Sources
The origin.
-
Product
Source Measure Units
NGU
Source Measure Unit
Thanks to their extremely high accuracy and fast load recovery time, the R&S®NGU source measure units (SMU) are perfect for challenging applications. A special ammeter design is used to precisely measure current drains from nA to A in one pass – no need to make multiple measurement sweeps. The instruments’ short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. With high speed data acquisition, every detail is detected down to 2 μs resolution.
-
Product
Light Source
UVF-204S
-
This is the ultra compact and light weight high power unit fully utilizing characteristics of the high stability and long life 200watt mercury xenon lamp.
-
Product
Radio Trigger Module
RTM3
-
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
Product
AC Power Source - 350VA to 1200VA
APS-4000
-
APS4000 Series is an AC power source from 350VA to 1200VA, output frequency: 45Hz-250Hz continuously adjustable (special frequency can be customized); Output phase voltage: withstand 1V-150VAC, high-grade 151V-300VAC, automatic gear 1V-300V.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
1KVA Variable Frequency Power Source
CX- 9001
-
Shenzhen Chuangxin Instruments Co., Ltd.
1KVA Variable-Frequency Power Source
-
Product
C/C++ Source Code Analysis
CODECHECK
-
CodeCheck is a programmable tool for checking all C and C++ source code on a file or project basis. CodeCheck is input compatible with all variants of Standard K&R C, Standard ANSI-C/C++, and all C and C++ compiler vendors. We support GCC-GNU Open Source C/C++ compilers. CodeCheck is designed to solve all of your Portability, Maintainability, Complexity, Reusability, Quality Assurance, Style Analysis, Library/Class Management, Code Review, Software Metric, Standards Adherence, and C++ Corporate Compliance Problems.
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
-
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
Product
Upgrade User-Installable GPIB Interface Board For AC6900B Series AC Sources
AC69GPBU
-
The AC69GPBU is a user-installable GPIB interface module upgrade for Keysight AC6900 Series basic AC power sources.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
Rotation Luminaire Goniospectroradiometer
LSG-1800CCD
-
LSG-1800CCD/LSG-1700CCD Goniospectroradiometer is an automatic goniophotometric instrument for luminous intensity distribution measurements with facility for turning the light source. The LSG-1800CCD can do the spatial CCT test when do the intensity distribution test. It is for industrial laboratory measurements the photometric data of luminaires such as LED luminaries, HID lamps, fluorescent lamps and so on.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
Multi-Intelligence Sensor Fusion
Insight
-
The Defense Advanced Research Projects Agency (DARPA) Insight program aims to develop an adaptable, integrated human-machine Exploitation and Resource Management (E&RM) System to make it easier for intelligence analysts to derive actionable intelligence from a growing number of sensors and data sources.
-
Product
6000 Series ATE（AC Source）
-
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
Product
Coaxial Directional Coupler, 2 GHz to 18 GHz
773D
-
The Keysight 773D is a high-performance directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler is ideal for leveling broadband sources when used with a Keysight 8474B detector. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
Product
500-1000W AC Power Source
CX-P150
-
Shenzhen Chuangxin Instruments Co., Ltd.
The AC power source is made by adopting microcomputer processing chip and high power device. It provides a stable pure sine wave and has voltage,
-
Product
Analog Input Products
-
Analog input boards are useful for measuring variably changing conditions in the real world. When we want to measure these variably changing conditions, we need analog inputs to convert these changing real world conditions to changing electrical quantities. For example, monitoring the temperature inside a wood kiln, or the water pressure on the output of a pump, or the heart rate of a medical patient. In each of these cases, you can use one of our analog input devices to convert the electrical data from a sensor or transducer into binary data that can then be used by your computer. The device that converts this data is known as an analog to digital converter (abbreviated ADC, A/D, or A to D). An analog input is a measurable electrical signal with a defined range. The analog input changes continuously in a definable manner in relation to the measured property. This data is very useful for process monitoring, process control, or simple monitoring / data collection and acquisition. ACCES' analog input boards amplify and multiplex input signals from thermocouples, strain gauges, accelerometers, photo sensors, flowmeters, RTDs, thermistors, voltage sources, millivolt sources, and current sources, just to name a few.
-
Product
Signal Amplifier
A10150
Amplifier
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
Product
24-Channel VME Synchro/LVDT Simulation/Acquisition Module
V545
-
The V545 is a generalized- DSP-based sinewave processor intended for both simulation and acquisition of LVDTs, RVDTs, synchros, and resolvers. 24 generalized, isolated channels are provided. Each channel can be a signal source or a measurement input. Users can program any desired relationship between input and output channels, allowing simulation and measurement of a wide range of inductive transducers, using internal or external excitation.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
Sound Power Solution
-
The Sound Power Solution is part of the family of solutions proposed by OROS for Acoustic applications. This Solution allows to measure Sound Power based on the measurement of sound pressure levels at microphone positions around a source under test. Thus, the Sound Power Solution is complementary of the Sound Intensity Solution that is based on the measurement of the sound intensity as recommended by ISO 9614. Using the OROS Solution, based on a task dedicated interface that guides the user step by step, Sound Power is measured in an easy and efficient way.?
-
Product
General Purpose Benchtop XRD System for Phase I.D. and Phase Quantification
-
In a move to bring lab-quality performance to the manufacturing floor, Rigaku introduces the MiniFlex XpC, a manufacturing-optimized powder diffractometer for fast and accurate quality control measurements. It is extremely easy to operate using Rigaku’s new EasyX quality control software, which requires minimal clicks to run. A minimal interface means there will be no accidental error variance from operator to operator. The MiniFlex XpC can be configured with a conveyor belt or robot for automated sample processing and collaboration with other instruments. With an 800 W X-ray source and a short-diameter goniometer, the system has the performance of a lab unit, and thus can greatly improve throughput for quality control measurements.
-
Product
Optical Signal Test Set
OST
-
The Optical Signal Test Set (OSTS) combines a state of the art optical power meter, a variable attenuator, and a high stability laser source. The unit is able to measure optical signals below -100dBm with 0.001dB resolution at a fraction of the size, power, and cost of competing solutions. Other features include data logging, programmable filtering, and auto calibration. Its small shielded ruggedized package, USB/power interface, and low cost make this unit perfect for lab use or for integration into larger systems.
-
Product
Zero Bias Schottky Detectors
-
Fairview Microwave’s line of coaxial packaged zero bias Schottky detectors feature matched inputs for excellent VSWR, voltage sensitivity levels that range from 100 to 500 mV/mW for small signal detection, negative video output polarity, and can withstand maximum input power levels up to +20 dBm CW. Operating temperature range covers 0°C to +90°C and storage temperature of -65°C to +125°C. These zero bias Schottky detectors utilize compact cylindrical package outlines that are made of passivated stainless steel and offer a variety of popular input/output SMA and BNC connector configurations that make them ideal for use with precision test and measurement, instrumentation, and subsystems assemblies. Numerous applications include power measurement, leveling pulsed signal sources, AM noise measurements, radar or missile guidance systems, monitoring system level performance, and pulsed RF measurements.
-
Product
Ambient PM TOF-MS FastTrack System
LAMPAS-3.0
-
LAMPAS adopts the single-particle aerosol time-of-flight mass spectrometry that can measure single particles' chemical composition and size in real-time and respond rapidly to a sudden source of pollution. Due to its versatility, LAMPAS is generally used to determine pollution sources in the urban, remote, and marine environment or verify the PMF module's accuracy to provide data reports to the environmental agency.
-
Product
Uniform Light Sources With Continuous Emission Spectrum
-
Tungsten halogen lamp based uniform light sources with options like manual or remote control variable intensity or monitor detectors.
-
Product
Power Measurement
-
Precision Acoustics manufactures Radiation Force Balances and Check Sources which can be used to measure ultrasound power according to the IEC Standard 61161. All products are supplied with a calibration from The National Physical Laboratory, LONDON.
-
Product
Open Compute Project ® Protocol Test Solutions
-
The global OCP community is a collaborative forum where vendors work together to improve how computing systems connect and interact. OCP equipment takes advantage of these improvements and open source designs to increase interoperability performance.
-
Product
Density Meter
-
Count on solutions from the source – Anton Paar has always been at the forefront of innovation in laboratory density and concentration measurement ever since we introduced the world’s first digital density meter. Today we offer a whole series of density meters, covering most requirements in various industries and R&D – from instruments with three-digit accuracy to the world’s most precise six-digit density meter, from handhelds to benchtop instruments. Anton Paar offers the right instrument for every application requirement – choose the density meter that best fits your needs.
-
Product
Light Source Colorimeter
CX-HP2
-
Shenzhen Chuangxin Instruments Co., Ltd.
Light source colorimeter is a newly developed pocket colorimeter, adopting advanced spectrometer and microprocessor technology. It makes traditional laboratory instrument available for the production on-line quality acceptance, thus greatly improve the efficiency of fluorescent lamp, CFL, LED manufacturing.
