FET
Rely on an electric field to control the shape and channel of a charge carrier in a semiconductor material.
-
Product
ORing FET Control
-
Renesas' ORing MOSFET Controllers with a suitably sized N-Channel power MOSFET(s) increase power distribution efficiency and availability when replacing a power ORing diode in high-current applications. They provide gate drive voltage for the MOSFET(s) with a fully integrated charge pump.
-
Product
FET Solid State Switch, 300 kHz to 18 GHz, SPDT
U9397C
Solid-State Relay
The Keysight U9397C solid state switch maximizes your frequency range from 300 kHz up to 18 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
-
Product
Integrated FET Regulators For Automotive
-
Renesas offers several buck, boost, boost-buck, and buck-boost integrated FET regulators for automotive applications.
-
Product
FET DIP Meter
-
* 1.3 to 30 MHz coverage* Small 350 uA meter movement* Five coils covers HF HAM band*95 turn #36 AWG coil comes pre-assembled* Measures 5.5 x 2.5 x 1.1 inch* 9 volt battery operation
-
Product
Active FET Probe Kit 1.2 GHz, 10x, ±40 V
CT4121
-
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design.
-
Product
PXI Solid State MUX, 4 bank, 40 channel
40-680-004
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Floating Power FET moduleAmp Loop
PFM1010
-
The PFM1010 Module is a precision instrument capable of measuring all common DC parameters in a power MosFet as well as many of the AC parameters. This module uses some very innovative techniques to make it possible to measure parameters like Rdson down into the sub-million-ohm range.
-
Product
Isolated Digital Input/Output Card
PCI-IDIO-16
-
The PCI-IDIO-16 is a low-cost, 6.8" card that provides isolated input and output for PCI-bus computers. The card has sixteen optically-isolated digital inputs for AC or DC control signals and sixteen isolated FET outputs. For safety reasons in working with AC voltages, insulating shields are provided with each card.
-
Product
PXI Multiplexer Switch Module
Switch Module
PXI Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
CobaltFx 9 GHz 4' FET RF Cable Kit
-
This is a Set of 4 cables, standard length 4 ft, for one extender: ULC50SMSM.4 cable (4)
-
Product
PXI Relay Module
Relay
PXI Relay Modules consist of multiple independent relays, such as single-pole single-throw (SPST), single-pole double-throw (SPDT), and double-pole double-throw (DPDT) relays. PXI Relay Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a set of relays that fit your requirements. To program the relays, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
FET Solid State Switch, 300 kHz to 8 GHz, SPDT
U9397A
Solid-State Relay
The Keysight U9397A solid state switch maximizes your frequency range from 300 kHz up to 8 GHz, offering excellent performance with high isolation, low SWR and fast switching speed. Applications include instrumentation, communications, radar, and many other test systems that require high speed RF and microwave SPDT switching.
-
Product
Volume Production Oscillators
-
Volume production oscillators utilize either high performance GaAs Gunn diodes with high Q cavity designs or state-of-the-art FET devices with dielectric resonators to yield excellent phase noise and stability. These oscillators are free running with extremely high frequency and power stability. The oscillators are generally designed and manufactured for fixed frequency applications. However, fine frequency adjustments can be achieved by mechanically tuning the provided self-locking screw. While the below standard models are offered for immediate production release, custom models are also available.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
Product
DC Power Supplies
SGe Series
-
AMETEK Programmable Power, Inc.
The SGe is an economical, FET based, high switching speed, programmable, dc power supply alternative to SCR and IGBT based dc supplies.
-
Product
Active Differential Probe
DF-600
-
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
Product
General Purpose Low-side MOSFET Drivers
-
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
Product
Switch Drivers
-
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
Product
IndustryPack Module
IP-OptoISO-16
-
The IP-OptoISO-16 is an IndustryPack Module with 16 optically controlled FETs [switch]. Each FET acts as a single pole normally open photovoltaic relay. The solid state approach has several advantages including bounce free operation, low on resistance, long life, fast switching, and higher reliability when compared to relays.
-
Product
Rad Hard Load Switches
-
Renesas' radiation hardened load switches provide a simpler and smaller way to turn on and off your power rails in multi-rail power systems compared to a discrete FET. Load switches are also ideal for redundant power distribution, power sequencing and input-output protection of POL based power distribution systems.
-
Product
Low CxR
-
Is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. A small flat-lead package has been provided which realizes a reduction in mounting area of about 50% compared withthe PS78xx series. It is suitable for high-frequency signal control, due to its low C × R, low output capacitance, and low off-state leakage current.
-
Product
FAult Detector and OScilloscope 7 Functions in 1 Device
FADOS7F1
-
Prot-Ar-Ge Industrial Project Design R&D Ltd. Co.
Usage of FADOS7F1: Determining faults of all types of electronic cards such as electronic cards of medical devices, textile and any other machines; automobile electronics; computer, monitor, TV, etc. Electronic Components Test: IC, transistor, FET, IGBT, resistor, capacitor, indicator, ect. This device is used to determine the faults at all these electronic components.
-
Product
Intelligent Power Devices
-
Intelligent Power Devices have built-in peripheral and protection functions, and support system reliability improvement and unit downsizing. This device lineup can support a variety of automotive system requirements and includes intelligent power switches, thermal FETs, MOSFET drivers, and a motor driver.
-
Product
Solid State FET Transfer Switch, 300 KHz To 18 GHz
U9400C
-
Offers outstanding performance in isolation, switching speed, and video leakage over a broad operating frequency range
-
Product
Mezzanine System
5235
System
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
Product
3000W-3200W 3-Phase Input Industrial AC-DC Power Supplies
TPS3000
-
The TPS3000 industrial AC-DC power supplies offer output power up to 3.2kW in a 2U high package with 3 phase supply input.Features include voltage and current programming, remote on/off, remote sense, a standby supply, PMBus communication, built in ORing FET and wide operating temparature range of -40°C to +70°C
-
Product
PXI Matrix Switch Module
Switch Module
PXI Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
PXI Solid State MUX, 4 pole, 40 channel
40-680-404
Multiplexer Module
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
X-Ray And Gamma Detector Systems
-
The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.
-
Product
DrMOS (Driver + FET)
-
Renesas' high-performance DrMOS power modules combine a high-performance FET driver and MOSFETs in an advanced package to create high-density DC/DC converters.
