HIgh Current
-
-
Product
Standard - 1.44 (41.00) - 4.50 (128.00) High Current Probe
HCP-13A
High Current Probe
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Standard - 1.44 (41.00) - 4.50 (128.00) High Current Probe
HCP-13P
High Current Probe
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Rogowski AC Current Probe, 23 MHz, 3000 A
N7040A
High Current Probe
The Keysight N7040A Rogowski coil current probe is designed for measuring AC currents up to 3,000 A with the bandwidth ranging from 3 Hz to 23 MHz. The probe is easy to use because it has a thin, lightweight, flexible and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult to reach parts and confined spaces of a circuit under test. It can also measure large AC current without increase in transducer size.
-
Product
High Current / High Temperature Spring Probes
-
We have spring probes, which can be used for high temperature and high current test under 200 degree and shows high performance in them.
-
Product
High Voltage Film Capacitor
STHVP/STHVE
-
High Voltage Pulse Current for medium frequency applicationHigh Voltage DC / AC Voltage applicationCapacitor can be discharged at rated voltage directly without any protective component and with ambient Temperature up to +105CHigh Voltage Decoupling and SnubberingVoltage MultiplierInduction heatingAct as discharge capacitor to trigger laser, X-Ray and Tesla CoilFor high voltage capacitor bank or arrayHigh Voltage Power Supplies
-
Product
High Current Calibrator
MC151
-
MC151 Current calibrator is an accurate current source capable of 120 A. Typical uses include calibration of current sensors, current probes, current transformers, shunts, ammeters, DMMs or as stable current source for test and development applications. The calibrator is equipped with a built-in multimeter that can be used for simulation of programmable transconductance or current amplifier.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Portable 4-Quadrant Power Amplifier
PIV270
-
PONOVO POWER's PIV270 Power Amplifier is equipped with feature of high power, large current, high voltage, high precision, high speed etc. It can meet different application on power and precision requirements.
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
-
Product
Current Probes
XQ13
-
Beijing GFUVE Electronics Co.,Ltd.
The model XQ13 ac micro amp clamp on current probe is suitable for 10A-100A cable online measurement, it belongs to high performance current sensor field.
-
Product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
Switch Module
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
-
Product
PXI High Power General Purpose Switch Modules
-
Pickering's PXI high power general purpose switch modules provide a range of high current handling relays suited for high power applications. Lower current versions require one 3U PXI slot, the highest current versions occupy two slots. These modules can be used to switch heavy AC or DC loads and the highest current versions are particularly suitable for automotive test. We also have high power switches available in multiplexer and matrix configurations.
-
Product
PXI Solid State Matrix Module, 6x2, 30 A, Hardware Interlock
40-554B-011-HI
Matrix Switch Module
The 40-554B-011-HI is a high current 6x2 matrix with hardware interlock occupying two PXI chassis slots. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI Digital IO: 32 inputs, 32 outputs, 0.3V to 50V
M9187A
Digital I/O Module
The M9187A has 32 input channels that can be used for comparing inputs to user-defined thresholds between 0.3V and 50V, with 12mV setting resolution. Each input is protected up to 100V. In addition, the 32 output channels use a high current to drive the output high or low, and are capable of sourcing 0.4A from the high side or 0.5A sink from the low side of each channel. These outputs are protected against over-voltage or over-current conditions. Choose from the durable connector block or the standard cable connections.
-
Product
Standard -1.44 ( 41.00) - 4.50 (128.00)High Current Probe
HCP-13B
High Current Probe
Current Rating (Amps): 15Average Probe Resistance (mOhm): 25Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 250,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
PXI BRIC8 FIBO Matrix Dual 30x4 3pin brkout
40-595A-010
Matrix Switch Module
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
Product
Test & Test Development for Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions performs comprehensive testing at the CCA and system level assembly. Teledyne AES can perform testing developed by the customer or develop a complete test strategy for the customer’s products.- Bed of Nails FixtureIn-Circuit Test (Bed of Nails) or Flying Probe Testing for rapid feedback on CCAs- Functional testing of CCAs or complete systems- Environmental testing to include vibration, thermal cycling, HASS, etc.- CCA and system level test development- High frequency testing – currently to 40 GHz- High power system testing – currently to 4kW
-
Product
USB Charger
-
PeakTech Prüf- und Messtechnik GmbH
This practical table power strip offers two safety sockets with child protection and two USB charging ports with a high maximum charging current. There is a shelf for smartphones and tablet PCs on the front, which, thanks to its slightly angled shape, enables excellent usability of the device. The non-slip rubber nubs on the bottom prevent slipping on the work table, with an integrated blue LED as a power indicator.
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
Transmission Line Pulse Testing
-
Transmission Line Pulse testing, or TLP testing, is a method for semiconductor characterization of Electrostatic Discharge (ESD) protection structures. In the Transmission Line Pulse test, high current pulses are applied to the pin under test (PUT) at successively higher levels through a coaxial cable of specified length. The applied pulses are of a current amplitude and duration representative of the Human Body Model (HBM) event (or a Charged Device Model – CDM – event in the case of Very Fast TLP, or VF-TLP).
-
Product
PXI 32 Channel I/O Serial I/P Prog Threshold
40-412-001
Digital I/O Module
The 40-412 is a 32-channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low using a high current capacity drive capable of sourcing 0.4A from the high side or 0.5A sink on the low side for each channel. The module is available in two versions with either serial or parallel capture of the input levels
-
Product
Mini 4 Block Desktop Receiver
VGR4
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250VAC/5Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Digital Multimeters
-
6 Functions (AC/DC Voltage, AC/DC Current, Resistance and Diode Test) - 4 1/2 Digits - High Resolution 10V, 10nA - High Current Range 10A - High Voltage Range 1000V - All Range Protected"
-
Product
PXI Solid State Multiplexer, 10 Amp, Single 6-Channel
40-666A-012
Multiplexer Module
The 40-666A-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Combination Board Tester
-
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
12-Ch SPST 5A-250VAC High Current Power Switching
YAV90CIN
Switch Module
12 Independent SPST relaysSwitching up to 5A 250Vac12 current measurement channelsGeneral inhibit inputCAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
