Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
Product
Low Noise Filter Adapter
PX0107A
Adapter Module
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
Product
Automated Test Interface
ATI-100
-
Matrix Test Equipment Incorporated
Now, with our ?New? Model ATI-100 you can turn your existing Matrix Signal Generator and Switchable Filter Bank into a full-blown DTS (Distortion Test System). Plug and play is the word, just plug in your Multiple Frequency Signal Generator, Switchable Filter Bank, Spectrum Analyzer, Oscilloscope, Power Meter, Frequency Counter, etc. to allow the following automatic testing with a single insertion of DUT (device under test
-
Product
Protective Cover, G20, 6.75" Series Adapters, ITA
410112797
Protective Cover
Protective Cover, G20, 6.75" Series Adapters, ITA
-
Product
Isolated Four-Port Serial Interface Cards
PCI-ICM422-4 and PCI-ICM485-4
-
These cards can be installed in any 5-volt PCI-bus computer that can accommodate "long" cards and are designed to provide effective communication on long communication lines in noisy environments. The data lines are opto-isolated from the computer and from each other to assure communication even when large common mode noise and voltages are superimposed. Type 16550 UARTs are used. These include a 16-byte transmit/receive FIFO buffer to insure against lost data in multitasking operating systems. All ports are independently addressable and an on-board crystal-controlled oscillator permits precise selection of baud rates up to 115,200 baud or, by changing a jumper, up to 460,800 baud.
-
Product
Data Acquisition Products by Interface
-
Wide range of measurementsPC-based or stand-alonePrices start at $599Software included
-
Product
Wireless Airflow Temperature Humidity Adapter
DTHA2
-
UEi Test & Measurement Instruments
Airflow Temperature Humidity Adapter with Free App
-
Product
RF Adapters
UHF Adapters
-
Are general purpose units developed for use in low frequency systems from 0.6 - 300 MHz.
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
PCI Express 16 Isolated Input Digital Interface (10-30V)
8006He
-
Optimized for sensing up to 24V inputs, the 8006He PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
VXI Register-based Interface Board
-
VXI Register Interface mates with user's PCB to form a B or C-size module.
-
Product
PMC Compatible Wizard Interface
PMC-Wizard
-
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
-
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
VisualDetect LCD Voltage Detector / Interface Tester
VDL-01AB
-
Hachmann Innovative Elektronik
VisualDetect LCD is an easily operated voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces. Additionally the LC-display indicates the measured current [I/A] and frequency [f/Hz]. Thanks to the integrated configuration menu it can be adjusted to switchgears operated below nominal voltage on-site.
-
Product
PCI Adapter for cPCI
PCI2cPCI-32
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6778
-
The Technobox, Inc. P/N 6778 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
Product
Test Adapter
FECVF1600
-
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
Product
4-Port Serial Interface
APCI-7500-3
-
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
IEEE 488 PXI GPIB Instrument Control Module
778039-01
Serial Interface
The PXI‑GPIB is an IEEE 488 controller module for PXI systems. You can use this module to integrate non-PXI instruments into your PXI system using GPIB. The PXI‑GPIB achieves maximum IEEE 488.2 transfer rates. This module … includes a license for the NI‑488.2 driver software, which provides maximum reliability for connecting to third-party instruments with GPIB.
-
Product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
Module
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
Product
DAS Trays/ Point-of-Interface (POI)
-
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
Product
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through
LPA-2.92-PX-KIT
-
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through.
-
Product
Wireless Interface
Quasar 7Z01300
-
The Quasar module provides a way to use Ophir sensors as a remote laser power/energy meter allowing optimum placement of the sensor and separate optimum placement of your PC or laptop with no connecting cables.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 50 to 67 GHz
V281A
-
The Keysight V281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Cable Assembly, Receiver, QuadraPaddle & Mini Coax, 36", PCB Adapter
540103010258
Cable Assembly
This cable assembly comes with PCB adapter 510150210 and a Mini Coax module to 4 SMB plugs.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
