-
Product
3U CompactPCI Serial Blades
-
The PICMG CPCI-S.0 CompactPCI Serial standard, which evolved from the PICMG 2.0 specification, is the fastest, most versatile, most cost-effective open standard for CompactPCI (CPCI). The Serial standard is mechanically and electronically compatible with 3U and 6U euro-cards, defining an interface for high-speed switched fabrics with a star topology. Point-to-point connectors allow up to eight peripherals on one system slot without switches or bridges. Ethernet data transfer can be configured with full mesh topology, which allows up to 1000Base-T connections to all peripheral slots for redundant, safety-critical systems.
-
Product
AdvancedTCA Backplanes
-
Mesh, Dual Star (5U), and 7U Pluggable Dual Star. Versions for both 19" rackmount and 23" ETSI racks are available. All Elma Electronic AdvancedTCA backplanes are compliant to the PICMG 3.0 Rev. 1.0 specifications.
-
Product
8-Slot 64-Bit 6U CompactPCI Backplane
cBP-6408R
-
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- Design for 64-bit/33MHz CompactPCI computer system application- One system slot with seven expansion slots, system on right hand side
-
Product
COM-HPC Client Type Reference Carrier Board in ATX Form Factor
COM-HPC Client Base
-
The COM-HPC Client Base is an ATX size COM-HPC Client Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Client Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
CTEL 6U 16 slot left justfied, P1-2s, P3-5l
103CTEL616-7146
-
CompactPCI CTEL 6U 16 slot with system slot left, H110 bus, fully compliant to the PICMG basic specification 2.0 R3.0, Hot Swap specification 2.1 R1, andv PICMG H.110 Computer Telephony specification 2.5 R1.0.
-
Product
PICMG 2.16 Type 12H Rackmount - 12U
12H21FDXC8Y4VQFX
-
High quality 19" rackmount chassis platform consisting of pre-galvanized steel enclosures, PICMIG 2.16 or 2.17 backplane, power supply, redundant push/pull cooling system and AC/DC power components. Assembled, wired and tested prior to shipment.
-
Product
3U cPCI Serial Power Backplanes
-
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
Product
3U CompactPCI® Single 64-bit PMC Slot Carrier Board
cPCI-8301
-
- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- Supports one single-size 32,64-bit/33,66 MHz PMC site in 4HP width- Universal V(I/O) decided by backplane- Comprehensive EMC shielding
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
Product
2 Slot 1U CompactPCI 19" Rackmount Development Platform; Type 39 19" Rackmount Chassis
39C02AD118Y3HCBX
-
The Type 39C, 1U is an advanced generation of CompactPCI chassis for PICMG 2.0, 2.16, 2.17, and EXP.0 applications. IEEE 1101.10/11, 6U x 160mm CPCI cards from the front and 6U x 80mm I/O cards from the rear.
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
-
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
6U Compact PCI® Single Board Computer
CP62007N
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007N is a 6U CompactPCI® single board computer designed by LinkedHope® based on Intel® QM87 chipset. The compact and space-saving processor board meets the PICMG® CompactPCI® specifications. There are SATAIII, USB3.0, Gigabit Ethernet, and Keyboard/Mouse interfaces on the board. CP62007N supports 64GB SSD, facilitating the operating system installing.Part of CP62007N’s rear I/O uses high speed ZD connectors for transferring PCIe2.0, USB3.0, SATAIII and other high speed signals, leading to 2x 8 PCIe (to J3-J4) and a 1x 8 PCIe to XMC. All the PCIe is flexible configuration, for instance, a 2x 8 PCIe can be set into 2 x8, 1 x8 + 2 x4, or 4 x4.
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
-
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
8 Slot CP, 9UM, 3xP47, Type 39 CP 4U 84T
39C08ADX48Y3HQBX
-
The Type 39C is an advanced generation of CompactPCI chassis for PICMG 2.0, 2.16, 2.17, and EXP.0 applications. IEEE 1101.10/11, 6U x 160mm CPCI cards from the front and 6U x 80mm I/O cards from the rear.
-
Product
10-CH General Purpose Timer/Counter & 8-CH DIO Module
cPCI-8554
-
- PICMG 2.0 Rev 3.0- Four 82C54 programmable timer/counter chips- Up to 12-CH 16-bit timer/counter- 1-CH 32-bit cascaded timer based on 8 MHz clock source- Four programmable clock sources for each timer/counter- Programmable de-bounce filters for external clock & external interrupt inputs- 8-CH TTL digital inputs & 8-CH TTL digital outputs- +12 V and +5 V power available on the connector
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
3 PICMG® CPU, 4 PCI™, 7 ISA Slots Backplane
HPCI-13S4LU
-
- Segment: 1- Slots: 3 PICMG® CPU, 4 PCI™, 7 ISA- Supports AT, ATX power supplies- Dimensions: 314.7 mm x 259 mm
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
Other Backplane Architectures
-
Elma is well known for our backplanes based on common VITA and PICMG standards-based architectures such as VME, OpenVPX, and CompactPCI Serial. We also make backplanes for other architectures.
-
Product
CompactPCI 3U 4 slot 64 bit right justified RoHS, P1s P2s
102CPCI304-21XXR
-
CompactPCI 3U 4 slot 64 bit low profile with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 3U 3 slot right justified, 32 bit, P1s, P2s
105CP3R303-11XX
-
CompactPCI 3U 3 slot 32 bit with system slot right, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1. User defined VI/O is standard.
-
Product
PCI Express card carrier, PCIe Gen 3 x8 connection
SA4-COUNTRY
-
The SA4-COUNTRY is a peripheral slot board for PICMG® CompactPCI® Serial systems and acts as carrier for low profile PCI Express® Card. The SA4-COUNTRY is provided with a PCI Express® x8 connector.
-
Product
CompactPCI 9U 2 Slot, P1-2s, P3-5l, 1x P47
103CPCI902-3157R5
-
CompactPCI 9U 2 slot 64 bit Easyplug with P47 power connector, system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 6U 64 bit ATX 4 slot, P1s P2l, RoHS
102CPCI604-40X0R
-
CompactPCI 6U 4 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
CompactPCI 9U 8 Slot, P1-2s, P3-5l, 3 X P47
103CPCI908-5157R
-
CompactPCI 9U 8 slot 32 bit Easyplug with 3 x P47 power connector, system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
Product
COM Express Module
CM22202
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22202 is a Type 6 COM Express® module developed by LinkedHope® based on China local x86 architecture ZX® KX-6000 series Processors. This module pinout is compliant with PICMG COM.0 R3.0 specification. CM22202 contains all kinds of high-speed interfaces such as SATA III, USB 3.0 and PCIe 3.0. CM22202 provides dual-channel SO-DIMM, supporting DDR4-2666 MHz memory and the capacity up to 32GB.CM22202 supports KX-6000 series 4 core processors which TDP from 25W to 55W. CM22202 provides high performance computing with balanced power consumption. CM22202 works well in a wide range temperature environment. It is ideal for the high-bandwidth and processing intensive requirements of industrial and edge computing applications.
-
Product
14-Slot PICMG 2.16 6U CompactPCI Blade Server Backplane
cBP-6614A
-
- PICMG:2.0 R3.0, 2.1 R2.0, 2.9 R1.0, 2.11 R1.0, 2.16 R1.0- Dimension:Dimension 420.6 x 262.05 (mm, WxH)- 2.16 Node Slot:12- 2.16 Fabric Slot:2- cPCI Bus:None
-
Product
cPCI Serial Power Supplies
-
CompactPCI Serial (PICMG CPCI.S-0) has added a number of features and benefits while maintaining backward compatibility to create a foundational spec for serial-based CompactPCI technologies. This includes an updated power supply specification. CompactPCI Serial requires only one +12 V power supply with a maximum power of 79.8 W per 3U module and 171 W per 6U module as well as a 5V stand-by voltage.
-
Product
PICMG® 1.3 Full-Size 6th generation Intel® Core™ i7/i5/i3 LGA1151 Processor-based SHB (Code name: Skylake)
NuPRO-E43
-
The ADLINK PICMG 1.3 SHB, the NuPRO-E43, supporting the 6th Gen IntelR Core i7/i5/i3 processor and equipped with the IntelR Q170 Express chipset. The NuPRO-E43 supports high-speed transfer interfaces such as PCIe3.0, USB 3.0, and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2133 MHz memory up to 32 GB.
-
Product
cPCI Serial Chassis 9 Slots
4U 50HP
-
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by a 300W cPCI Serial power supply.
