Geometry
-
Product
RANGER-ULTRA
-
The RANGER-ULTRA is an airborne laser scanner with an impressive combination of weight, range, accuracy and pulse rate. It is equipped with a unique forward and rear looking FOV designed to minimize laser shadowing and provide geometry on complex vertical structures on a single pass. With its wide field of view of 100 degrees and an extremely fast pulse repetition rate of up to 1.8 MHz, the RANGER-ULTRA is perfectly suited for high point density corridor mapping applications such as power line, railway track and pipeline inspection.
-
Product
Impedance Measurement
CITS880s
-
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
Product
Camera Testing
FLIR
-
CI Systems' FLIR turn-key test stations carry out all the necessary tests to verify and compare the quality of an infrared/thermal camera. The FLIR test systems are based on CI Systems' NIST traceable blackbody radiation sources, collimators and special thermally controlled targets, designed to provide very accurate IR test patterns. All these combine to project standardized targets with known geometry and intensity to the Unit Under Test(UUT).
-
Product
Inspect a Large Range of Part Geometries
ECHOMAC® PA Composite Tester
-
ensures complete inspection of the part. The system is scalable, allowing the flexibility of adding channels as needed to handle a large range of part geometries. Meets or exceeds USA, European and other international specifications in aerospace and automotive industries. MAC can supply mechanics designed to meet customer requirements ranging from inline bubbler systems to stand alone immersion tanks with part placement.
-
Product
Checking the Geometry and the Placement of the Weld
-
Based on the real geometric three-dimensional profile of the weld (groove) on the outside of a large diameter pipe, determine the offset of the center of the weld (groove) from the weld line. Provide continuous output of results through the RS-232 interface to the welding process control system. Provide a graphical picture of the current profile, the values of the specified and calculated geometric parameters to the operator.
-
Product
Step Probes
Step Probe
*Precisely controlled probe travel*Step tip geometry*Replaceable and non-replaceable versions*Plating options available
-
Product
Rotating Machinery
-
Synchronize rotating machinery data with a corresponding RPM signal to understand the RPM-dependant vibrational behavior of your measurement object. The package includes Order Analysis for performance optimization of your rotating machinery. Create your structure's geometry with just a few clicks to animate the structure's vibration behaviour. This offers the very unique possibility of an Order Operating Deflection Shape (ODS) analysis.
-
Product
XRD System
SmartLab®
-
SmartLab includes as standard Rigaku's patented Cross Beam Optical™ (CBO) technology. CBO technology uses simultaneously mounted, simultaneously aligned optical components for both focusing (Bragg-Brentano) and parallel beam diffractometer geometries. Users can switch between the two geometries without the need to remove, replace, or realign optical components.
-
Product
Turret Kelvin Test Contactor
cHybrid
-
cHybrid™ Kelvin contactor contains a new and unique contact spring architecture which allows the test socket to adapt to challenging IC pad geometry requirements of todays and future small package types. Great lifetime up to 3 million touchdowns, with best-in-class contact resistance repeatability reduces cost of test significantly. A multi-beam contact structure optimizes signal integrity and current capability according to challenging electrical test requirements.cHybrid Kelvin contactor with multi-beam contact spring architecture delivers improved yield and long life minimizing cleaning cycles. This innovative solution will help customers reduce cost and maximize productivity.
-
Product
WATOM
-
Wafer edge and notch profile measurementThe use of smaller and smaller patterns in the semiconductor industry calls for increasingly advanced materials of extremely high quality. In response to the steady improvements in the quality of wafers, KoCoS Automation has developed WATOM, a wafer edge and notch profile measurement tool which heralds a new era of extremely precise wafer geometry measurement.WATOM supports quality assurance throughout the wafer manufacturing process, starting at the very beginning and continuing on through to wafer reclaim.The WATOM Edge and Notch Wafer Geometry Analyser sets the worldwide benchmark for the quality assurance of geometrical measurements in semiconductor wafer manufacturing, combining the highest quality standards with top-class service. These high-precision, laser-based edge profile measurement tools are specially designed for optimum integration in manufacturing lines within the semiconductor industry.
-
Product
Pneumatic Flat Grips
-
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
Product
UltraScan PRO Spectrophotometer.
Spectrometer
Hunter Associates Laboratory, Inc.
The D65 illumination source is calibrated in the ultraviolet region for the accurate measurement of whitening agents. UltraScan PRO has an extended wavelength range into the near infrared and near ultraviolet that permits the measurement of camouflage materials and UV blockers. The system uses diffuse/8° geometry with automated specular component inclusion/exclusion. It also features three sizes of sample measurement areas with automated lens change. The UltraScan PRO includes EasyMatch QC software and an electronic record keeping version that is 21 CFR 11 compliant is available.
-
Product
3D-IC Solution
-
Consumer demand for increased bandwidth and low power in smaller form factor has forced design teams to pursue design and manufacturing alternatives to single system-on-chip (SoC) approaches. Moving to advanced geometries like 20nm/14nm is a natural progression; however, it has its own cost, yield, manufacturing, and IP reuse challenges.
-
Product
Front-end
-
With geometries getting smaller, macro inspection becomes both more challenging and crucial for defect-free and high-yield wafer manufacturing. The variety of defects calls for detection optimization, fast screening and categorization of the high volume manufacturing environment, while maintaining high throughput.
-
Product
Automated XY Stage
AT2
-
The Instron AT2 is a compact automated XY stage that streamlines compression, tensile, and flexural testing for both batches of specimens and single components with multiple test points. Designed for seamless integration with 6800 Series universal testing systems, the AT2 features standard bolt patterns for custom fixturing and accommodates a wide range of specimen geometries. Fully integrated with Bluehill® Universal software, it enables operators to quickly define and execute test sequences using grid, diamond, or custom layouts—boosting throughput, consistency, and testing efficiency.
-
Product
Portable Spectrophotometers
-
Hunter Associates Laboratory, Inc.
Measure on the go—including samples on plant production floors, in storage areas, shipping departments, or virtually anywhere that’s convenient. Our portable spectrophotometer are available in Directional 45°/0° and Diffuse d/8° geometries.
-
Product
NTSC Standard Pattern Generator
PG315N
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Correlation Analysis
-
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software.
-
Product
Straightness Measurement Kit
55283A
-
The Keysight 55283A Straightness Measurement Kit, used with the Keysight 5530 Laser Calibration System, makes straightness, squareness and parallelism measurements to identify geometry errors that seriously degrade machine tool performance. These measurements allow documentation, analysis and diagnosis of machine tool travel and parallel axes of motion.
-
Product
LED Test Production System
Lumere-LC
-
Evolusys Technologies Sdn. Bhd.
Lumere LC is a LED test and measurement system for various parameters of LED light. It is economical, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. Main application is in the production of LEDs.
-
Product
MPO/MTP Multi-Fiber Interferometer
-
Anfkom International Co.,Limited
It is an automatic and non contact fiber endface interferometer for both multi fiber and single fiber connectors. It can measure the geometry parameters of multi fiber connector such as fiber height,core dip, X and Y angel, radius of curvature with white light and measure geometry parameters of single fiber connector with red light. The software can display the surface of the connector in 3D image for a very short time, it need only 8s to test 12-core MT connector. It is intelligent , efficient,stable and accurate and very helpful in improving the quality of the product.
-
Product
Geometry
-
Our glass and coating geometry test instruments ensure fiber performance and adherence to telecom standards. Our solutions are capable of measuring diameter, circularity, and concentricity for both coatings and glass plus fiber curl. Our flexible geometry measurement systems not only work with standard telecom fibers, but are continually updated to meet new requirements, such as PM, multicore and hollow-core fibers.
-
Product
Artificial Skies
-
As a simulator maker, we can say the artificial sky, among other devices, is the ideal instrument for every lighting designer and lighting engineer. In fact, to predict daylight penetration inside a building, a scaled model under an artificial sky is the only reliable prediction method in the case of unusual situations, complex geometries, or heavily obstructed windows.
-
Product
Integrating Sphere Solutions
-
An integrating sphere is a light collector which takes advantage of physical geometry to homogenize any radiation being emitted inside by relying on a high-reflectance coating material. Depending on the wavelength range the end user using a sphere with, different coatings have different advantages based on the application.
-
Product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
-
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
Product
Standard Pattern Generator Board
BL-PG315-01
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Coordinate Measuring Machines
-
Coordinate Measuring Machines (CMMs) measure the geometry of physical objects by sensing points on the surface of the object with a touch probe. They are commonly used in manufacturing processes to inspect a physical part or assembly against the design specification.
-
Product
Fiber Test & Measurement
-
Thorlabs manufactures a range of devices for testing and measuring the performance of optical fiber. Power, spectral signature, polarization, or end face surface geometry can by characterized with out-of-the-box solutions from our catalog. EO modulators, optical switches, and light sources are available to treat light being used on a test bed.
-
Product
PAL Standard Pattern Generator
PG315P
-
The MicroImage PG315 pattern generator is designed for simple size and geometry reference applications. The PG315 will overlay one of five standard patterns including a centered cross line, a centered cross hair, a centered target style symbol, a dot grid (cross dot) array, a hatch grid (crosshatch) array.
-
Product
Quantum Efficiency Measurement Systems
-
Newest generation of quantum efficiency (yield) measurement tool, which allows the user to determine QE of powders, liquids, solids and films. An optically optimized geometry using an integration hemisphere and low stray light array spectrometer enables world class measurements and new applications.
