Coarse Wavelength Division Multiplexing
-
Product
PXI High Density MUX BRIC, 16-Chan, 10-Pole
40-570-411
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-785C-552
Multiplexer Module
The 40-785C-552 (PXI) and 42-785C-552 (PXIe) are dual failsafe SP6T 50 GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI Dual 3-Channel 10A Solid State MUX
40-666-011
Multiplexer Module
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 26.5GHz SMA
60-802-308
Multiplexer Module
The 60-802-308 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 14-Bank 6GHz SMA
60-802-014
Multiplexer Module
The 60-802-014 is a 4-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 5-Bank, 50GHz, 50Ω, SMA-2.4
60-800-605
Microwave Multiplexer
Our 60-800-605 is a 5 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI High Voltage Switching - 5-Bank, 1-Pole, 8:1 Multiplexer Plugin Module
65-231-908
Multiplexer Module
The 65-231-908 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 5-Bank 26.5GHz SMA
60-801-305
Multiplexer Module
The 60-801-305 is a 6-channel, 5-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67GHz, 50Ω, SMA-1.85
40-785C-472
Multiplexer Module
The 40-785C-472 (PXI) and 42-785C-472 (PXIe) are dual SP4T 67GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-218-M62.5-HI
Multiplexer Module
The 40/42-852A-218-M62.5-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 10A Power Multiplexer, 8-Bank, 4-Channel (SP4T)
40-661A-001
Multiplexer Module
The 40-661A-001 is a single pole, 8-bank, 4-channel (SP4T) PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
-
Product
PXI Versatile Multiplexer, Solid State, 125mA, 100V
40-683A-001
Multiplexer Module
The 40-683A-001 is a very high-density versatile PXI Multiplexer module featuring a wide range of selectable switching configurations with 125mA current and 100V voltage handling. The 40-683A is especially useful where a high-density MUX array is required that can adapt to different test configurations for different test targets, or where a test system may have to be reconfigured in the future.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 22 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-131-TE
Multiplexer Module
The 40-788-131-TE (PXI) and 42-788-131-TE (PXIe) are single failsafe SP10T 22 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 67GHz, 50Ω, SMA-1.85
40-785C-572
Multiplexer Module
The 40-785C-572 (PXI) and 42-785C-572 (PXIe) are dual SP6T 67GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, SP6T, 10-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-710
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
LXI Microwave Multiplexer, SP4T, 3-Bank, 67GHz, 50Ω, SMA-1.85
60-803-803
Multiplexer Module
Our 60-803-804 is a 4 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe Very High Density Multiplexer, 10-Channel, 16-Pole
40-675B-002-10/16
Multiplexer Module
The 40-675B-002-10/16 (PXI) and the 42-675B-002-10/16 (PXIe) are 10-channel, 16-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI High Density Screened Mux 49 Ch 2 Pole
40-670A-021-S-49/2
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected.In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 12-Channel, 1-Pole
42-514-107
Multiplexer Module
The 40-514-107 (PXI) and 42-514-107 (PXIe) are low density multiplexers in dual 12-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP12T, 18 GHz, 50 Ω, SMA, Failsafe
42-788-221
Multiplexer Module
The 40-788-221 (PXI) and 42-788-221 (PXIe) are single failsafe SP12T 18 GHz unterminated microwave multiplexers. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Failsafe
40-785C-571-T
Multiplexer Module
The 40-785C-571-T (PXI) and 42-785C-571-T (PXIe) are single failsafe SP6T 67 GHz with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 10-Bank 18GHz SMA
60-802-210
Multiplexer Module
The 60-802-210 is a 4-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 6-Bank 6GHz SMA
60-801-006
Multiplexer Module
The 60-801-006 is a 6-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI 20 Banks of 8 Channel 1 Pole MUX
40-615-022-20/8/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI 2 Amp MUX, Quad 8-Channel 2-Pole
40-635-009
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI Remote Mount Single SP6T Multiplexer 26.5GHz 50, SMA-2.9
40-785B-531-E
Multiplexer Module
The 40-785B-531-E is a remote mount single 6-channel 26.5GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXIe-2790, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module
782576-01
Multiplexer Module
PXIe, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module—The PXIe‑2790 can either switch or combine RF signals for multi-DUT cellular and wireless connectivity production test. It features high-performance solid-state relays that offer unique benefits such as an unlimited mechanical lifetime and fast switching time, as well as front-mounted SMA connectors that provide easy connection to your RF devices.
-
Product
LXI Microwave Multiplexer, SP4T, 13-Bank, 67GHz, 50Ω, SMA-1.85
60-803-813
Multiplexer Module
Our 60-803-813 is a 13 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9, Remote Mount
40-785C-443-E
Multiplexer Module
The 40-785C-443-E (PXI) and 42-785C-443-E (PXIe) are triple SP4T 40GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
