Earth Resistance Testers
See Also: Earth Testers, Ground Resistance Testers
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Earth resistance meters
-
The PROMAX earth meters guarantee the proper operation of industrial and home electrical circuits.
-
Product
Non-Trip Earth Resistance Measurement
M73
-
M73 has been developed for operators who mainly work on private installations. M73 is very easy to use, it is very small in size and it carries out all necessary tests to establish COMPLIANCE (and hence ensure SAFETY) of an electric system.
-
Product
Earth Resistance & Resistivity Meter
MRU-200
-
MRU-200 is the only meter in the market which uses all measurement methods.Possible measurements:- earth resistance measurment with 2-pole, 3-pole,4-pole method,- impulse earth resistance measurement, two kinds of measuring impulse 4/10s, 10/350s,- earth resistance measurement without disconnecting measured earths (using clamp),
-
Product
Earth Resistance & Resistivity Meter (for 50Hz mains)
MRU-120
-
* earth resistance measurment with 3-pole,4-pole method, * earth resistance measurement without disconnecting measured earths (using clamp), * continuity of equipotential bondings and protecting conductors * two clamps earth resistance measurement without auxiliary test probs, * earth resistivity measurement,
-
Product
DC Resistance Tester
DCSS502BC
-
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
Product
Earth Tester
TAURUS PRECIOHM ET
-
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Product
Megohmmeters/Insulation Resistance Testers
-
Full line of megohmmeters with test voltages 50V to 5000V. Capability to measure insulation resistance up to 10T. These rugged, weather resistant meters are accurate, reliable and built to perform. Battery, AC Powered & Hand-cranked models available.
-
Product
Contact Resistance Tester
JYL
-
As a high current passes through a pair of mechanically independent metallic contacts, the contact resistance must be as low as possible. Increasing the contact resistance of the contact often causes a large voltage drop on the contact, which reduces the input power of the load equipment. If the contact resistance of one or two contacts becomes large, the three-phase voltage of the load equipment will be unbalanced, causing phase loss operation.
-
Product
Resistive Current Tester
-
Weshine Electric Manufacturing Co., Ltd
Long Distance Digital Zinc Oxide Arrester Resistive Current Safety Testing Set
-
Product
Portable Winding Resistance Tester
-
1. Handheld winding resistance meter2. Conversion function for standard temperature resistance.3. 500 test data can be saved and download by flash disk.4. Temperature testing function.
-
Product
Earth Ground Resistance Meter
1623-2
-
The Fluke 1623-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1623-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps.
-
Product
Neutral Earthing
International Standards
-
NERs may only be called upon to operate a few times in their service life, which may be 25 years or more. Reliability is imperative, and has been proved over many years in electric traction rolling stock and under conditions of severe vibration and extreme climate world-wide.
-
-
Product
Sole Puncture Resistant Tester
UI-FT03-1
-
Sole Puncture Resistant Tester is to test safety shoe sole steel plate insert nail puncture resistance/penetration ability.
-
Product
Contact Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Surface Insulation Resistivity Tester
Model SRT1
-
The model SRT1 is an advanced instrument for measuring surface insulation resistivity following ASTM standard A717 (IEC 404-11). Featuring the improved, patented Allegheny Ludlum Head*, which providesincreased reliability and repeatability while decreasing maintenance costs. Its floating baseplate assures button alignment across the full sample width and length.
-
Product
Earth Leakage
-
National Meter Industries Inc.
This new range features a series of improvements intended in particular for installing unitson switchboards. Along with the usual attachment elements, this unit can be installed onDIN rails using an accessory, which facilitates its installation.
-
Product
DIGITAL EARTH TESTER
MTD-20KWe
-
The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.
-
Product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
-
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
Product
Shoe Heat Resistance Tester
UI-FT28
-
Shoe Heat Resistance Tester is to test shoe outsole and upper hot contact resistance ability especially for safety shoe. Heat Resistance Test Method includes ISO 20344, SATRA TM49, EN 344 and etc.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
PE/ Ground, Insulation Resistance Tester
Handheld
-
The safety testers of the Handheld class are used to measure PE/ Ground resistances, insulation resistances and to perform a simple functional test. The small and sturdy universal testers are intended for standard-compliant safety tests in workshops and production as well as for mobile operation during repair, installation, service and more.
-
Product
Winding Resistance Tester
JYR-50C/40C/20C
-
1. With demagnetization function.2. Testing range reach to 20k3. Also apply to testing tranformer with high winding resistance.
-
Product
Large Range Resistivity Tester
HS-SFRT
-
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
