Barometric Pressure
See Also: Pitot Static Testers
-
Product
Barometric Pressure Transmitter
T2214
-
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
Product
Barometric Pressure Sensors
-
Barometric pressure sensors measure fluctuations in the pressure exerted by the atmosphere. The sensors require protection from condensing humidity, precipitation, and water ingress. They are typically housed with the datalogger inside an environmental enclosure. If the enclosure is airtight, the sensor's pressure port must be vented to the atmosphere.
-
Product
Barometric Pressure Transmitter
T2414
-
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
Product
Barometric Pressure Sensors
-
Accurate within 1.5 % across a pressure range of 15 to 115 kPa (4.43 to 34.96 in Hg). Long-term non-stability has been measured continuously indoors and in natural conditions (with sensors mounted inside a datalogger enclosure) for multiple sensors and is less than 0.5 % per year. Temperature effects on signal are less than 1 % across a wide temperature range (-20 to 50 C).
-
Product
Barometric Pressure Transmitter
T2314
-
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
Product
Barometric Pressure Transmitter
-
Comptus Barometric pressure sensors utilize an integrated silicon, absolute pressure sensor with internal temperature compensation. The sensor is mounted to the signal conditioner board. A 3/16 inch diameter tube may be attached to the sensor to provide remote pressure sensing. The output of the sensor is scaled to provide the desired output signal.
-
Product
Anemometer Logger Sensor
NUL-242
-
The NeuLog anemometer sensor enables measurements ofwind velocity. Combined with temperature, relative humidity,dew point and barometric pressure sensors, it can be used tomake very interesting weather measurements.
-
Product
Explosive Atmosphere Test
-
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
Product
Online Dissolved Oxygen Controller
LD-LODC-A10
-
Online Dissolved Oxygen ControllerLD-LODC-A10features 1 to 2 points dissolved oxygen calibration system, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. It measures the amount of dissolved oxygen in mg/l, ppm units or in % of saturation. The accuracy of measurement is improved by manual salinity and barometric pressure compensation mode.
-
Product
Wireless Transmitters
-
Omega wireless transmitters are weather-resistant and are designed to deliver a wide range of data such as voltage, current, temperature, humidity, barometric pressure, and pH.
-
Product
3-Axis Ultrasonic Anemometer
HD2003
-
HD2003 is a 3-axis static anemometer for measuring wind speed and direction, U-V-W cartesian components of speed, wind gust, sound speed, sonic temperature, air temperature, relative humidity and barometric pressure.
-
Product
SparkFun Environmental Sensor Breakout
BME680 (Qwiic)
-
The SparkFun BME680 Environmental Sensor is a breakout that combines a gas sensor with temperature, humidity and barometric pressure sensing for a complete environmental sensor in a single package. The gas sensor on the BME680 can detect a wide variety of volatile organic compounds (or VOC for short) to monitor indoor air quality. Combine that with precise temperature, humidity, and barometric pressure and the BME680 can work as a completely standalone environmental sensor all in a 1in. x 1in. breakout!
-
Product
Humidity Detectors
-
A humidity detector, also referred to as a humidity meter or humidity gauge, is a device with a humidity sensor that measures the relative humidity in the air. PCE Instruments offers a number of humidity detector products including handheld humidity detector, data recording or data logging humidity detector, and combination or multifunction humidity detector devices that also measure parameters such as room or ambient temperature and atmospheric or barometric pressure. A humidity detector can measure relative humidity (RH) as a percentage (%) from 0 to 100 % RH, depending on the humidity measurement range of the specific model.Humidity is a key factor in everything from library and museum archival to agriculture, construction, manufacturing, transportation, warehousing, and heating, ventilation, air conditioning and refrigeration (HVACR). A relative humidity meter also is helpful in evaluating workers' heat stress risk on production floors and job sites. In addition, humidity plays an important role in the residential sector. If the humidity is too high in a private household, mold can grow. Mold creates a health hazard for anyone breathing the air in the home.
-
Product
SparkFun Atmospheric Sensor Breakout
BME280 (Qwiic)
-
The SparkFun BME280 Atmospheric Sensor Breakout is an easy way to measure barometric pressure, humidity, and temperature readings, all without taking up too much space. Basically, you can find out anything you need to know about atmospheric conditions from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
PocketLab Air
-
PocketLab Air is an all-in-one science lab for investigating climate change and air pollution in your environment. PocketLab Air can measure carbon dioxide, ozone, particulate matter, temperature, humidity, barometric pressure, and light. We've designed PocketLab Air to be capable enough for climate and air quality researchers but simple enough for a 4th grade student learning about Earth science.
-
Product
SparkFun Atmospheric Sensor Breakout
BME280
-
The SparkFun BME280 Atmospheric Sensor Breakout is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been design to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
-
Product
Barometric Pressure/Temperature/Altitude Sensor
BMP180
-
This precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes with altitude you can also use it as an altimeter! The sensor is soldered onto a PCB with a 3.3V regulator, I2C level shifter and pull-up resistors on the I2C pins.
-
Product
PITOT STATIC TESTER
ADSE 745
-
The ADSE 745 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wing. The multi-pressure outlets option can suit the more complex pilot-static-systems. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.
-
Product
Pitot Static Tester
ADSE 650
-
The ADSE 650 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fix and rotary wings. This Pitot Static Tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The large touch screen display, with on-screen help ,enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.
-
Product
Weather Stations
-
We have range of options when it comes to weather stations. From a basic system for monitoring wind speed right up to a comprehensive set of sensors covering wind, temperature, barometric pressure, humidity, rainfall, solar radiation etc.
-
Product
Pitot Static Tester
ADSE 643
-
The ADSE 643 caters fully for all aircraft types and the different electrical power supplies.It can be used for testing high performance civil and military aircraft, fixed and rotary wing.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems.The ease of use and portability enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator.The test set is housed in an anodized metal and rugged case.An attached case contains the pressure hoses and electrical cables.
-
Product
Professional Weather Station
E9250
-
• Measures temperature, rainfall, barometric pressure and wind speed• Wireless technology allows outdoor unit to communicate with indoor display• Easy to use display panel with programmable functions• Works with external sensors for even more functionality.
-
Product
Multi-Sense Humidity Probe
HP125 Series
-
The HP125 Multi-Sense Humidity Probe is a cost effective, easy to use solution to many industrial and laboratory measurement and control applications. The HP125 probe exploits the latest advancements in polymer humidity sensing technology and compact electronic circuitry. It is designed to continuously measure up to 4 measurement parameters using a single intelligent sensor tip including RH%, calculated Dew Point, Temperature and either Absolute Pressure or Barometric Pressure!
-
Product
Motor Octane Testing
DewTrak II MO
-
DewTrakII MO dew point/humidity transmitter is an optical chill mirror hygrometer designed to continuously measure the moisture content and Barometric pressure in the motor octane testing process. It is used to monitor and ensure compliance with test
-
Product
Multi-Sensor
Panda
-
The NeuLog Panda multi-sensor can be used for any science experiment which utilizes Room Temperature, Light, Barometric pressure, Altitude, Sound, Relative Humidity, Dew-Point, Magnetic Field and G-Acceleration readings.Panda is used for environmental data collection and other experiments in Natural Science, Biology, Physics and Chemistry. It is specially designed for primary school level.The multi-sensor comes pre-calibrated so you can start experimentation right out of the box
-
Product
Dew Point Logger Sensor
NUL-245
-
This sensor measures temperature and humidity in a volume and gives the temperature below which the water vapor in that volume of air (at a constant barometric pressure) condenses into liquid water (the dew point).
-
Product
Ambient Air Quality Monitoring System
AQMS
-
AQMS, the doctor for "Human Health"An Air Quality Monitoring Station (AQMS) is a system that measures metrological parameters such as wind speed, wind direction, rainfall, radiation, temperature, barometric pressure and ambient parameters. The AQMS also integrates a series of ambient analyzers to monitor the concentration of air pollutants (such as SO2, NOx, CO, O3, THC, PM, etc.), continuously. HORIBA also provides mobile monitoring stations that can be used to monitor ambient conditions at multiple sites.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
T, RH, Pressure and Air Speed Transmitters
HD2001… Series
-
Relative Humidity, temperature, barometric pressure, air speed trasmitters with display
-
Product
SparkFun Atmospheric Sensor Breakout
BME280 (with Headers)
-
The SparkFun BME280 Atmospheric Sensor Breakout with Headers is the easy way to measure barometric pressure, humidity, and temperature readings all without taking up too much space. Basically, anything you need to know about atmospheric conditions you can find out from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring.
