Defect
other than specified, imperfection .
-
Product
Contour Check Round & Edge
-
Laser measuring systems are of central importance for rolling mills to check the contours of steel profile for defects during the production process. A slight deformation on the surface of the profiles reduces the quality of the product, and in the worst case, a broken roll can even destroy the entire batch. With our systems Contour Check Round & Edge you identify and evaluate deviations at an early stage. Increase the process efficiency of your production - regardless of temperature and profile shape.
-
Product
Ultrasonic Testing
-
Device for detecting defects in finished products, semi-finished products and welded joints, as well as determining their coordinates and using DAC and DGS functios.
-
Product
E-beam Metrology And Inspection
-
Our HMI e-beam solutions help to locate and analyze individual chip defects amid millions of printed patterns.
-
Product
Infrared Microscope
DDR200/300 NIR
-
The McBain DDR200 NIR (for 200mm) and DDR300 NIR (for 300mm) provide high-speed defect detection and precision measurement on wafers and other parts. These cost-efficient systems offer unique advantages for both production and process development use, providing an optimum near-infrared (900-1700nm) solution when both subsurface defect detection and dimensional metrology are required.
-
Product
Network Emulator
KMAX
-
The KMAX network emulator helps network engineers test and measure performance in order to identify and remove defects. Network emulators turn well behaved development and test networks into the kind of slow, congested, and less-than-reliable services encountered on the internet. In addition, unlike the real internet, network emulators allow the operator to control these conditions so that products and apps can be subjected to controlled and repeatable tests, by routing selected packets through a series of impairment nodes.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Reject Station for X-Ray Image Analyser
IV-110I
-
IV-11OI is a reject station for X-Ray Image Analyser known for having an X-Ray Image Wire Defect Detection and a compact and space-saving dimension.
-
Product
Power Capacitor
POLB HD 7%
-
Lifasa - International Capacitors, SA
They are self-regenerating condensers with low loss polypropylene dielectric, filled with N2 inert gas mainly, or with resin, and with overpressure disconnection system, which offers a high level of safety against defects, when cutting the 3 phases in case of action.
-
Product
Ultrasonic Testing
Pundit 250 Array
-
The Pundit 250 Array brings a quantum leap in the ultrasonic pulse echo testing. A number of unique innovations make the Ultrasonic multi-channel instrument the best and fastest solution for thickness measurements, detecting defects and localizing objects which cannot be easily detected by any other technology. This includes the assessment of thick concrete elements such as tunnel linings as well as pipes and tendon ducts beyond the rebar layer.
-
Product
Software
Interface Analysis
-
Surface-mount components warp during the reflow process, and the area where they attach also changes shape during assembly. This interface between components is where solder, paste, and gaps created due to thermal expansion combine to create 100% good products, or defects such as Head-in-Pillow, Shorts, and Opens. Fully understanding that critical interface between surfaces is more important than ever.
-
Product
Vision Sensors
-
Companies in a wide range of industries rely on vision sensors to perform simple pass/fail, go/no go inspections that help ensure products and packaging are error-free and meet strict quality standards. Cognex In-Sight 2000 vision sensors provide easy and reliable inspections thanks to powerful vision tools, modular lighting and optics, and an easy-to-use setup environment. By reducing defects and increasing yield, Cognex vision sensors help manufacturers streamline their operations and increase profitability.
-
Product
Automated Control System for Veneer Edge Gluing Line
Vikat
-
The automated veneer splicing line control system is designed to identify defective veneer areas, control the scrap trimming, bonding of suitable areas and the formation of output sheets of a given size.
-
Product
Magnetic Particle Inspection
-
Is an inspection method used to identify defects on the surface of ferromagnetic materials by running a magnetic current through it.
-
Product
Precision Continuous Flow Metering + Dispense System
Graco Dispense Analyzer
-
A whole new level of precision for drivetrain gasketing. Detect air bubbles and defects you couldn't see before. Track critical measurements, including entrapped air. Quickly and easily find a defect's root cause. Avoid expensive problems by responding sooner. Save millions: Contain warranty claims and recalls. The Graco PCF and Analyzer combination: Your ultimate system for accurate, reliable dispensing. The new Graco Dispense Analyzer is a monitoring system capable of detecting the tiniest air bubble or error during adhesive dispensing. Paired with the Graco Precision Continuous Flow (PCF) system, the Analyzer monitors your dispense in real time, detecting immediately if conditions are off and may potentially compromise your final product. With the ability to respond immediately, you can avoid defects that lead to costly recalls. The Analyzer stores the signature of each dispense, giving you the ability to replay the data, even months or years after the actual dispense. Seeing the data replayed as if in real time, you can more easily pinpoint the root cause of the defect and contain a recall or warranty claim to only those products that were affected.
-
Product
EasySegment
-
Unsupervised mode: train only with “good” images to detect and segment anomalies and defects in new imagesSupervised mode: learn a model of the defects for better segmentation and detection precisionWorks with any image resolutionSupports data augmentation and masksCompatible with CPU and GPU processingIncludes the free Deep Learning Studio application for dataset creation, training and evaluationOnly available as part of the Deep Learning Bundle
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
Product
Torque Tester
TorqueLab® LTT-Series
-
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained.
-
Product
Surface Defect Inspection System
-
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
Product
Radiographic Inspection Test
-
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
-
Product
Hipot Tester
ET 2670 A
-
REOO ET 2670 A Solar Module Testing Machine is designed for PV module manufacturing inspection, enabling faster defect judgment and more stable quality verification during production. Built for solar factories, it supports reliable inspection flow.
-
Product
Vison Inspection System
-
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
Product
VisualDetect basic
VDb-01
-
Hachmann Innovative Elektronik
VisualDetect basic is an easily operated voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces, whereas a dot matrix display shows the measured current [I/A] or frequency [f/Hz]. Thanks to the integrated configuration menu it can be adjusted to switchgears operated below nominal voltage on-site.
-
Product
MASK DR-SEM
-
Our defect review SEM tools perform detailed reviews of minute defects on photomasks.
-
Product
Wafer Internal Inspection System
INSPECTRA® IR Series
-
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
Product
3D Sensors (Main Screen)
surfaceCONTROL
-
surfaceCONTROL sensors are used for 3D measurements and surface inspections. The sensors use the fringe projection principle to detect diffuse reflecting surface and to generate a 3D point cloud. This point cloud is subsequently evaluated in order to recognize geometry, extremely small defects and discontinuities on the surface. Sensors with different measurement areas are available. This enables the inspection of the finest of structures on components as well as shape deviations on large-area attachments. Powerful software packages are available for evaluation and parameter setting.
-
Product
Destructive Physical Analysis (DPA)
-
Is the process of disassembling, testing, and inspecting a component for the purpose of determining conformance with applicable design and process requirements. This process of sample testing is used to ensure that a high reliability component or device is fabricated to the required standards. Destructive Physical Analysis is also used effectively to discover process defects for troublesome production lot problems.
-
Product
Ultrasonic Imaging System
USPC 3010
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Detects internal defects in new materials and metals. The wide frequency range up to 35 MHz enables highestresolution. A-, C-, and D-scans can be recorded. The imaging in B-scans is an option.
-
Product
Welding Resistance Tester
WRT
-
The Welding Resistance Tester is used in battery assembly lines to detect defective intercell connections. It is equipped with a 5-channel test head for car and truck batteries. It features 1-20 O DC resistance ranges and a multi-line LC display for OCV, CCV, and DCR measurements for 5 intercell connections.
-
Product
Magnetic Permeability Meter Ferromaster
-
Instrument for easy measurement of the relative magnetic permeability µr of feebly magnetic materials and workpieces with a permeability between 1.001 and 1.999. The permeability is measured by touching the workpiece with the probe tip and reading the result from the display. Typical applications are: non-destructive testing of materials, e. g. quality control of stainless steel, material selection for electron-/ion-beam equipment, detection of material defects induced by mechanical or thermal stress.
-
Product
In-Line X-ray Inspection System
X-eye 6200
-
Automatically in-line inspect Solder joint defects of PCBA, and other defects on Hidden Components.Able to judge Good/NG fast with inspection speed of 1sec/FOV and the program can set ROIs conveniently.Performing X-ray inspection in various production site, integrated with other manufacturing equipements.
