Electro-magnetic
-
Product
Vacuity Testers Of Vacuum Switches
GDZK-IV
-
GDZK-IV is designed to measure the vacuum degree of vacuum breakers. It uses an electromagnetic discharge measuring method, to ensure the testing results accurate and reliable.The testing data can estimate vacuum breaker’s health and life span.
-
Product
Human Exposure Measurements to Luminaries
-
Through different ways of coupling between luminaries and humans, a level of exposure of a person to electromagnetic fields can be derived. One part of the exposure is based on capacitive coupling between lighting equipment and person. This creates induced internal electric field that must be evaluated using an EMI receiver and a Van Der Hoofden test head.
-
Product
PathWave EM Design (EMPro)
-
Electromagnetic (EM) simulation brings you insight before physical prototyping. Customize EM simulations for speed and accuracy. Integrate EM analysis with your circuit simulations.
-
Product
Power Divider/Combiner
-
Passive devices used mostly in the field of radio technology. They couple a defined amount of the electromagnetic power in a transmission line to a port enabling the signal to be used in another circuit.
-
Product
High Frequency Antenna Analysis Software
XGtd®
-
XGtd is a general purpose ray-based electromagnetic analysis tool for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas, and predicting radar cross section (RCS). It is ideally suited for applications with higher frequencies or very large platforms where the requirements of a full physics method may exceed available computational resources.
-
Product
Electromagnet
-
The electromagnet can generate strong magnetic fields for experimental applications. Depending on the required magnetic flux density and Equipment under test volume the air gap can be adjustedcontinuously. The magnet poles come with conical shape close to the test volume to improve accessability and to optimize the achievable magnetic flux density.
-
Product
Selective EMF Measuring Equipment
-
Selective measuring equipment for electromagnetic fields (EMF) for demonstrating safety and environmental compatibility. The devices analyze individual frequency ranges and field exposure levels accurately down to a single communications channel. They also calculate the sum and compare levels with current limit values.
-
Product
EMC Products
-
Products for demonstrating the electromagnetic compatibility of devices (EMC), i.e. for investigating inadvertent high frequency emissions that can interfere with other equipment as well as the immunity to irradiation that could interfere with a device.
-
Product
Measurement Technology for Teaching and Training
-
Is particulary suitable for training and further education. With the disturbance emission model, a variety of different experiments which improves one`s understanding of electromagnetic processes in modern electronic engineering are possible. The coupling mechanisms of disturbance emissions are visualized from their sources to the antenna. The impacts of EMC measures are then easier to understand.At VM 251 the electromagnetic d
-
Product
Inductive Sensors
-
Inductive Proximity Switches, self contained, depend on the output of an oscillator for their operation. The oscillator resonant circuit uses an open core coil to produce a concentrated high frequency electromagnetic (RF) field, which emerges from the active surface of the sensor. If a metal target (or other electrically conductive material) enters this field, eddy currents will be induced in it, causing the resonating oscillator to be damped.
-
Product
Waveguide Switches
-
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
Product
TERAHERTZ ROOM TEMPERATURE DETECTORS FROM 37.5 GHZ To 996 THz
-
Insight Product Company offers Golay cells that detect electro-magnetic waves at terahertz frequency ranges from 0.0375 to 996 THz.
-
Product
Spiral Antenna
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
Product
ESM/ELINT System
-
Shoghi’s Electronic Support Measures (ESM) are designed for electronic warfare techniques involving actions to detect, intercept, identify, locate, record, and/or analyze sources of radiated electromagnetic energy for the purposes of immediate threat recognition.
-
Product
Electromagnetic Radiation Tester
KM 196
-
Kusam Electrical Industries Limited
Unit : Electric Field : V/m; Magnetic Field : mT. Precision : Electric Field : 1V/m; Magnetic Field : 0.01 mT. Range : Electric Field : 1V/m ~ 1999V/m. Magnetic Field : 0.01 mT ~ 19.99 mT. Alarm Threshold : Electric Field : 40V/m, Magnetic Field : 0.4 mT. Reading Display : 3½ Digit Digital LCD display with Backlight. Frequency Range : 5Hz ~ 3500MHZ. Sampling Time : About 0.4 second. Measuring Mode : Dual Mode. Overload Alert : “1” appears on LCD. Sound & Light Alarm. Data Hold function. Auto Power Off. Average & Peak measurement. Low Battery Indication. Operating Temperature & Humidity : 0°C ~ 50°C; below 80%RH. Power battery : 9V Battery. Dimension : 63.6 x 31 x 125.8mm. Weight : Approx. 146g.
-
Product
Magnetometers
-
The strength of magnetic fields can be determined with a magnetometer. Regardless of whether in the private sector or in the work environment, the increasing use of technology and networking also increases the exposure to magnetic and electromagnetic radiation. This radiation can have a negative effect on living beings, but also on sensitive electronic devices. Many effects are so unspecific that radiation is often not recognized as the cause. With a magnetometer you can measure how strong the radiation is at your sleeping place, in the kitchen in front of the microwave or induction stove or at your workplace. The location of sensitive electronic devices such as a precision balance can be examined with the magnetometer. The extent to which the radiation intensity increases or decreases with distance can be determined by positioning the magnetometer at various distances from the radiation source.
-
Product
Lightning Detector/Storm Detector
SkyScan
-
The SkyScan detects electromagnetic emissions from individual lightning strokes, and can be detected at long range by use of ad hoc sensors. It is a hand-held instrument with an electronic system to detect the presence of lightning/thunderstorm activity occurring within 40 miles of your location.
-
Product
Clarity 3D Solver
-
The Cadence Clarity 3D Solver is a 3D electromagnetic (EM) simulation software tool for designing critical interconnects for PCBs, IC packages, and system on IC (SoIC) designs. The Clarity 3D Solver helps designers tackle the most complex electromagnetic (EM) challenges when designing systems for 5G, automotive, high-performance computing (HPC), and machine learning applications with gold-standard accuracy.
-
Product
EMC Testing
-
EMI is emitted radiation and its effects – a phenomenon. EMC is a device’s ability to limit the levels of unintentionally emitted EMI (that can harm other devices) and also a device’s ability to operate normally when subjected to EMI. Therefore, EMC testing seeks to ensure that a product possesses the characteristic of Electromagnetic Compatibility (EMC): the ability to limit creation of EMI (Electromagnetic interference) and the ability to operate properly when subjected to EMI. Stated differently, EMC testing measures the level of EMI control found in a device, and therefore helps to ensure that unwanted effects are prevented.
-
Product
1465 Series Signal Generator (100kHz – 67GHz)
1465
-
1465 series microwave signal generators, with the frequency range of 100kHz – 67GHz, is provided with high purity spectrum and high output power. It can meet the high-end requirements of electromagnetic signal tests. S1465 series are mainly used in the radar performance evaluation, high-performance receiver test and components parameter test etc., and applicable to aviation, aerospace, radar, communication and navigation equipment etc.
-
Product
Personal Safety EMF Measuring Equipment
-
EME (electromagnetic energy) RF Exposimeter / Personal monitors, worn on the person. The devices monitor the electromagnetic fields and warn of excessive field strengths, e.g. when working on industrial equipment, broadcasting or mobile phone stations, radar installations or other sources of electromagnetic radiation.
-
Product
Energy Efficiency Testing & Certification
-
In addition to testing equipment for product safety, environmental simulation, and electromagnetic compatibility, MET is a leader in Energy Efficiency Testing. Please choose an energy efficiency testing category: ENERGY STAR Testing & Certification for U.S. Environmental Protection Agency Efficiency Certification for Natural Resources Canada California Energy Commission Appliance Efficiency Program Energy-Efficiency Requirements for Europe
-
Product
Spiral Antenna UHF Trafo
-
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain. Its compact and robust design (passive sensor) makes Spiral antenna the optimal sensor for direct installation on high voltage Transformers. It can be virtually applied in any electrical equipment provided that it has apertures or EM transparent surfaces. Contact our sales department for consulting.
-
Product
Cable Harness EM Solver
MHARNESS
-
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
Product
Modeling Capacitors, Inductors, Insulators, Coils, Motors, and Sensors
AC/DC Module
-
The AC/DC Module is used for simulating electric, magnetic, and electromagnetic fields in static and low-frequency applications. Typical applications include capacitors, inductors, insulators, coils, motors, actuators, and sensors, with dedicated tools for extracting parameters such as resistance, capacitance, inductance, impedance, force, and torque.
-
Product
Inductive Heater
BD-1.01
-
The device is assigned to heat the bars to the state, which allows upsetting. The DB-1.01 heater characterizes especially high watt-hour efficiency (bigger than 98%) thanks to suitable concentration of electromagnetic field in the heating zone of inductor (the solution secured by patent). It is possible to addapt the nductive heater BD-1.01 for heating any others bars.
-
Product
RF Safety Monitoring
MVG EME Guard XS 6GHz
-
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
Product
RFID Tags
-
RFID tags bring the future of technology to today. Radio-frequency Identification(RFID) tags can be placed on almost any piece of clothing, cash, animals and even humans. Tags use electromagnetic fields to identify and track the desired object. Active tags are powered by a battery located inside the tag, and may operate over hundreds of meters away from the RFID reader. RFID tags have been expanding ever since their inception – they became especially popular when used in toll readers and assembly lines to track the product’s progress throughout the assembly line.
-
Product
EMC Testing
-
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
Product
Predicting Microwave and RF Designs Virtually
RF Module
-
The RF Module is used by designers of RF and microwave devices to design antennas, waveguides, filters, circuits, cavities, and metamaterials. By quickly and accurately simulating electromagnetic wave propagation and resonant behavior, engineers are able to compute electromagnetic field distributions, transmission, reflection, impedance, Q-factors, S-parameters, and power dissipation. Simulation offers you the benefits of lower cost combined with the ability to evaluate and predict physical effects that are not directly measurable in experiments.
