-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
Product
Press Down Rods Bed of Nails Testers
RandHDPE HDPE Family
-
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
Product
Fiber End-face Interferometer
-
Anfkom International Co.,Limited
1.Automatic MeasurementSANA2 is equipped with the locking handle sensing unit to monitor the device locking status. To further simplify the testing process, the instrument can start the measurement once the device to be tested is fully locked. Operator can also click the button aside the locking handle to trigger the measurement.2.0~12° APC Angle Auto TuningBenefit with the unique fixture design, SANA2 can tune the APC angle precisely from 0°to 12°automatically, meeting any special requirement on APC angle setting.3.Simple and User Friendly Interfaces and Excellent 3D ImagesThe software of A 2 is simple and user friendly, you can change the language within the software. It provide many endface rebuild method such as 3D, 2D, plot to assist the engineers about the process. The test reports and data are generated automatically for analyzing and tracing.4.Auto Centering ImagesSANA2 has auto centering image function that can find the fiber and makes it to center automatically within one click.No mouse drag or hardware adjustment is needed.5.Cleave Angle Measurement
-
Product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
-
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
Product
Architectural Preset Stations
SceneStation
-
Interactive Technologies, Inc.
SceneStation sets a new standard for full-featured, easy to use, cost-effective DMX lighting control. SceneStation is entirely self-contained in a single gang wall switch sized unit. Perfect for restaurants, high-end residential, trade show booths and more, SceneStation can control nearly any DMX device (RGB fixtures, moving lights, dimmers, effects, etc.), while also remaining very simple for the end user.
-
Product
Drop-In In-Circuit Test Fixtures
The Chameleon
-
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
Product
DC Power Module, 8V, 12.5A, 100W
N6742B
Power Module
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Testing Aircraft Thrust Reversers
-
Custom Dynamometer Table. 2WB 115 Eddy-Current Dynamometer: with protective cover. DSP6001 High-Speed Programmable Dynamometer Controller. Customized Motor Fixture. RER 350 Cooling Unit
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
Structural Durability Products
-
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
-
Product
DataComm
-
SCHILLER AUTOMATION GmbH & Co. KG
With ever-growing performance, accuracy, and precision required by 112G/800G PAM4 solutions, Wilder has designed a robust HCB and MCB fixtures to support OSFP-XD, QSFP-DD, OSFP and SFP-DD compliance testing. In addition, CMIS_GUI Software provides: Displays of many of the settings and Controls in the Module including Lane States, Module Power States and Optical Power. Alarms and Warnings for Module Temp and Vcc and Optical Power Controls for Module Power, Margins, and read access to Descriptors and Data Path Configuration. Direct Read/Write access to the I2C and CMIS Memory Map as well Scripts that directly access the CMIS Memory Map Registers.
-
Product
USB-C® – USB 2.0 C Receptacle to A Plug
AUT17032-CRAP
-
This fixture is designed for USB-C 2.0 Plug and USB-A products.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
F9 Systems CalBlade
-
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
-
Product
Phase Array Ultrasonic Testing
PAUT
-
Sensor Networks, Inc. (SNI) is a Pennsylvania-based technology company specializing in the design and fabrication of industrial ultrasonic transducers and tooling for demanding in-situ test and inspection applications. Engineered for precision, ease of use, and maximum durability, our offerings include Phased Array ultrasonic transducers, fixtures, couplant-delivery systems, qualification/calibration standards, procedure development, personnel training and instrumentation.
-
Product
In-Circuit Test Fixture Design Services
-
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
Product
Magnetizing Fixtures
-
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
Product
Large Kelvin Clip Lead
16089A
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
Product
Flash Programming for Functional Test Systems
-
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
Product
CTR Test Fixtures
-
Designed to hold electronic components or assemblies in place during testing, particularly for verifying the Current Transfer Ratio (CTR) of optocouplers.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 335 x 250 mm (wxd)
CMK-02
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Custom Test Fixtures
-
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
Product
Deep And Sloped Pan Fixtures
-
Line of deep and sloped pan fixtures for general purpose/system non-specific pcb test applications. H+W Test Products manufactures test fixture products for in-circuit, functional and combinational testers for users of automated test systems (ATE) such as Aeroflex, Agilent (HP), Checksum, Factron, Teradyne (GenRad), Test Research (TRI) and Testronics.
-
Product
Computer Networking Solutions
-
Today’s world has a never ending appetite for data. Everywhere you look there are connected devices that provide and consume that data at an astonishing rate, and the demand increases every day. Our computer and networking customers are constantly pushing the edges of technology to deliver data faster and more reliably than ever. They use the newest electronics available to keep our data flowing – data that is critical to the operation of the world’s infrastructure. As cutting edge technologies are developed, these faster more advanced capabilities require the most sophisticated testing available. Circuit Check is constantly evolving our test fixtures and systems to meet this industry’s most advancedrequirements.
-
Product
Manual Fixture Kit
230371 – CMCSK-02-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Universal Test Fixture
CAM/GATE
-
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
