool for anyone needing to locate cable faults. Arrows on the LCD screen direct the user to the fault with pinpoint accuracy. A reference indication also will aid the user in identifying multiple faults when present. Whether you are fault locating utility service line or locating a broken sprinkler wire, the STAFF is the professional's choice.
-
Product
Surge Voltage Generator
SSG 2100
-
Cable fault location with the BAUR SSG 2100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
Battery Fault Insertion Unit
-
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Integral Intelligent Flame Detector
FS-100
-
FS-100 utilizes SMT technology which integrates a photoelectric sensor, a microprocessor, and a Human-Computer Interface (HCI) and an output interface together, sending out various outputs including an ON/OFF flame signal, a fault signal, a 4-20mA signal, and an RS-485 output (meets the MODBUS standard) via the quick connector.
