POT
Measure the voltage in a circuit or function as voltage dividers.
-
Product
Hi Pot Meters
-
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
Product
Connector Test
-
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
Product
IEC60335-2-9 Clause 3 Figure 104 Vessel For Testing Induction Hotplates
CX-104
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
IO-Link Hubs
-
- For the simple connection of binary sensors to any IO-Link master- Uses industry standard M12 unshielded patchcords- Clearly visible LEDs for displaying operation, switching status and error- Robust design with full potting for use in harsh industrial environments- Robust M12 connectors for connecting sensors and actuators
-
Product
COMPUTERIZED LCRTZ TEST SYSTEM (Automatic Transformer Test System)
CVCT-S20
-
Ideal for fast and fool proof testing of COILS AND SMALL TRANSFORMERS like SMPS transformers, Telecom transformers (HYBRID, POT CORE, RM-CORE), Pulse transformers etc. The systems scans at one stroke, all the windings of a transformer and tests as per definition of test procedure. The test procedure can be pre-programmed and stored under User friendly menu driven software . Any semi-skilled and unskilled person can be engaged for actual testing purpose. Can Select test frequency, pin number, parameters, test conditions, limits for each test. Test any pin to any other pin any defined parameter.Test Parameters :-> Inductance-> Capacitance-> AC Resistance, -> DC Resistance, -> Impedance, -> Leakage Inductance,-> Transformation Ratio & Winding PolaritySPECIFICATIONS :Measurement Frequencies : 50 Hz, 100 Hz, 500 Hz, 800 Hz; 1 KHz, 2 KHz, 5 KHz, 10 KHz. Measurement Voltage: 0.1 V – 1.0 V RMS adjustable under program control.
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
DCDC
FC Series
-
The FC Series are ultra-low noise, high performance DC/DC converters that are packaged in low profile (0.4 inch high) cases. Essential quality performance features are designed and built-in. A high performance Pi input filter minimizes input reflected ripple, while 5-sided electrostatic shielding and tape-wound toroids, rather than pot cores, minimizeradiated EMI. Advanced circuit design techniques reduce conducted output noise in the form of current spikes, to an extremely low level.
-
Product
Neon Transmitter
-
Shanghai Yiya Electronic Instrument Co., Ltd.
Asphalt resin filled and vacuum potted. Patented magnetic core at low consumption. Heavey duty metal box and coated power. User Friendly-Adapts to most grounding situations.
-
Product
Time Code Distributor/Reshaper
SR-112
-
Like it’s big brother the SR-112 Distripalyzer, the SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Product
UV Sensors
-
The patented domed shaped sensor head facilitates runoff of dew and rain, helping to keep the detector clean and minimizing errors caused by dust blocking the radiation path. Sensors are housed in a rugged anodized aluminum body and electronics are fully potted.
-
Product
DC Electronic Load
EE30181A
-
The EE30181A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current
-
Product
Radiographic Inspection Test
-
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
-
Product
Analog Input Modules
-
The modules provide direct connection to a wide variety of sensors and annunciators. They perform all signal conditioning and linearization and contain no pots or DIP switches. All user-selectable settings, such as ranges are stored in nonvolatile EEPROM, which maintains these values even after power is removed.
-
Product
Precision Pots Single-turn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. Theses devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available.
-
Product
Remote Slab Sensor and Outdoor Temperature Sensor
CHV-RSS
-
The CHV-RSS is a remote temperature sensor designed for use with select Crestron thermostats. Ideally suited for concrete slab, under floor, or any outdoor installation, the CHV-RSS is an extremely accurate temperature sensor potted within a rugged waterproof stainless steel sleeve.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Input / Output Modules
-
*Competitive cost-per-channel*24-bit A/D converters; 16-bit exported*ICP, Strain Gauge, Frequency, String Pot, Thermocouple*Portable, rugged, stand-alone operation*Open-source command set for third-party software applications
-
Product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
-
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
Product
Surge / DC Hi-Pot Consoles
HC Model
-
(Surge / Hi-Pot Consoles) - Now available in High Voltage models - 35,40 & 50KV. The HC Model offers Surge / DC Hi-Pot testing capabilities! The "HC" Model has all of the features of our "C" Model plus a DC Hi-Pot Tester. DC Hi-Pot includes dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip and the capability of ascertaining Polarization Index (PI) Test results.
-
Product
50 Ohm Bridge / Freq Counter
-
* Generates a 3 to 30 MHz low level signal displayed on small 8 x 2 LCD * 50 ohm bridge supports tuning 50 ohm antennas * Adjust POT to find the resonate frequency of antenna * 30 turn POT allows easy smooth frequency adjustment * Bright red LED extinguishes when bridge is balanced * Function switching allows for use as frequency counter * 50 ohm termination included * measures 5.5 x 2.5 x 1.1 inches * 9 volt battery operation
-
Product
Time Code Reshaper/ Distributor
SR-28
-
The SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Product
Hi-Pot Tester
DU3315A/3316A
-
Delta United Instrument Co., Ltd.
Real-time Open Check of the alarm and signal output of no contact signal3 in 1 tester with AC, DC, IR functions ( IR function is optional for DU3316 only)ARC Detction:DU3315A /DU3316A Standard function40 x 4 LCD text displayFast cut-off time : 0.4ms5 sets of memory, 3 steps for each memory
-
Product
Limit Alarms
-
Process limit alarms monitor sensor or process current input signals and trip a relay output if the input exceeds a user-defined hi/lo setpoint limit. Select from AC-, DC, and loop-powered models. Configuration is easy with Windows software, push-buttons, switches, or pots for settings depending on the series.
-
-
Product
DC Electronic Load
EE15120A
-
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
Product
5kv 10kv hi-pot tester
RK2671
-
Shenzhen Chuangxin Instruments Co., Ltd.
5kv,10 kv hi-pot tester withstand voltage tester KR2671 Voltage tester high quality
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
IEC60335-2-9 Clause 3 Figure 103 Vessel For Testing Hotplates
CX-GZ
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 103 Vessel for testing hotplatesParameter:1.Pot and lid material industrial aluminum2. Pot material thickness 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm;4. Pot body and lid surface should be smooth;5, size: 110, 145, 180, 220, 300mm each one
-
Product
Signal Conditioning & Control
-
Offering a wide variety of products from amplifiers and comparators to redrivers, microcontrollers, data converters (ADC) and digital potentiometers (POTs).
