Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
Portable Monitoring Receiver and RF Recorder
IZT R3301
-
The IZT R3301 is a portable receiver with an integrated server for data recording. The receiver is optimized for recoding of RF signals in frequently changing environments. The RF characteristics of the IZT R3301 are identical to the IZT R3000 series. # HF-VUHF-SHF receiver# frequency 9kHz...3GHz (3...12GHz option)# continuous spectrum recording of 24 MHz bandwidth, IQ recording with 20 MHz
-
Product
AC/DC Digital Clamp Tester (CE)
M-270
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*True rms reading for ACA and ACV.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Auto zero adjustment for DC current offset.*Conform to IEC safety requirements.
-
Product
Auto Oxygen Sensor
KS60004
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Continuous-wave (CW) Lasers
-
Continuous-wave lasers (cw lasers) emit a continuous laser beam as compared to ultrafast or pulsed lasers that emit a pulsed laser beam. Spectra-Physics offers wavelength tunable cw lasers, standard cw lasers, quasi-cw lasers, and accessories for continuous-wave lasers.
-
Product
10MHz DDS Function Generator With Counter
TG1006
-
0.001Hz to 10MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logUnique manual sweep gives quasi-analogue controlAM and FSK modes, frequency list (10 steps)2mV to 20V pk-pk from 50 or 600 OhmsBuilt-in seven digit 120MHz frequency counterLow cost
-
Product
Bench Power Supply, Adjustable, 1 Output, 300 mV, 30 V, 0 A, 4 A
72-2660
-
Compact and light weight design is the size of a handheld multimeter. A large, back-lit LCD is easy to read, and brightly back-lit buttons are easy to use. Efficient switch mode power supply is rate up to 50W continuous power, providing up to 12 volts at 3. 75 amps, or 30 volts up to 1. 6 amps.
-
Product
Watchdog Timer Card
PCI-WDG-CSM
-
This multifunction card contains a watchdog timer. Additionally, one or more options may be included on your card. These are: a computer power supply monitor, a computer internal temperature monitor, an optional capability to read the temperature, a fan-speed monitor, and an on-card buzzer to signal watchdog timeout. PCI-WDG-CSM continuously monitors critical PC functions. When a fault occurs, the card automatically generates outputs that can be used either to initiate corrective action or to generate alarms.
-
Product
Load Cell Electronics
-
All our electronics are continuously evolving to feature faster and more powerful components. This commitment to innovation ensures that we can meet any new challenge or application.
-
Product
CombiVolt™ 1 Voltage/Continuity Tester
DL6780
-
Testing of AC/ DC voltages from 12 to 690 V AC/DC Continuity testing with optical and acoustic indication Automatic switching between voltage and continuity Phase rotation test system Single pole phase indication Fully compliant with GS38 Fully operational voltage indication even when batteries are discharged Will not trip any RCD when testing across Live and Earth Single pole detection when L2 probe connected above 100V
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 4 Channels
M4I.6622-X8
Arbitrary Waveform Generator
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
Product
CATV Line-Amplifier EDFA
HA5200
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5200 series C-Band line-amplifier EDFA (also knows as relay EDFA), is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Fiber CATV system operates generally in single wavelength that has no strict requirement on gain flatness. In order to reduce the effect of CNR deterioration caused by EDFA, input power should be as high as possible to make EDFA operate in saturated output power. The typical value of input power is >+3dBm.
-
Product
Computer Conversions GT Transducers
DHM
-
Computer Conversions Corporation
Computer Conversions GT Transducers are brushless, Electromagnetic, Rotary Sensors used to provide Precise Absolute or Incremental Position, and Velocity feedback in harsh environments. All Computer Conversions Transducers are continuous rotation, bi-directional, and electronically passive devices (no electronic componenets to degrade or fail), that require zero maintenance, and may be installed in virtually inaccessible locations.
-
Product
Portable Circuit Breaker Tester
PI-1600
-
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
Product
Strain Gauge Weighing
-
In the demanding environment of the metals processing industry getting the right balance between accuracy, speed and reliability in your sensing systems can mean a great deal. ABB offers a wide range of dedicated products for weighing applications for crane, scrap, blast furnace and continuous casting.
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
Product
Handheld RF Spectrum Analyzer With 10MHz To 3.6 Or 6.0GHz Bandwidth Options
PSA Series 5
-
10MHz to 3600MHz or 6000MHz frequency rangeResolution bandwidths from 300Hz to 10MHz (1:3:10)-120dBm typical noise floor at -40dBm ref. level/10kHz RBWMeasurement in dBm or dBµV, mV or µWZero span mode with AM and FM audio demodulationTrace modes of normal, peak hold and trace averageLive, View and Reference traces in contrasting coloursTwin markers with readout of absolute & difference valuesSmart marker movement with selectable peak trackingFrequency counter with down to 10Hz resolutionFrequency presets and independent state storageAuto-find automatically sets sweep parameters for the highest signal foundUnlimited storage for waveforms, set-ups and screensUser assignable file names, file stamping from real-time clockUSB interfaces for Flash drives and PC connectionComprehensive status and context sensitive help screensRechargeable lithium ion battery giving more than 3 hours continuous operation from a chargeSmaller and lighter than other spectrum analyzers (weight only 0.56 kg)
-
Product
Oxygen Sensor
KS60051
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Handheld Wiring Analyzer
HT-128
-
Simplify your wire harness testing. The DIT-MCO HT-128 provides a superior solution for point-to-point continuity analysis. These lightweight, handheld units can serve your diagnostic needs from product development and benchtop testing through field support and maintenance.
-
Product
Microwave Moisture Meter
RX-95
-
The system works based on the absorption of microwave energy by water molecules contained inthe x-rayed material. It is a non-contact, non-destructive method of instant measurement of water content - used for materials such as coal, flour, grain, cement, seeds, sugar, etc. Thanks to high measurement sensitivity (resolution greater than 0.01% of water content by weight), short measurement time (about 5 times/sec.) and repeatability of measurement - the system is suitable for continuous measurement of material moisture, e.g. on conveyor belts and its recording on a PC or using a 4-20 mA current loop.
-
Product
Equipment
-
Based on a proprietary light engine, our solar simulation equipment delivers perfect and continuous artificial sunlight 24/7, allowing for accurate stability and performance assessments of solar cells at laboratory and industrial scales.
-
Product
EDFA
SPA-32-XX
-
Hangzhou Softel Optic Co., Ltd.
1550nm series multi-outputs optical amplifier gain spectrum bandwidth between 1545`1563nm, adopt high reliability multimode pump laser and double clad fiber, the unique APC, ACC and ATC circuit, the max output power can reach to 40dBm, one device and replace the original several to dozens traditional EFDA, can greatly save the cost and maintenance expense, improves the stability of the network operation, high output power 1550nm optical amplifier is playing an increasingly important role in the continuous extension of the optical fiber network, providing a flexible and low-cost solution for the wide coverage of CATV system in large and medium-size cities.
-
Product
Geiger Counter, Survey Meter and Dosimeter
NukAlert-ER
-
The NukAlert-ER™, with its unique 'Extended Range' Continuous Coverage from 1µR/hr through 600R/hr, performs all of the functions of the three devices that constituted our now lapsed Civil Defense Program.
-
Product
Triple Output Power Supply
U8030 Series
-
The Keysight U8030 Series variable DC power supply has a total output of 375 W—making this solution an ideal power source in the design and manufacturing of electronic devices. The U8030 Series power supplies feature an output sequencing capability for semiautomated tests. These power supplies enable you to generate output sequences with minimal programming skills. This solution features excellent load regulation and clean output noise for continued stability.
-
Product
Professional Thermal Camera
FLIR T540
-
Diagnose potential faults in industrial, electrical, and mechanical systems, or discover temperature anomalies in R&D testing with the 464 × 348 resolution FLIR T540. This portable, ergonomic thermal camera offers advanced features like 1-Touch Level/Span and continuous laser-assisted autofocus, making it the perfect non-contact diagnostic tool for condition monitoring and research applications. Streamline electrical/mechanical surveys, troubleshooting, and repairs with Inspection Route mode, which runs pre-planned routes created in FLIR Thermal Studio Pro (Route Creator plugin required) so users can record temperature data and imagery in a logical sequence. The built-in Macro Mode allows R&D users to quickly switch from wide angle to close-up analysis without changing the lens. When coupled with Research Studio software, the T540 helps engineers assess unexpected hot spots and find potential design flaws. The T540 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. The purchase of a T540 camera includes a 3-month subscription to FLIR Thermal Studio Pro and FLIR Route Creator.
-
Product
Voltage Sag Generator
SKS-1132GTB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
Small Engine Dynos
M2 Series
-
Taylor Dynamometer’s M2 Series small engine dynamometers are designed to handle your most difficult operating conditions and are capable of unlimited, continuous use.
-
Product
Integrating Sphere Light Sources
-
Integrating sphere light sources with LED based or continuous broadband emission spectrum for use as luminance standards for camera calibration, for the determination of veiling glare, for the adjustment of night vision devices and much more. Diameters in the range from 50 mm to 500 mm with options like monitor detector, signal output control by manual and remote apertures and much more.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Multifunction Meters
-
Measures V, A, PF, Hz, KW, KVA, KVAr, Kwh, KVAh & KVArhTRMS MeasurementCan be used for Continuous MonitoringAuto / Manual Scroll Display (User Selectable)State of Art Microcontroller DesignPortable, Handy, Plug-n-Play and Easy-to-useLCD Display with BacklightRS-485 5KV Isolated Port (Optional) with MODBUS RTU Protocol (Optional)POWER MASTER Software for MIS Reports (Optional)
