PCB Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Test Fixtures, Board Test Fixtures, ATE Fixtures, Bed of Nails
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Functional Fixtures
-
Joule''s strength is in the design and manufacture of functional test fixtures. Using 3D modeling software to create the fixtures allows us to actuate pneumatics, open and close overclamps, actuate side access units - all before a single part has been machined for the fixture.
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/GR228x-15/15
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,46 kg
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
-
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
Cable Continuity Test Fixture
CCT
-
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
26-Pin D-Type Female Right Angled PCB
40-963-026-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Cable-End Test Fixtures
-
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
Product
Precision LCR Meter With Component Fixture And Limits Comparator
LCR400
-
0.1% basic measurement accuracyDual 5 digit high brightness displaysAutomatic component recognitionBuilt-in 4 terminal component fixtureLimits comparator with 8 Pass bins plus 2 Fail binsThree test frequencies, switchable biasRS232 interface standardOptional SMD tweezers, BNC connectors, Kelvin Clip test lead set, and PC logging software
-
Product
Functional Test Fixtures
-
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
Product
SAS Protocol Test System
Sierra M124A
-
The SAS Sierra M124A Protocol Test System is Teledyne LeCroy's 7th generation protocol analyzer system that provides 100% accurate protocol capture of both SAS (SAS 3.0) and SATA (SATA 3.0). The industry's most widely used test platform for SAS and SATA features unmatched analysis and debug capabilities to help pinpoint problems at every layer of the protocol.
-
Product
Custom Test Stands/Production Test Cells
-
Emprise Corporation is an engineering consulting firm serving the automotive, aerospace, industrial and alternate power industries. Our expertise in each of the individual fields of technology, systems integration, construction management, and integrated test facility design and delivery sets Emprise apart from other single-source engineering firms.
-
-
Product
Wave Profiler Fixture
KIC® Wave Surfer™
-
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
Product
Intelligent PCB Inspection
-
It uses a proprietary image analysis system based on Artificial Intelligence. Eliminates time-consuming (re)programming of the process thanks to advanced self-learning. Guarantees high efficiency of the error detection process regardless of the type of component or PCB being inspected. Effectively supports decision-making processes in the area of quality control. Fully compatible with every production line. Ideal for high-variability production models thanks to self-configuration.
-
Product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
-
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and allows for sourcing the composite signal from the paired radio or from an external generator. The DME channeling outputs are monitored with discrete LED's as well as the ILS, V/LOC, Glideslope and NAV TEST valids. Discrete test jacks are provided for all the meters and the resolver of the NAV indicator and a dimming source is also provided. When testing the RMU 5000 computer access is through a dedicated connector.
-
-
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
VOC FIXTURE OVER CLAMP ASSEMBLY'S
-
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
Product
Test Probes
-
Petracarbon is a leading supplier and provider of spring contact probes and semiconductor test sockets.
-
Product
ICT/FCT-Fixtures Max UUT370 × 300 mm (wxd)
CK-2 Large (Hold-Down Gate) / 230158
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Automated Testing
TestComplete
-
Got an aggressive testing schedule? No problem. With this automated testing tool, designed for advanced and novice testers alike, you can create, manage and run tests for any desktop, Web or rich client software. Revel in the easy-to-use interface and script-free testing combined with a powerful set of customization features.
-
Product
Streaming Testing
-
Our streaming testing services ensure your customers enjoy the best experience in every territory and on every screen. From performance monitoring to benchmarking and regression testing, we understand the importance of having a reliable and bug-free experience. Our teams help reduce potential risks and ensure your content gets delivered flawlessly.
-
Product
PCB Triaxial Accelerometer, 1000mV/g, ICP®(IEPE), 0.5Hz-3kHz
784815-01
-
The PCB Miniature Triaxial Accelerometer helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB Miniature Triaxial Accelerometer features a sensitivity range of 1000 mV/g and requires the PCB lightweight cable with 4-socket plugs.
-
Product
Optical Test
-
Optical components such as micro-lenses, diffractive optical elements (DOE), meta optical elements (MOE) and micro lens arrays (MLA) are now largely used on consumer electronics and even more optical elements need to be integrated into smaller and smaller packages. Nowadays mass-production industries key to success lies in increasing the yield by means of strongly automatized testing machines, with statistical analysis.
-
Product
96-Pin SCSI Micro-D Straight PCB
40-963-096-SF
-
Ideal for user created termination schemes where the termination is to be on the front of the product or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Test Automation
-
Deployment ramping up pressure on the test organization to validate products in shorter test cycles. We have assisted Tier – 1 companies in the BFSI, Cloud Solutions and Communication domains to deploy highly efficient test strategies. Talk to our engineers to see how we can assist your business.
-
Product
78-Pin D-Type Male Right-Angle PCB
40-963-078-RM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
