Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
Product
DMX to Analog Interfaces
-
The MTX-DE48 decodes signals from DMX control desks to analog dimmers. It is used to integrate DMX controllers into existing analog installations. The standard 0 to 10V output is compatable with many LED drivers. Output may be adjusted up to 28V for use with some older dimmer systems. A negative output voltage option is also available.
-
Product
Run Down Adapters
Mini RDA
-
The mini RDA unit with fastener is designed for low torque sensors. Engineered to provide consistent and reliable torque readings for use with low torque power tools. The mini run down adapter is mounted in-line between the tool drive and torque sensor.
-
Product
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort
510171116
PCB Adapter (ITA)
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort.
-
Product
C Series CANopen Interface Module
CAN Interface
The C Series CANopen Interface Module is a high-speed interface for developing CANopen applications. CANopen is a higher-level communication protocol based on the controller area network (CAN) physical layer. It was designed for motion-oriented machine control networks, but now it is used in a variety of products and applications, including medical equipment, maritime electronics, building automation, and more. The C Series CANopen Interface Module can transmit and receive process data objects (PDOs) and service data objects (SDOs) according to CiA-DS 301. Using the NI-Industrial Communications for CANopen driver, you can batch edit SDOs, configure slave nodes with LSS services support, as well as perform network management (NMT), heartbeat, node guarding, and CANopen synchronization functions.
-
-
Product
Intelligent Interface Card
IIB-1553-PC104
-
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
Product
Adapter, APC-7 to Type-N (m), DC to 18 GHz
11525A
Contact Adapter (ITA)
The Keysight 11525A is a general purpose grade, APC-7 to type-N male adapter.
-
Product
PCIe Adapter for PMC
PCIeBPMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
Product
External Contact Adapter
DT141
-
This MicroLog sensor monitors Reed Relay contacts and switch status (open/closed), to identify the correlation between phenomena such as temperature change and door status.
-
Product
High-Stability Adapter
10723A
-
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
Product
Interface Solutions
-
The 1394 and AS5643 interface cards define new standardsfor standard OHCI and Extended OHCI host connectivityand set new standards for 1394 and AS5643 data I/O.
-
Product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-01
Transceiver Adapter Module
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
Product
KYK-13 Interface
IP-Crypto
-
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
-
Product
NI-5781 , 40 MHz Bandwidth, RF Adapter Module for FlexRIO
781267-01
RF Adapter Module
The NI‑5781 is an analog dual-input, dual-output FlexRIO adapter module optimized for interfacing with baseband to RF upconverters and downconverters. When you pair the NI‑5781 with a PXI FPGA Module for FlexRIO, the resulting NI‑5781R is an FPGA-enabled reconfigurable I/O (RIO) baseband transceiver that you can use to implement custom RF modulation and demodulation, channel emulation, bit error rate testing, or spectral monitoring and jamming. Additionally, you can use the low latency and high throughput of FPGA‑based processing for ultra‑high‑speed control and inline processing applications.
-
Product
High-Performance IEEE-488 GPIB Interface for USB
USB-3488A
Interface
ADLINK"s GPIB interface solutions are delivered with complete software support, including a driver API set that is fully binary compatible with NI-488.2* driver. All programs written based on the GPIB-32.DLL library can be executed with the USB-3488A without any modification. The VISA library is also supported to ensure compatibility with applications utilizing VISA. Regardless if you are using VC++, VB, Delphi, LabVIEW*, or any other T&M ADEs. The ADLINK USB-3488A provides "Plug and Play" compatibility with all your existing applications.
-
Product
EBIRST 50-pin D-type To 9-pin D-type Adapter
93-005-238
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
EMI Filters & Adapters
Emissions
-
The commonality in this section is conducted noise. Noise is not just a consideration when complying with EMC legal requirements, its is also potentially damaging and/or cause of failure of product performance or communications, even if the noise level is below EMC standards limits.
-
-
-
Product
PMC to PCI adapter
3390
-
PMC to PCI adapter - permits operation of PMC in a PCI slot for engineering development
-
Product
Ethernet Interface Module
-
Ethernet modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the Ethernet link untouched.
-
Product
Adapters & Converters
-
Using our prebuilt, off-the-shelf standard adapters, custom converters, or custom adapters, incorporate performance and process data from across your enterprise, without having to disrupt your manufacturing line or change the outputs or your manufacturing process.
-
Product
LC Adapters
FY3
-
FIBERYO LC Adapters are available in simplex and duplex configurations. They feature self-adjusting panel latches as well as a choice of mounting orientations and labeled polarity.
-
Product
Interface ICs
-
Easy to use, flexible, and reliable. Allegro’s sensor interface ICs offer accurate and fast output for signal conditioning in a wide range of applications, from electric vehicle HVAC systems to transmission oil pressure. Our innovative algorithms deliver robust EMC performance and provide critical diagnosticsthat support automotive safety.
-
Product
Pulse Adapter
CV30 P300
-
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
-
Product
Avionics Interface Technology
-
The modules are available as PXI, PCI, PCI Express, USB, VME, VXI and many more
-
Product
RF Adapters
-
Amphenol RF offers a full range of coaxial adapters designed for radio frequency applications. RF adapters feature all industry standard interfaces in between-series and in-series configurations to support a wide assortment of applications.
-
Product
XA GPIB Cable Adapter
181638-01
GPIB Cable
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Male or Female GPIB (IEEE 488) Adapter - The GPIB Adapter connects GPIB cables to other accessories. NI offers it in Type XA, XE, and XF.
