Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
IEC/EN Event Recorders
-
Improving train operation safety is a continuous process that affects the entire railway system and its organization. To keep pace with technology, operating systems once thought to be at the leading edge now need to be replaced and/or upgraded—or risk becoming obsolete. At the same time, optimizing costs is a must. To meet these challenges, you require flexible and modular solutions to help you improve train operation safety and correctly interface with new signaling systems.
-
Product
Liquid Level Sensor
LevelMaster
-
The LevelMaster combines the industry’s most innovative hardware and software to address the unique custody-measurement and operational needs of tank-level management. The LevelMaster provides not only an accurate level gauge, but also an accurate measurement of the oil and water interface.Unlike other level-sensing technologies, LevelMaster provides precise levels without having to continuously adjust for changes in the unpredictable properties of storage-tank liquids. LevelMaster floats can measure oil, water, and emulsion levels up to 25 feet (7.6 m) deep, with a standard relative accuracy of 0.1 inch (2.5 mm) or optional high-precision relative accuracy of 0.05 inch (1.25 mm).
-
Product
Voltage Sag Generator
SKS-1120GTB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
-
Product
Level Measurement
Level Measurement
-
AMETEK Sensors, Test & Calibration
B/W Controls uses the same advanced magnetostrictive technology as in Gemco products providing high accuracy and reliability for continuous liquid level measurement.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786167-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Digital Multi-Meter
7124A
-
Peaceful Thriving Enterprise Co Ltd
This is a low power consumption, high accuracy, and stable hand held 3 1/2digits (2000 counts) multimeter; with special designed IC to support true RMS measurement. It performs measurements of DC voltage / current, true RMS AC voltage / current, resistance, diode, continuity, and non-contact voltage sensing.
-
Product
Non-contact Inline Sheet Resistance Measurement Module For Flat Panel Display
NC-600
-
*Non-stop and non-contact sheet resistance measuring of thin film on glass runs through on conveyer*1 to 10 number of probe by sizes of glass is attachable*Glass collision prevention function*Continuous test data report to the host computer
-
Product
Horizontal Calibration Instruments (Lab)
Labconcept Nano
-
The Labconcept Nano is a new reference in the field of dimensional metrology. It integrates 40 years of knowledge and continuous improvement. It is a remarkable instrument for all measuring tasks that require extremely high accuracy.
-
Product
Telos Systems
-
Telos Systems—part of the Telos Alliance—was founded in 1985 by Steve Church, a talk show radio host and engineer who was dissatisfied with the poor quality of the on-air telephone calls on his shows. He was also an Engineer determined to do something about it. The resulting Telos 10 telephone interface system was a great success, inspiring Steve to build a business to make and sell the systems. Telos Systems has since become the industry leader in broadcast telephone systems and IP and ISDN codecs. The breakthrough Telos Zephyr audio codec, for example, is one of the most successful digital broadcast products in history, with more than 21,000 in use worldwide. Telos telephone hybrids and on-air talk show systems set the performance benchmark for the industry, and we continue to pioneer groundbreaking technology that pushes boundaries and gives broadcasters the telephony solutions they need for reliability, efficiency, and the best possible sound quality.
-
Product
Software
SourceLink
-
Specifically designed to maximize production with Continuous Recording Systems like iSeis Sigma, OYO GSR, Fairfield Node, Sercel Unite and all other systems.
-
Product
Functional Test Fixtures
-
Intrinsic Quality delivers turnkey standalone Functional Test fixtures and Windows based functional testers that are custom engineered with innovation and reliability to meet your testing needs. Our experience and expertise ensure a production ready functional test solution that is cost-effective, on time and on budget. Our broad range of test solutions includes simple continuity testers to complex microcontroller assembly testers. Our customers include military, aerospace, automotive, medical and consumer OEMs. We serve the needs of low volume high mix CEMs and off shore high volume manufacturers.
-
Product
Power Clamp Meters
-
TES Electrical Electronic Corp.
Communication with PC. 4000 continuity point data logger, 25 point manual data logger. True power/ apparent Power/ Power Fractor Measurement. True RMS. V,A,W cap Ind, phase indicator.
-
Product
Wi-Fi Survey App
Wi-Fi® MOBILE
-
Take iBwave Wi‑Fi® Mobile on‑site with you to collect survey measurements, capture site visuals to geo‑located pushpins, and start your network design. Save all of your site survey information in a single file in the iBwave Cloud where you or anyone on your team can easily access the file again to continue the design on either your mobile device or the more powerful PC version, iBwave Wi‑Fi®.
-
Product
Columns, Reagents And Consumables
-
For over 140 years, Shimadzu has continued to be your trusted partner by providing leading-edge analytical instruments. Now we further support your success through borderless delivery of the high quality consumable products that solve everyday challenges. All this is for the pursuit of our corporate philosophy "Contributing to Society through Science and Technology".
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 1 Channel
M2P.6530-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
Multifunction Electrical Installation Meter
AMPI-520
-
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
Product
Platform for Multi camera systems and Embedded vision
xiX
-
*Smallest camera featuring Sony Pregius™ - Compact with only 26.4 x 26.4 x 31 mm and 30 grams (1)*Fast CMOS - High speed, high frame rate: from 2.3 Mpix at 166 Fps to 50 Mpix at 33 Fps*Cool economy - Low power consumption with under 3 Watt and minimal heat dissipation*All-around support - support for Windows 7 and 10, macOS, Linux, ARM and embedded platforms*Industry standard - Data and control interface complies with PCI Express External Cabling Specifications*Adaptable potential - Available with two flat ribbon flex cable connectors: parallel and perpendicular *Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Connectivity and Synchronization - Programmable opto-isolated input and output, 4 status LEDs*Lens control - EF-mount Interface allows remote control of aperture, focus and image stabilization*Highly Customizable - Variety of sensor options including Sony IMX287, IMX273, IMX249, IMX265, IMX264, IMX267, IMX304 available in board level stack for OEM use and with switches and adapters*Interoperability increase - Continuous embrace of new software and hardware partners*Cost efficient - Excellent value through utilization of the newest technologies including Sony Pregius™
-
Product
Electrical Safety Wall
-
AllWin Instrument Science and Technology Co., Ltd.
1. Electricity Safety Wall2. 50/60HZ3. Four detection ways4. Continuous testing
-
Product
Point IR Gas Detector
IR400
-
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
Product
Oil Breakdown Voltage Tester
DTA IL
-
Insulating oil testing with the BAUR DTA IL. The BAUR DTA Inline is a high performance and reliable oil tester for continuous testing of the breakdown strength of insulating oils during production (inline tests). The combination of extremely short switch-off times during breakdowns and the easy oil sample handling facilitate high quality statements and conclusions on the insulating oil quality.
-
Product
Visual Fault Locator
HW-205
-
Shanghai Fibretool Technology Co.,Ltd.
The HW-205 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.- 2.5mm universal connector- Operates either in CW or Pulsed- Constant output power- Long battery life (up to 60 hours)- Laser case ground design prevents ESD damage- Portable and rugged, easy to use- Burning testing to ensure the reliability.- Optional 1.25mm connector adapter
-
Product
Sola-Scope
-
This was the forerunner of and has been superseded by the Sola-Check System. Solatell continues to support this device for repairs , service and calibration as well as accessories. We offer trade-in discounts for upgrades to Sola-Check system against return of your old Sola-Scope.
-
Product
Noise Monitoring System
NoiseTutor
-
Continuous monitoring of environmental data in remote areas has always presented a unique set of challenges. Typical solutions involve complex installations, frequent visits to remote locations to keep the system fully operational and require expert level attention to retrieve and share data amongst customers, consultants and project leads.
-
Product
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
Product
Total Sulfur Process Analyzer
NEX XT
-
Applied Rigaku Technologies, Inc
Featuring third-generation X-ray transmission technology, the NEX XT represents the next evolution of process gauge for sulfur measurement (0.02% to 6% S) of crude, bunker fuel, fuel oils, and other highly viscous hydrocarbons, including residuums.The Rigaku NEX XT system is faster, more sensitive and far more compact than competitive systems, and provides continuous, reliable detection of sulfur at pressures up to 1480 psig. Rigaku NEX XT can operate as a stand-alone analyzer or provide real-time closed-loop control when tied into a blending or plant-wide automation system. Among its other key features are a simplified user interface, reduced standards requirement, automatic density compensation, password protection, and standard platform for communicating sulfur and density to a plant-wide DCS. Due to its unique design and robust construction, sample conditioning and recovery systems are typically not required.
-
Product
Digital Multimeter
MM-2
-
Our compact, low cost Model MM-2 Digital Multimeter with True RMS is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC voltage to 1000 V and AC voltage to 750 V, DC and AC current to 10 A and resistance to 400 Ohms. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. The rotary switch allows you to select from any of the functions quickly and easily.
-
Product
Solid Walk-In Chambers
-
EWS chambers are solid, one-piece construction, using fiberglass insulation and an angle-iron frame. The stainless steel interior liner is reinforced and continuously welded, including leak-testing for integrity.
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
