Fixed Attenuators
Fix the degree of attenuation.
-
Product
PXI 10 Channel High Voltage Attenuator
41-660-001
Attenuator
The 41-660 and 41-661 are high voltage attenuators designed to reduce the high output voltages commonly generated by some types of sensors. This is in order to produce manageable signal levels that can be acquired by typical data acquisition devices in a PXI system.
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
Product
PXI Dual RF Attenuator 63dB in 1 dB steps
41-180-022
Attenuator
The 41-180 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module.
-
Product
Programmable Step Attenuator, DC to 50 GHz, 60 dB, 10 dB steps
84905M
Attenuator
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
Product
Step Attenuator
RSC
Attenuator
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
Product
Attenuators
-
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
Product
RF Attenuators
-
Over 400 coaxial, surface mount, and MMIC attenuator models for 50-Ohm & 75- Ohm syetem including fixed attenuators, high-power attenuators, digital step / programmable attenuators, voltage variable attenuators and more. DC passing and DC blocking models. Power handling up to 100W. Bandwidths spanning DC to 50 GHz.
-
Product
RF Attenuators
-
Home > Products > Test and Measurement > AttenuatorsBird - The RF ExpertsRF AttenuatorsBird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
Fixed Gas Detector
OLCT 80
-
Teledyne Gas & Flame Detection
Oldham is pleased to propose its wireless system with the OLCT 80 field detector/transmitter. This model allows wireless connectivity in ATEX 1 zones.
-
Product
Variable Attenuator
VAXE
-
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
Product
Optical Attenuators
-
Guilin GLsun Science and Tech Group Co., LTD
Optical Attenuators by GLSN
-
Product
Digital Attenuators
-
Macom Technology Solutions Holdings Inc.
Digital Step Attenuators (DSA)are offered in up to 6 Bit control with lowest step size of 0.5 dB covering DC to 40 GHz. MACOM's DSAs can be controlled with serial and parallel control allowing for best implementation for our customers. These products exhibit low insertion loss and high attenuation accuracy and are offered both GaAs and Silicon (SOI) processes and are offered in both packaged and bare die form factors.
-
Product
Variable Optical Attenuators
5419
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Voltage Variable Attenuators
-
Macom Technology Solutions Holdings Inc.
Voltage Variable Attenuators (VVA) from MACOM offer the ability to control the attenuation level relative to a voltage. Attenuation range is up to 30 dB covering frequency as high as 45 GHz. VVAs feature excellent return and insertion loss along with high IP3 in small SMT packages.
-
Product
Package Converters & Fix Adapters
-
Package converters provide an electrical and mechanical conversion from one package type to another. We use gold plated interconnects for our pin and through hole converters. Ironwood Electronics offers solder column adapters as a solution for leaded SMT packages such as QFP, PLCC, SOIC, SSOP, and TSOP. This is an excellent choice when you have a PC board in production that needs an upgrade or you need to replace an obsolete part.
-
-
Product
SMA Rotary Attenuator
WATT-6SR1211
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Attenuators
-
OZ Optics offers a broad range of both variable and fixed attenuators having key competitive advantages. All of our attenuators operate over the two standard wavelength bands, the C-Band and the L-Band. This wide wavelength range makes these components ideal for DWDM applications. Our attenuators are wavelength insensitive, which means they operate with minimal changes in attenuation when used in either the C-Band or the L-Band and exhibit low return loss. In addition, all of our attenuators have a wide attenuation range, which means they operate at a wide range of power levels. This is important as increased power levels are being used in newer optical systems.
-
Product
Fixed Systems
-
Low cost versatile solutionCompact, weatherproof, NEMA 4X enclosure115/220 VAC or 24 VDC operationLong life sensors (2+ years typical)Accepts RKI LEL/O2/H2S/CO direct connect sensorsAccepts any 4-20 mA transmitterAudible alarm with reset buttonTwo programmable alarm levelsBuilt-in trouble alarm with relayRelay rating 10 amps, form CProvides 4-20 mA output
-
Product
Fixed Clamp-on Flowmeter
D116
-
Gentos Measurement & Control Co.
D116 Series Ultrasonic Flowmeter is a state-of-the-art universal transit-time flowmeter designed using FPGA chip and low-voltage broadband pulse transmission.
-
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Manual Attenuator (Waveguide)
-
RF Lambda’s manual waveguide attenuators are used to control signal levels using a manual control knob. These are commonly used in test setups or systems where an operator is present and there is a need to change signal levels manually.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
Product
Fixed Telephone Communication
-
PBE provides Fixed Phone Voice Communication for safe, efficient and reliable underground operation.Two-way voice communication underground is a necessity to provide a safe and productive work environment. PBE offers a number of fixed phone solutions that can be deployed to provide secure voice communications. Solutions can be analogue or digital and be either stand-alone or integrated into PBX and mobile infrastructure.PBE Fixed Telephones provide clear and undistorted communication throughout the entire underground phone system. PBE telephone networks are compatible with other analog and VoIP phones on the market today which allows to combine different products for a complete communication system above and below the ground.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
Fixed Magnification Interferometer
FiBO 250
-
FiBO 250 offers a solid and economical solution to automated fiber testing by bringing together full 2D visual inspection capabilities and true phase-shifting interferometry to achieve exceptionally accurate measurements. A fixed focal length 10x magnifier ensures maximum system stability and a very high level of repeatability.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 110 dB, 10 dB steps
8496A
Attenuator
The Keysight 8496A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
