Shock wave
short moment intense amplitude faster than sound wave
See Also: Wave, Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave
-
Product
High-acceleration Shock Tester
DP-1200-18
-
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Product
Pressure Sensors For Blast Testing
-
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
Product
The Nanomotor®
-
The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Hydraulic Vertical Shock Test System
KRD10 series
-
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
-
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
Product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
-
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
Product
Acoustic Scoring System
AcoustiScore
-
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
Product
Millimeter Wave Amplifiers
-
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
Product
Shock And Vibration Testing
-
Alpes Lasers SA offers a service of shock and vibration testing. Originally designed for qualifying laser devices to the MIL-STD-810H defense standard, the same tests can be applied to a variety of different products.
-
Product
Thermal Shock Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Three zone thermal shock chamber uses the test material structure or composite material to withstand the degree of extreme high temperature and low temperature in a continuous environment in an instant, so as to test the chemical changes or physical damage caused by thermal expansion and contraction in the shortest time.
-
Product
Thermal Shock Chambers
VTS-Series
-
Vertical Thermal Shock chambers consist of two separately controlled hot and cold zones. Product is transferred between these zones for rapid product temperature changes. Thermal Shock Chambers are designed to perform tailored environmental stress screening of component and board level electronic assemblies. The return on investment in both actual savings and customer confidence adds greatly to the value of electronic assemblies screened in a CSZ thermal shock system.
-
Product
Wave Quality Analyzer
Nexus 1500
-
From the Industrial Giants, Fortune 100 companies to municipal utilities, an energy management and power monitoring program is critical to their success. The Nexus® 1500, the most advanced monitoring product, provides the global picture of power quality and usage from any metered point within a distribution network, enabling users to make power-related decisions quickly and effectively.
-
Product
Millimeter Wave Antennas
-
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
Product
Mechanical Shock Testing
-
Classical • Half-sine • Sawtooth • Shock Synthesis • Sustained Presure Shock Response Spectrum (SRS) • Transient Shock Response
-
Product
Vertical Thermal Shock Chambers
FSV Series
-
Bemco FSV Series Vertical Thermal Shock chambers are available in two zone (FS2V - hot and cold) and three zone (FS3V hot - cold - hot) versions, with two temperature ranges (-75 C to +200 C or -160 C to +200 C), and two types of cooling systems (all mechanical cooling - no expendable refrigerant required, or all LN2). Very low temperature, -160 C chambers, are always liquid nitrogen cooled. Two zone chambers are offered in four standard sizes, while three zone chambers are offered in three standard sizes.
-
Product
Mm Wave Measurement
Erickson PM5B
-
bsw TestSystems & Consulting AG
Erickson PM5B from VDI, which has been further optimised in the version just presented. The measuring head of the PM5B operates in the WR10 band, i.e. in the 75 - 110 GHz range. High-precision accessories, so-called tapers, provide for adjustments and thus make measurements in the waveguide bands, currently up to WR0.34 beyond 3 THz, possible.
-
-
Product
Pressure Based Waves
5218
-
Measure pressure based Waves with the Aanderaa Wave Sensors- compact fully integrated sensors for measuring wave and tide conditionsThe 5218 wave sensor is designed to be mounted on the Aanderaa SeaGuard top-end plate or connected to SmartGuard using AiCaP CANbus or in other measurement systems using the RS-232 interface.The 5218R wave sensor sensor is designed for use with long cables by means of RS-422 full duplex interface.Both wave sensors are based on a silicon piezoresistive pressure sensor. The pressure measurements are sampled and temperature compensated by an advanced Digital Signal Processor.The wave sensor application areas are in fixed installations, either deployed in a seabed installation in shallow waters, or mounted onto a fixed structure in the upper water column.
-
Product
Guided Wave Radar Sensors
LVRD10 Series
-
The LVRD10 Series guided wave radar transmitters provide continuous level measurement with a 4 to 20 mA signal output. Offered in single rod, coaxial, or weight & cable probes in 3 or 6 foot lengths
-
Product
Shock Test Systems
-
Accurately measure the fragility of products and evaluate how they respond to specific shock inputs.
-
Product
Ring Wave Generator
SKS-1206IA/SKS-1206IB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The ring wave generator is fully compliant with the new standards of IEC61000-4-12 and GB/T17626.12. The interface contains standard differences between IEC and Chinese national standards. Users can choose to enter the corresponding interface to perform different Test: Program -controlled high-voltage power supply and electronic switch have the characteristics of high precision, long life and good reproducibility.
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
Wave Quality Analyzer
APQM-707
-
This equipment is a power quality analyzer according to the European standard EN 50160. The Amperis APQM-707 is a high-tech product that allows universal measurement of the parameters of 50/60 Hz electrical networks, as well as the analysis and recording of these parameters.
-
Product
Digital Classical Shock Controller
DVC-4/8 Shock
-
The CSC- I will perform all of the 'classical' shock tests as defined in MIL-STD-810 and is equally useful for environmental qual testing or production test screening. Automatic calculation of pre- and post-pulse compensation assures the maximum performance from your test system.
-
Product
Thermal Shock Chamber
ATS Series
-
Thermotron thermal shock chambers meet a variety of testing needs and come in three configurations: vertical, horizontal, and double duty. A product transfer mechanism automatically transfers products under test from hot to cold zones and back when programmed in the controller.
-
Product
Shock Response Spectrum Analysis
-
A Shock Response Spectrum (SRS) is a graphical presentation of a transient acceleration pulse’s potential to damage a structure. It plots the peak acceleration responses of a bank of single degree-of-freedom (SDOF) spring, mass damper systems all experiencing the same base-excitation as if on a rigid massless base. Each SDOF system has a different natural frequency; they all have the same viscous damping factor.
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
Thermal Shock Chambers
-
Specialized environmental test devices that rapidly move products between extreme hot and cold temperatures to simulate real-world stress.
-
Product
Liquid Thermal Shock Baths
TSB Series
-
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
