-
Product
Intelligent Power Switches
-
ST offers a series of intelligent power switches (IPS) for high-side and low-side configurations. These devices integrate the control section (logic interface, drivers, diagnostic and protection features) and the power stage on the same chip, with benefits in terms of compactness, increased system reliability and cost effectiveness.
-
Product
Protected & Intelligent Power Switches
-
Single/Dual high-side output with optimized protection function and analog current feedback for body, lighting and heater applications.
-
Product
Power Switches
SMX-2002 (Power)
-
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
Product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
Switch Module
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Intrinsically Safe Relay
SSR-15
-
Model SSR-15 Intrinsically Safe Relay offers low power switching with solid state reliability and eliminates explosive conditions. Units are completely encapsulated and impervious to dust, moisture, or foreign material. Model SSR-15 can be mounted in any orientation and is shock and vibration resistant
-
Product
Linear AC Power Supply
-
Applicable places : equipment testing, compressor testing, monitor testing, motor equipment testing, air conditioning equipment testing, optimal power supply for R&D units, testing of various electrical products, 400Hz power supply for military equipment, special power supply for switching DC power supply testing, transformer /TRIAC / SCR...
-
Product
PXI 10x4 Matrix 2A 1 Pole
40-545-001
Matrix Switch Module
The 40-545 series of modules are high density power switching matrices. Typicalapplications include power routing in Functional ATE systems, specifically automotiveelectronics, for example testing of Engine Management Units.
-
Product
PXI High Power General Purpose Switch Modules
-
Pickering's PXI high power general purpose switch modules provide a range of high current handling relays suited for high power applications. Lower current versions require one 3U PXI slot, the highest current versions occupy two slots. These modules can be used to switch heavy AC or DC loads and the highest current versions are particularly suitable for automotive test. We also have high power switches available in multiplexer and matrix configurations.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
Water Level Controller with Timer & Overflow Sensors
IM1730
-
Ajinkya Electronic Systems provides water level controller which is most popular in housing societies. Water is a precious natural resource and it’s our social responsibility to save water whenever and wherever possible. In cities we get treated water and which makes it more precious. So there is a need to use this resource judiciously and carefully. In societies there are overhead tanks which gets filled periodically from the underground tank. The prosess requires man power for timely switching off the pump to avoid dry running as well as overflow of the water. The water level controller for societies offers a smart solution for pumping of the water to overhead tanks in buildings
-
Product
EDFA
SPA-2-4X22-WDM EYDFA
-
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
Product
Amplifier
C-Band
-
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
Product
Switches-DPDT
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
PXI High Voltage Power Multiplexer, Hex 4:1 (SP4T)
40-331A-004
Multiplexer Module
The 40-331A-004 hex 4:1 MUX is part of our range of 40-331A/332 High Voltage Power Multiplexer and Matrix Modules and is suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching.
-
Product
DC Power Supply
-
The main products of DC Power Supply are divided into four categories: linear DC power supply, programmable DC power supply, switching DC power supply, and DC power supply, which are subdivided into single output/dual output /Four sets of memory dual output/ high voltage/high power/high resolution/four sets of memory dual output/dual range/customized specifications and other DC power supplies are available for you to choose and use the appropriate DC power supply to get the best results. Best noise performance and device protection.
-
Product
PXI Mixed Configuration Relay Module - 13 Cells Populated
40-138-AA-BB-CC-DD (13 CELL)
Relay
The 40-138 2A Relay Module with 13 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
100-Watt DC/DC Converter, 3U cPCI
55LQ2
DC Converter
NAI’s 55LQ2 is a 100 Watt DC/DC Converter that plugs directly into a standard 3U cPCI chassis with a 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This modular, switching power supply accepts +28 VDC input and provides a single output at up to 100 Watts.
-
Product
PXI Single 24:1 High Voltage Power MUX
40-331-001
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Precision Programmable Regenerative Grid Simulator, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Sequoia Series
-
AMETEK Programmable Power, Inc.
The California Instruments Sequoia Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of the-art SiC power switching architecture, this full four quadrant product combines compactness, robustness, and functionality in a floor-standing chassis.
-
Product
Chassis - up to 8 8x1 Modules, 16 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration for up to 64 Relay Drives
CXM/64-MF
Chassis
These Chassis controls up to 8 8x1 modules, 16 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 64 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
PXI 6xSPDT 16A Power EMR Module
40-161-102
Relay
This40-161 range of PXI power relay modules is available with achoice of 16 x SPST, 12 x SPST, 10 x SPST, 12 x SPDT and 6 x SPDT power relays, for switching loads up to 16A at250VAC. These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
Chassis - up to Sixteen 8x1 Modules, Thirty Two 4x1 Modules or Any Combination or Configuration of 8x1's, 4x1's, 2x1's and 2x2 Modules
CXAR/128-MF
Chassis
These Chassis controls up to sixteen 8x1 modules, thirty two 4x1 modules or any combination or configuration of 8x1's, 4x1's, 2x1's and 2x2 modules. LEDs on the front panel show switch and power status. Add Switch Modules, CP8 Driver Modules and a Control Module to complete the system. Keypad Manual manual control with LCD display is optional.
-
Product
LED Floodlight up to 6000m, 120Vac 10,000 Lumen
U Light
-
The Teledyne Bowtech U light is for use on subsea platforms that operate down to 6000m depths, requiring a 120Vac Ultra- bright 10,000 lumen, LED Floodlight. The 80° wide LED floodlight beam angle is ideal for colour video inspection tasks. Housed in hard anodised aluminium, this deepwater LED floodlight measures in at 82mm Ø by 148.4mm long and comes with thermal protection ensuring that the light does not overheat if accidentally run in air. The U Light has the capability of being controlled externally by normal ON / OFF power switching or by using phase control diming techniques enabling the operator to produce a varying level of light intensity. This extremely robust U Light LED floodlight is ideal for clear visibility in deep depths on larger work class ROVs, Trenchers and Tractors.
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
Matrix Switch Module
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
Bench Power Supply, Single, Adjustable, 1 Output, 1 V, 60 V, 250 mA, 1.6 A
72-8340A
-
The 72-8340A is a 100W switching mode laboratory grade Power Supply with current limiting control, is designed with the objectives of high accuracy, compactness and easy portability. 4 digit display LCD of voltage and current for high precision. The slim tower housing makes it ideal for tight work bench. It is light and conveniently portable with a collapsible handle. The large and illuminated LCD display provides clear and sharp readings even under dim light. The output power on off switch allows safe and handy operations. The tracking OVP (output over voltage protection) ensures a better and tighter protection to voltage sensitive loads. It has good line and load regulations, high efficiency, low ripple and noise that are typical of advanced switching mode power supply.
-
Product
Multiport Power Meters
-
The N77-Cs have a family-wide, common trigger concept, and a modern, browser-accessible user interface, making it convenient to configure the instrument’s functionality. High-speed measurement data acquisition, faster data interfaces, the use of dual-ported RAM for uninterrupted simultaneous measurement and readout, and fast power range switching help avoid unnecessary delays in the measurement process as well as in post-processing.
-
Product
Power Switches With USB Charge Controller
-
ST’s USB charger emulator family (STCC) features ICs integrating a power switch, a data switch and an intelligent charge controller. It supports most charging schemes on the market (standard and proprietary) to ensure compatibility with a broad range of portable devices. ST’s unique and patented attach detection mechanism makes the STCC family ideal to guarantee fast and accurate charging while preserving the host battery.
-
Product
Integrated Current Sensors
HMSR series
-
The HMSR is a new generation of high insulated Integrated Current Sensor from LEM. These product family provides a robust, compact and very accurate solution for measuring DC and AC currents in all highly demanding, switching power applications for commercial, industrial. HMSR is a micro core based open loop sensor with a reinforced insulation and overcurrent detections (user configurable and factory set). These features make the device suitable for high voltage applications requiring high precision and strong immunity against external field. The primary conductor (pins 1 and 8) has very low electrical resistance and dedicated pads d
