Temperature Transmitters
Convey temperatures to a remote receiver.
-
Product
Force Transmitter
LKVE/i
-
The PIAB LKVE electronic overload protection system consists of a force transmitter with amplifier and an electronic signal processing unit. The PIAB LKVE force transmitter is attached to a stationary line part. The rope is deflected via a slight angle between the two wheels and the clamping jaw. When loaded, the rope tends to straighten and applies a force which is transmitted to the load cell. The load cell in the PIAB LKVE delivers a signal proportional to the force on the load cell. The signal is amplified and is converted to 4-20mA. This standardized signal (4-20mA) allows distances between the force transmitter and the electronic unit to be 500 m.
-
Product
Pressure Transmitter
PS2
-
- Digital temperature compensation and nonlinear correction- High sensitivity, high precision, high stability- Full temperature compensation, good electrical performance and long-term stability- The plug and shell are integrally spin-stable, stable and waterproof, to avoid loosening the thread of ordinary plug- A variety of signal outputs, convert the pressure of the measured medium into 4~20mA,0~10VDC analog signals, RS485 digital signals- With RS485 communication interface, the monitoring system can easily read the measured value- The shell adopts laser welding, high reliability, long life, long-term stability and reliability
-
Product
Level Transmitters
-
NOSHOK industrial submersible level transmitters are designed to withstand harsh applications. Our offering includes a small diameter (0.97") submersible level transmitter designed for hydrostatic level measurement for use in applications including bore holes and wells with small diameters. This sensor provides low power output signals for battery-powered applications, and an optional temperature output available. We also provide a cage-protected level transmitter ideal for harsh environments including sludge, slurries, tank monitoring, water & wastewater.
-
Product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
782975-01
Temperature Input Module
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
-
-
Product
Rainfall Transmitter
-
Model A70 Rainfall Transmitter converts the signal from a tipping bucket rain gauge into a 4-20 mA signal for input to a computer, meters, system controls or other instrumentation. It features reliability, low cost, accuracy, simplicity of operation and ruggedness.
-
Product
Belt-Pack Transmitter
LMb
-
The LMb transmitter can be configured to operate as a "one touch" device with a single power on/off switch on the top panel, or with full access to all operational parameters using the side panel membrane switches and LCD interface. The top panel switch can also be configured to provide a mute or talkback function.
-
Product
Wireless Transmitters
-
Omega wireless transmitters are weather-resistant and are designed to deliver a wide range of data such as voltage, current, temperature, humidity, barometric pressure, and pH.
-
Product
Wind Transmitters
-
Comptus wind speed and direction transmitters convert the sensor signals into electrical outputs suitable for connection to displays, computers, dataloggers, wireless transmitters, or other controls. Output options include: 0-1 mA, 0-1 V, 0--5 V or 4-20 mA. Power options include: 24 VAC, 120VAC, 230VAC, 12-24 VDC. Comptus transmitters come standard in a track mount for installation in existing enclosures. They are also available in NEMA rated enclosures. Please contact us for enclosure options.
-
Product
Standard Transmitter
Tipix 3000
-
The TIPIX 3000 is a transmitter purposely designed for deep Induced Polarisation or Resistivity sounding investigations. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers.
-
Product
Optical Transmitter
ST1013-10mW
-
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home)Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices *Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
Product
Satellite Optical Transmitter
SST-15CW
-
Hangzhou Softel Optic Co., Ltd.
* Designed for satellite optical system*Wide operating frequency range: 47-2150MHz*Excellent linearity and flatness*Using 1-core single-mode fiber, high return loss*Build-in CWDM, using DFB coaxial small package laser*Output 13/18V, 0/22KHz to LNB working*ALNB mode switch offers the possibility to use either Quattro or QUAD LNB*A distribution of up to 16 optical nodes is possible*Red-LED for power indication*Smaller size and easier installation
-
Product
Mission Data Transmitters
-
L3 Cincinnati Electronics (L3 CE) offers a wide choice of modulators and transmitters for spacecraft ranging from X-Band to Ku-Band. All the products listed below can be customized to specific user requirements.
-
Product
Temperature and Humidity Transmitter
T3319-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
5-Watt Broadband Transmitter
Loc3 5W
-
The 5-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
785186-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Temperature Thermowells, Sensors & Transmitters
-
Rosemount temperature products have been recognized for leadership in the process industry. As your trusted temperature partner, Emerson delivers factory-tested, ready-to-install temperature assemblies. With our industry leading portfolio of transmitters, sensors and thermowells, we provide reliable solutions for your temperature applications.
-
Product
Regulated Transmitter
TIP One
-
The TIP One is purposely designed for shallow induced polarisation or Resistivity sounding investigations. The TIP One injects a regulated current or regulated voltage into the ground via a simple 12V battery.
-
Product
Temperature Measurement
K- TC16
-
The K-TC modules belong to the Influx K-series instrumentation range for CAN applications. The stackable K-TC is an ideal for those applications that require a large number of thermocouples for example vehicle durability, winter and summer testing.
-
Product
Temperature Measurement
-
With over 125 years of experience in temperature measurement, we have the technology and application knowledge for even the most difficult environments and hazardous areas.
-
Product
Humidity and Temperature
Humidity of Building Materials
-
The T660 is a professional hand-held instrument for fast, non-destructive determination of moisture content distributions in areas up to a depth of 4 cm from the surface. The T610 is a professional hand-held instrument for rapid non-destructive measurement of sub-surface moisture content.By means of microwave technology it is possible to detect distributions of moisture content at a depth of up to 300 mm.
-
Product
Humidity transmitters for HVAC
-
Humidity transmitter for heating, ventilation and air conditioning technology. Humidity transmitters for building technology are also available as OEM versions in custom designs.
-
Product
CO2 Concentration Transmitter
H5421
-
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
Product
Temperature Calibration
-
In our temperature lab we have the capability calibrate a wide range of temperature products such as catering food probes from deli to restaurant, industrial systems for manufacturing and quality checks using thermocouples surface probes or insertion probes we also calibrate IR (Infrared) thermometers.
-
Product
Dual Temperature
-
The Fieldpiece Dual-Temperature Accessory, model ATH4, measures two temperatures simultaneously using the included k-type, wrap tab beaded thermocouples. The technology inside the ATH4 provides superior temperature compensation in rapidly changing environments commonly found while performing field service. Use the ATH4 to find Delta T and just about any temperature split you want to measure. Displays T1, T2 and T1-T2 on your Fieldpiece meter, handle or data logger. It is included with the HVAC Guide® System Analyzer to get target superheat and for the Target Evaporator Exit Temperature test. Fieldpiece offers a wide variety of k-type thermocouples for various HVAC specific applications. Use pipe clamp T/Cs with the ATH4 to check for blocked filters.
-
Product
Temperature Logger
TRIL-8
-
The LogTag® Dry Ice “Probe-less” Temperature Logger operates, measures and stores up to 8000 temperature readings in temperature environments ranging from -80°C to +40°C (-112°F to +104°F).
-
Product
Temperature Controllers
-
Panasonic Industrial Devices Sales Company of America
Panasonic's line of versatile Temperature Controllers are offered in a wide selection of inputs and outputs, including PID (built-in auto-tuning function included), analog signal conditioners with scaling, and panel meters with a very bright and easy to read display. The KT line of controllers (pictured) is well suited for a wide variety of machine and process control applications.
-
Product
Power Transmitter
ITL-101
-
Power Transmitters measure precise power of any waveform generated by electronic circuits. The ITL-101 cannot only be used for stationary power measurements, but also for power control on machines using fast response option and bi-polar output option. For frequency inverter applications minimal use of energy is and issue and here the ITL-101 finds its place.
-
Product
Temperature Sensors
-
Universal temperature measurement for liquids and gasesWith its product portfolio of screw-in and insertion thermometers as well as temperature switches SICK offers high-quality solutions for contact temperature measurement in liquids and gases. The devices can optimally be adapted to meet individual requirements through its various insertion lengths and the flexible mechanical configuration possibilities.
-
Product
CO2 Concentration Transmitter
T5341
-
The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
