Non-contact Voltage Testers
check for presence of electricity.
-
Product
Voltage Protection
-
Are solid state voltage sensing relays with electromechanical output contacts built in a fully draw out case format. Designed for application on AC & DC voltage systems, these relays are ideally suited to monitor power supply voltage levels wherever high accuracy and reliable, maintenance free operation is essential. All power to operate the relays is derived from the sensed input voltage therefore an auxiliary supply is not required.
-
Product
Dual High Voltage Power Supply Tester
MS 1110
-
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
-
Product
Voltage Integrated Sources
VIS
-
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
Product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
Complete Non-Contact Inspection System For OLED/TFT/LTPS
GX3/GX7
-
*Fastest*Workable to large panel as well as fine pattern of medium-small panel*Workable to large mother glass of every generation*Possible to dock width Repair Machine
-
Product
Retractable Cable + Automotive Voltage Tester With Magnet Adsorption
3703
-
Peaceful Thriving Enterprise Co Ltd
*Check on 6, 24 and 48V DC systems.*Used as an extension cord for testing electrical circuits in cars , trailer, boats.
-
Product
Dual-Range High Voltage Non-Contact Tester
HVNCVT-1
-
Use to check for the presence of voltage in overhead conductors or find faults in cables.LOW range for 50V AC to 1.5kV AC.HIGH range for 1.5kV AC to 132kV AC.Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case.
-
Product
Non-contact Ultra-High Range Sheet Resistance Measurement System
CRN-100
-
*Ultra-High range sheet resistance measurement for 10E+9 ~ 10E+15 ohm/sq without contacting*Mapping program software;*1. Arranged in a multipoint pattern measurement is programmed*2. 2-D & 3-D mapping software*Easy operation by Windows 7 system software*Measurement data base link with Excel via CSV format file*Unaffected by contact resistance
-
Product
Non-Contact Beam Profiler
BeamWatch
-
The patented BeamWatch non-contact profiling system accurately captures and analyzes industrial multi-kilowatt lasers wavelengths from 980nm - 1080nm by measuring Rayleigh Scattering. It features a complete passthrough beam measurement technique, no moving parts, and a lightweight compact design which makes it ideal for comprehensive analysis of industrial multi-kilowatt lasers
-
Product
High Voltage Probe
HVP-40M
-
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
Product
Current And Voltage Input Sensors
-
Current input sensors monitor current from inverters in solar panel and wind turbine applications and turn the current into voltage which can be measured with an analog input type data acquisition module for analysis. Voltage Input Attenuators can be used to measure high voltages. Voltage Attenuators are designed for used in high-voltage applications. The current can be converted into +/-10 Vpp attenuated signal, so that a general electronic measuring device is able to read the signals.
-
Product
Voltage Output D/A Converters
-
Analog Devices offers a large family of resistor string and R-2R voltage output (VOUT) D/A converters (DACs). From 8 bits up to 20 bits of resolution, single to 40 channels, integrated or external reference, parallel, LVDS, serial SPI or I2C interface, with high temperature operation, we have a D/A converter to suit your application. We provide precision, buffered, and unbuffered rail-to-rail VOUT D/A converters with up to ±1 LSB INL and DNL specifications and excellent offset and gain error. Our D/A converters work well in a wide variety of open-loop or closed-loop systems—adjusting gain, offset, and many other signals.
-
-
Product
Voltage Logger Sensor
NUL-201
-
This sensor measures voltages across various resistive, capacitive and inductive components, as well as those of photovoltaic cells, batteries and power supplies. This sensor can also be used to measure electrode potentials and to investigate the charging and discharging of capacitors.
-
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
Product
LXI High Voltage Switching
65-233-902-HI
Switch Module
The 65-233-902-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Voltage Indicators
-
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
Product
Power Supply Voltage Generator
MON12
-
*The mezzanine MOH12 is a module designed to generate supply voltages through twelve galvanically isolated channels.*The MOH12 mezzanine is installed on the mezzanine carrier - the NM-M (NMU) module and is connected to it via a local information highway. Up to four MOH12 can be installed on the NM (NMU) module.*The NM-M (NMU) module together with the mezzanines installed on it forms a VXI module of the C-1 size and is used to create information measuring VXI systems.
-
Product
High Voltage Amplifier
HA-400
-
*400Vp-p(±200V DC) *160mAp-p(±80mA DC) *Bandwidth: ≦600KHz(200Vp-p) *Slew Rate: 300V/us *Gain(AMPL): 0~90(10 Turn VR) *DC Offset: ≦0~±200V (10 Turn VR + SW) *Output Resistor: 50Ω
-
Product
Voltage Breakdown Testing Machine
DRK218
-
Shandong Drick Instruments Co., Ltd.
DRK218 breakdown voltage tester is controlled by the computer, through a new smart digital integrated circuits developed by my company and software control system to make the step-up rate is truly uniform, accurate, and be able to accurately measure the leakage current data. Real-time rendering test curve accurate judgment and it can save, analyze and print test data.
-
Product
Non-Contact Displacement Sensing System
KD-2306
-
Multi-purpose non-contact position/displacement sensing* Supports both dual and single coil sensors* Terminal I/O connections* Auto-synchronization of multiple channels* Analog DC and 4-20mA outputs* Single ended, bipolar, and differential voltage outputs* Front face coarse and fine calibration controls* RoHS compliant and CE marked
-
Product
High Voltage Linear Amplifier
A400X
-
This unit is a version of A400 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A400X functionally identical with A400 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Installation Tester
M74
-
M74 measures Overall earth resistance, tripping time of RCDs type AC, Insulation and Continuity of earth and equipotential conductors according to the laws in force in private electric installations.
-
Product
AC/DC Programmable Hipot Voltage Insulation Tester 5KV
7122
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC Hipot & Insulation Resistance Tester can do hipot test and insulation resistance test
-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
-
Product
Speedometer/Taximeter Testers
-
Machines for checking the accuracy of speedometers, taximeters, speed limiters, speed warning devices. As with most VLT equipment, these machines can be used stand-alone, or in an integrated test lane.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
