PCB Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Test Fixtures, Board Test Fixtures, ATE Fixtures, Bed of Nails
-
Product
Oil Test Cell Heater
-
• Dry type heater for oil test cell • Temperature setting of 20º -110ºC auto cut-off • Quick heating (RF Induction) from inside & outside
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Smart Home Device Testing
-
Helping you ensure that your smart home devices with integrated wireless modules meet requirements to demonstrate compliance to global wireless type approval requirements.
-
Product
Testing Execution on Demand Services
-
With On Demand services, you only have to pay when you need our expertise. This can save you both time and money in comparison to keeping additional staff on the payroll.
-
Product
Test Pattern Generators
-
Video Test Pattern Generator, Portable Monitor Tester, Test Video Audio Signals, HDMI, DVI, SDI, Component Video, HDCP
-
Product
Bucket Liner Test Equipment
-
Liners are tested using the same principles as insulated rubber gloves. Full electrical voltage applied. Units sized for either single or dual liner.
-
Product
FCC-Recognized Accredited Testing & Certification
-
Helping you ensure that your radio devices or devices with integrated wireless modules meet requirements to demonstrate compliance to FCC requirements for approval.Manufacturers planning to sell their wireless/RF products in the United States must ensure that their equipment won’t electromagnetically interfere with other products or cause harm to the public as enforced by the Federal Communications Commission (FCC), per Title 47 of Code of Federal Regulations (CFR).
-
Product
Electrodynamic Vibration Test Systems
i-series
-
Vibration tests have become diversified and specifications have become increasingly strict.i-series offer a user-friendly lineup with enhanced performance and durability.
-
Product
Fumonisin Testing Solutions
-
Fumonisins are mycotoxins produced by the fungus Fusarium moniliforme. F. moniliforme is a frequent, almost universal, inhabitant of corn. Fumonisin B1, B2 and B3 are present in most corn samples tested, often totaling greater than 1 ppm. Fumonisin is thought to cause equine leukoencephalomalacia in horses, swine pulmonary edema, and human esophageal cancer. The FDA/USDA Working Group on Fumonisin advises less than 4 ppm for products for human consumption, less than 5 mg/kg in horse feed, less than 10 mg/kg for swine feed, and less than 50 mg/kg for cattle feed.
-
Product
EMC Testing EMCD
-
Efficient and flexible EMC testing services for product CE marking, UKCA marking and demonstrating compliance with US FCC and Canadian ISED regulations. Our experienced engineers will guide you through the test process, helping you to save time, minimise project costs and get your product to market quickly.
-
Product
Ventilator Test System
4070
-
The Certifier® FA Ventilator Test System 4070 is capable of testing multiple parameters of ventilator performance. It is designed to measure air, oxygen, and nitrous oxide flow and pressure in institutional, home care, field service, laboratory, and production applications. The Certifier FA ventilator test system is a battery-operated flow analyzer that can also test a variety of other medical equipment such as anesthesia gas delivery machines and oxygen concentrators.
-
Product
10Gbit Ethernet Test Engine
XGT-200
-
The Ethernet test engine XGT 200 provide a comprehensive test for next generation Ethernet solution. There are many different test modules, it can help clients to verify the performance of their Ethernet. XGT-200 have two 10/100/1000Mb/s RJ45 , two 100/1000M SFP and two 10Gbps SFP+ it can generate test profession streams that you need and analyze them ,then provide the test result. XGT-200 provide install and maintain services and activate new profession service. XGT-200 can provide many kinds of test functions, it can help you to control and know the quality of your Ethernet.
-
Product
Test Software
-
American Probe & Technologies, Inc.
This new series of software allows you to analyze materials or semiconductor leakage with all of the capabilities of your HP 4140B to resolutions of 1 fA @ 100VDC. Completely rewritten in Visual Basic for Windows XP operating system, it offers Virtual Front Panel Operation of 4140B for I-V & CV Analysis and allows operator to virtually control the 4140B for any instrument operation. I-V Plots with options of displaying current over time. CV Plots with high resolution plotting capability.
-
Product
Tactical Radio Test Set
CTS-6100
-
The CTS-6100 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
Product
Waterproof Test Chamber
JL-XC
-
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
Product
Primary Injection Test System
-
HAOMAI Electric Test Equipment Co., Ltd.
Primary injection testing is suitable for testing over-current trip relays attached to a circuit breaker.
-
Product
Signal, Module, Receiver, CASS, 210 Position, Right Angle PCB Mount
510113124
-
Signal, Module, Receiver, CASS, 210 Position, Right Angle PCB Mount.
-
Product
Flexible Pitch GND Fixture Clamps
GF-A
-
High Power Pulse Instruments GmbH
*Compatible with GGB picoprobe model 10 replacement probe tips*<1 ns rise time (200 ps possible with 5 mm GND wire length)*Custom selectable GND wire length 5-15 mm*Gold-coated spring-steel clamp with micro-machined groove for locking of the clamps on the probe tip*High conductivity and low inductance copper HF litz wire with 200 x Ø 0.02 mm strands*Easy to use clamping*Tungsten carbide probe needle with 1 inch length, 15° taper and 7.5 µm tip radius
-
Product
A to Z Testing
-
Elemental Analysis has the ability to analyze, and to test for all of the substances listed below, and many more. If you do not see the substance you need analyzed or tested for, please give us a call! We can test almost ANYTHING!
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2 Medium (Hold Down Gate) / 230156
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
-
-
Product
Spring Stiffness Testing Machine
STB Series
-
Jinan Testing Equipment IE Corporation
STB Computer Control Spring Stiffness Testing Machine Under Axial and Lateral Load is to measure the displacement stiffness of spring under both axial and lateral load, complying with the standard EN13298 Railway applications - Suspension components - Helical suspension springs, steel. The Spring Stiffness Testing Machine measures both axial and lateral stiffness of spring, displacement for both lateral and axial, both loads, offset angle etc. The Spring Stiffness Testing Machine is an ideal testing equipment for spring of chuck and train.
-
Product
API Security Testing
-
In the world of digital civilizations, use of API is getting popular increasingly as a technology enabler and it connects various applications and micro-services through end points. Hence securing these end points are quite critical for businesses to protect the confidential data. QA Mentor uses the concept of API Fuzzing by providing random data to the target API until any unexpected behaviours or errors are observed. In addition, QA Mentor uses other applicable methods of API security testing like SQL Injection on target API, tampering of API parameters etc. We follow a strict 10 pointer checklist in our API software security testing services process to ensure better coverage:
-
Product
Accelerated Stress Test Chamber
-
CSZ's accelerated stress test chambers combine mechanical refrigeration; LN2 cooling and high velocity air flow for fast product temperature change rates. Chambers are typically designed with a change rate up to 30C (54F) per minute based upon the part temperature. Common uses are production stress testing circuit boards, electronic drives, assemblies, etc. Design allows the user to quickly control and change the temperature of the product.
-
Product
Production PCB Combinational Tester
-
The PT100Pro combines ARM Functional Test, Analog Test and Boundary Scan in one platform for testing up to 32 PCBs at a time. The PT100 Pro solves the test challenges and cost requirements of testing small, high-volume PCBs used in the home, mobile, entertainment, automotive and embedded markets. PCBs in these markets are cost sensitive yet require high volume, high fault coverage on leading edge technologies such as WiFi, DDR Memory, USB, Bluetooth, Nand Flash, MPEG decoders, Power Management Units, and MMC/Smart Cards interfaces.
-
-
Product
Torque Gauges and Test Stands
-
SHIMPO offers a torque product line that is suited for accurate and precise testing.
-
Product
EZ Test Texture Analyzer
-
- For the Scientific Evaluation of Food - "My tester" performs rheology property evaluations on food and strength evaluations on medicines and pharmaceuticals. This tester can easily provide high-precision data with excellent reproducibility for a variety of fields whenever needed. It is useful in a wide range of fields since it can quantify the texture properties of foods, medicines and pharmaceuticals, such as bite texture, sensation and palatability, perform QA evaluation according to changes in hardness, and perform strength evaluation of food wrappings.
-
Product
Rain Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Rain Test Chamber is used to test anti-rain and waterproof performance for products, the products such as .steam locomotive lamps, wiper performance, waterproof bands, motorcycle instruments, defense industry, navigation systems, missiles, radar cone top, aerospace industry, IEC IP code specifications that need an additional discussion.
