Attenuation
-
Product
Coaxial Attenuators Set
11583C
Attenuator
The Keysight 11583C contains a set of four 8493C attenuators 3, 6, 10, and 20 dB furnished in a handsome walnut accessory case. The Keysight 8493C are APC-3.5 connectors with a maximum frequency of 26.5 GHz. This set is ideal for calibration labs or where precise knowledge of attenuation and SWR is desired.
-
Product
KW Phase Array Radar Jamming System C, X, Ku, K, Ka And V Band
-
Digital Step Phase Shifter. Digital Step Attenuator. RF Solid State High Power Switch. Front End Low Noise . mplifier for Feedback. Transmit Solid State Power Amplifier Matrix 4x4, 8x8 or 16x16. Ultra Wide Band Flat Panel Antenna. Rotary Joint 360 rotation capability.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Programmable Step Attenuator, DC to 26.5 GHz, 0 to 70 dB, 10 dB steps
84907K
Attenuator
The Keysight 84907K programmable step attenuator offers coaxial measurements to 26.5 GHz in a compact, rugged design. It offers repeatability of better than 0.03 dB, excellent life (greater than 5 million switching cycles per section) and an attenuation range of 0 to 70 dB in 10-dB steps. This latest design evolution sets new standards for size and performance. High attenuation accuracy and low SWR are achieved through the use of miniature thin-film attenuation cards composed of high-stability tantalum nitride film of saphire substrate. Insertion loss is outstanding, with less than 2 dB of loss at 26.5 GHz. The compact size of the unit, 35 percent smaller than the Keysight 8495/7 26.5 GHz) family, allows for easy integration into instruments and ATE systems.
-
Product
Pulse Characterization Sensors
-
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
Product
Variable Optical Attenuator Module with Angled Interface
81571A
Optical Attenuator
The Keysight 81571A variable optical attenuator features lowest insertion loss and excellent wavelength flatness over a complete attenuation range of 60 dB, for characterizing optical network components for telecommunication and data communication in systems.
-
Product
Variable Attenuators
-
Continuously variable attenuators from Pasternack are available in 50 Ohm impedance and with SMA connectors. SMA continuously variable attenuators have RF db attenuation values that range from 7 dB to 40 dB. The frequency range of our continuously variable attenuators is from 1 GHz to 18 GHz. This variable attenuator product line includes low to high power attenuators which have the power handling up to 5 Watts.Variable attenuators from Pasternack include female genders and can be bidirectional, depending on the power rating. Our continuously variable attenuators are manufactured to precise industry specifications and the bodies are constructed of. Pasternack commonly uses Pi attenuators or Pi pads for its continuously variable attenuator designs.
-
Product
Variable Optical Attenuator
-
Shenzhen Golight Technology Co.,Ltd
Variable optical attenuator uses high-precision attenuation control components, and combines a selfdeveloped embedded data processing platform and precise calibration process, can be provided with maximum 60dB optical power attenuation and optical power monitoring function. Real-time display of input and output optical power.
-
Product
Coaxial Fixed Attenuator, DC to 67 GHz
8490G
Attenuator
Keysight's 8490G precision coaxial fixed attenuators maximize your operating frequency range up to 67 GHz by providing industry-leading attenuation accuracy, coupled with low SWR and a variety of attenuation options to suit your application needs. The attenuator is available in attenuations of 3, 6, 10, 20, 30 and 40 dB. The 8490G is swept-frequency tested to ensure it meets specifications at all frequencies.
-
Product
Economical Solution for Test Requiring Fewer Instrumentation Modules.
OPTOWARE-S200 (FOTS-Bench Top Series)
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
Fixed Attenuators
-
BroadWave attenuators reduce the strength of an RF signal without appreciable distortion of its waveform.
-
Product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
-
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
Product
3-Channel LOW PIM Attenuator
-
Corry Micronics' 3 channel, LOW PIM attenuator covers the 400 to 3000 MHz frequency range and has been specifically designed for major mobile access carriers who are attempting to measure or monitor passive intermodulation distortion/interference in communications systems.
-
Product
Termination
WTER-3N30
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Coaxial Fixed Attenuator, DC to 18 GHz
8491B
Attenuator
The Keysight 8491B coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. It has type-N connectors with a maximum frequency of 18 GHz. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
Product
Flexible Cable Assembly
WCBA-WC03SM.SM1
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Lowpass Filter/SMA
WFIL-L700F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Adapter/Stainless Steel
WADP-NFNF-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
SP200B, 200 MHz, ±60 V, 1X or 10X Attenuation, Single-Ended Passive Oscilloscope Probe
780284-01
Oscilloscope Probe
The SP200B is a standard switchable passive probe for oscilloscopes that provide 1 MΩ input impedance. Depending on the attenuation ratio, the probe has an analog bandwidth of 6 MHz in the 1x attenuation setting or 200 MHz in the 10x attenuation setting.
-
Product
Adapter/Stainless Steel
WADP-QSMSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Adapter/Stainless Steel
WADP-24M29F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Millimeter-wave and Microwave GaAs Attenuators
Attenuator
Keysight Technologies provides MMIC attenuators ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
Product
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory
HVFO100-40X-TIP-U
-
HVFO10X +/-40V (40x Attenuation) Universal Tip Accessory.
-
Product
RF Attenuators
-
Bird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
Variable Optical Attenuators
-
A fiber optic variable attenuator is used to reduce the power level of an optical signal in fiber optic communications.
-
Product
Attenuators
-
A device consisting of an arrangement of resistors which reduces the strength of a radio or audio signal.
-
Product
PXI Attenuator/Switch Driver Module
M9170A
Attenuator
The Keysight M9170A is a one-slot PXI attenuator switch driver module that provides the flexibility to drive Keysight's expansive portfolio of RF & microwave step attenuators and electromechanical switches. It is a PXI-hybrid compliant module that comes with a full-featured graphical interface soft front panel for easy control and trigger.
-
Product
PXI Dual RF Attenuator, 2.3GHz
41-181-022
Attenuator
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
Product
Adapter/Gold
WADP-SMSM
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PXI Hybrid Amplifier/Attenuator
M9352A
Attenuator
The M9352A modules are custom built and tested to nominal* performance characteristics. Full regulatory and safety testing has been performed. This product has the same warranty and support services as other Keysight instruments. Because it is custom built, Keysight recommends checking availability and delivery information before ordering the product.
